aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
authorMuhammad AL-Qadhy <m.ismael@gmail.com>2023-03-21 08:49:22 +0200
committerHauke Mehrtens <hauke@hauke-m.de>2023-04-01 22:13:16 +0200
commit2a04df39200dd1d5d3c3099c548bb9f82e03ab54 (patch)
treea02a6b5f1473e1626657f7828647a5cd3c778e11 /target/linux
parent69a14e4230ef459a9787b1fa1776fbac59012dbb (diff)
downloadupstream-2a04df39200dd1d5d3c3099c548bb9f82e03ab54.tar.gz
upstream-2a04df39200dd1d5d3c3099c548bb9f82e03ab54.tar.bz2
upstream-2a04df39200dd1d5d3c3099c548bb9f82e03ab54.zip
ramips: Add support for CJ-Hello HYC-G920
Hanyang Digitech Co., Ltd. MSIP-CMM-HYD-HYC-G920 CJ-Hello HYC-G920 SoC : MediaTek MT7621AT RAM : 256M (SK hynix H5TQ2G63FFR) FLASH : 16MB (Winbond W25Q128BV) WiFi : MediaTek MT7602EN bgn 2SS WiFi : MediaTek MT7612EN nac 2SS BTN : Reset LED : - Power RED - WAN Green - LAN {1-4} - WiFi 2.4 GHz Blue - WiFi 5 GHz Blue - USB Green **For MT7621 stage1 DDR Test** UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1 ``` MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ``` **For u boot environment** UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1 **UART Menu** ``` Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. ``` **Steps** Press 4: Entr boot command line interface. On the pormpt enter. `setenv firmware_size 0xf60000` Then enter. `saveenv` Then enter. `reset` **Device will reboot** Set your IP 192.168.100.100/24 Connect your lan cable to wan port. **On the UART Menu** Press 2: Load system code then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y` Please Input new ones /or Ctrl-C to discard Input device IP (192.168.100.55) ==:`192.168.100.55` Input server IP (192.168.100.100) ==:`192.168.100.100` Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin` After uploading firmware image, device will boot Openwrt. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
Diffstat (limited to 'target/linux')
-rw-r--r--target/linux/ramips/dts/mt7621_hanyang_hyc-g920.dts196
-rw-r--r--target/linux/ramips/image/mt7621.mk10
2 files changed, 206 insertions, 0 deletions
diff --git a/target/linux/ramips/dts/mt7621_hanyang_hyc-g920.dts b/target/linux/ramips/dts/mt7621_hanyang_hyc-g920.dts
new file mode 100644
index 0000000000..db341ab87b
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_hanyang_hyc-g920.dts
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "hanyang,hyc-g920", "mediatek,mt7621-soc";
+ model = "CJ-Hello HYC-G920";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ bootargs-override = "console=ttyS0,115200";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "red:power";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ usb {
+ label = "green:usb";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&ehci_port2>;
+ linux,default-trigger = "usbport";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "bootloader";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "mac";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition@40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition@50000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x50000 0xfb0000>;
+ };
+
+ partition@fb0000 {
+ label = "config ";
+ reg = <0xfb0000 0x20000>;
+ read-only;
+ };
+
+ partition@fd0000 {
+ label = "config_bak ";
+ reg = <0xfd0000 0x20000>;
+ read-only;
+ };
+
+ partition@ff0000 {
+ label = "mac_bak ";
+ reg = <0xff0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi@0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+
+ led {
+ led-sources = <2>;
+ led-active-low;
+ };
+ };
+};
+
+&pcie1 {
+ wifi@0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x0000>;
+
+ led {
+ led-sources = <2>;
+ led-active-low;
+ };
+ };
+};
+
+&gmac0 {
+ nvmem-cells = <&macaddr_factory_4>;
+ nvmem-cell-names = "mac-address";
+};
+
+&switch0 {
+ ports {
+ port@0 {
+ status = "okay";
+ label = "wan";
+ nvmem-cells = <&macaddr_factory_4>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <1>;
+ };
+
+ port@1 {
+ status = "okay";
+ label = "lan1";
+ };
+
+ port@2 {
+ status = "okay";
+ label = "lan2";
+ };
+
+ port@3 {
+ status = "okay";
+ label = "lan3";
+ };
+
+ port@4 {
+ status = "okay";
+ label = "lan4";
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "sdhci";
+ function = "gpio";
+ };
+};
+
+&factory {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_factory_4: macaddr@4 {
+ reg = <0x4 0x6>;
+ };
+
+ macaddr_factory_8004: macaddr@8004 {
+ reg = <0x8004 0x6>;
+ };
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index dfe9d346f1..066602dafd 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -974,6 +974,16 @@ define Device/gnubee_gb-pc2
endef
TARGET_DEVICES += gnubee_gb-pc2
+define Device/hanyang_hyc-g920
+ $(Device/dsa-migration)
+ $(Device/uimage-lzma-loader)
+ DEVICE_VENDOR := Hanyang
+ DEVICE_MODEL := CJ-Hello HYC-G920
+ IMAGE_SIZE := 15744k
+ DEVICE_PACKAGES := kmod-usb3 kmod-mt76x2 kmod-usb-ledtrig-usbport
+endef
+TARGET_DEVICES += hanyang_hyc-g920
+
define Device/h3c_tx180x
$(Device/dsa-migration)
BLOCKSIZE := 128k