aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
authorSven Eckelmann <sven@narfation.org>2020-11-23 13:41:34 +0100
committerAdrian Schmutzler <freifunk@adrianschmutzler.de>2020-12-30 23:32:07 +0100
commit80713657b20d58c2fb7fa503e24cbf7db379550f (patch)
tree9c32cb3932f60c063e84630c1818c92d204b405e /target/linux
parentff9e48e75c191e0d7e08a14791853559d509ca2e (diff)
downloadupstream-80713657b20d58c2fb7fa503e24cbf7db379550f.tar.gz
upstream-80713657b20d58c2fb7fa503e24cbf7db379550f.tar.bz2
upstream-80713657b20d58c2fb7fa503e24cbf7db379550f.zip
ath79: Add support for OpenMesh OM5P
Device specifications: ====================== * Qualcomm/Atheros AR9344 rev 2 * 560/450/225 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 5 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + builtin switch port 1 + used as LAN interface - eth1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas WAN/LAN LEDs appear to be wrong in ar71xx and have been swapped here. Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org> [add LED swap comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Diffstat (limited to 'target/linux')
-rw-r--r--target/linux/ath79/dts/ar9344_openmesh_om5p.dts166
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/01_leds1
-rw-r--r--target/linux/ath79/generic/base-files/lib/upgrade/platform.sh3
-rw-r--r--target/linux/ath79/image/generic.mk19
4 files changed, 188 insertions, 1 deletions
diff --git a/target/linux/ath79/dts/ar9344_openmesh_om5p.dts b/target/linux/ath79/dts/ar9344_openmesh_om5p.dts
new file mode 100644
index 0000000000..a733a922e4
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_openmesh_om5p.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "openmesh,om5p", "qca,ar9344";
+ model = "OpenMesh OM5P";
+
+ chosen {
+ /delete-property/ bootargs;
+ };
+
+ aliases {
+ serial0 = &uart;
+ led-boot = &led_power_blue;
+ led-failsafe = &led_power_blue;
+ led-running = &led_power_blue;
+ led-upgrade = &led_power_blue;
+ label-mac-device = &eth1;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_lan_wan_blue_pin>;
+
+ led_power_blue: power_blue {
+ label = "blue:power";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wan_blue {
+ label = "blue:wan";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ lan_blue {
+ label = "blue:lan";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi_green {
+ label = "green:wifi";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wifi_yellow {
+ label = "yellow:wifi";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi_red {
+ label = "red:wifi";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ hw_algo = "toggle";
+ /* hw_margin_ms is actually 300s but driver limits it to 60s */
+ hw_margin_ms = <60000>;
+ always-running;
+ };
+};
+
+&ref {
+ clock-frequency = <40000000>;
+};
+
+&uart {
+ status = "okay";
+};
+
+&pinmux {
+ led_lan_wan_blue_pin: pinmux_lan_wan_blue_pin {
+ pinctrl-single,bits = <0xc 0x0 0xffff0000>;
+ };
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ /* partitions are passed via bootloader */
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ partition@50000 {
+ label = "custom";
+ reg = <0x050000 0x060000>;
+ read-only;
+ };
+
+ partition@b0000 {
+ label = "inactive";
+ reg = <0x0b0000 0x7a0000>;
+ };
+
+ partition@850000 {
+ label = "inactive2";
+ reg = <0x850000 0x7a0000>;
+ };
+
+ art: partition@ff0000 {
+ label = "ART";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&eth0 {
+ status = "okay";
+
+ phy-handle = <&swphy4>;
+
+ mtd-mac-address = <&art 0x6>;
+};
+
+&eth1 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 8f0e2f87a7..b961e7d3e8 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -150,6 +150,7 @@ openmesh,om2p-hs-v1|\
openmesh,om2p-hs-v2|\
openmesh,om2p-hs-v3|\
openmesh,om2p-lc|\
+openmesh,om5p|\
telco,t1)
ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02"
ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1"
diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
index 2c907ac101..79e023482b 100644
--- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
@@ -56,7 +56,8 @@ platform_do_upgrade() {
openmesh,om2p-hs-v2|\
openmesh,om2p-hs-v3|\
openmesh,om2p-hs-v4|\
- openmesh,om2p-lc)
+ openmesh,om2p-lc|\
+ openmesh,om5p)
PART_NAME="inactive"
platform_do_upgrade_openmesh "$1"
;;
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index acb456ba44..ded8e29c2c 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1630,6 +1630,25 @@ define Device/openmesh_om2p-lc
endef
TARGET_DEVICES += openmesh_om2p-lc
+define Device/openmesh_om5p-common
+ SOC := ar9344
+ DEVICE_VENDOR := OpenMesh
+ DEVICE_PACKAGES := uboot-envtools
+ IMAGE_SIZE := 7808k
+ BLOCKSIZE := 64k
+ KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
+ pad-to $$(BLOCKSIZE)
+ IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
+ openmesh-image ce_type=OM5P | append-metadata
+endef
+
+define Device/openmesh_om5p
+ $(Device/openmesh_om5p-common)
+ DEVICE_MODEL := OM5P
+ SUPPORTED_DEVICES += om5p
+endef
+TARGET_DEVICES += openmesh_om5p
+
define Device/openmesh_om5p-ac-v2
SOC := qca9558
DEVICE_VENDOR := OpenMesh