aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
authorPiotr Dymacz <pepe2k@gmail.com>2020-09-18 18:55:23 +0200
committerPiotr Dymacz <pepe2k@gmail.com>2020-09-28 01:28:37 +0200
commit6492ea7d9e4f2a392e8576b5fdaa76815d3c6350 (patch)
treefafcc77c802a33d08bab77e80cb944aac1f0f480 /target/linux
parent9181b039f3d8df3edb9feff074840b69b504099d (diff)
downloadupstream-6492ea7d9e4f2a392e8576b5fdaa76815d3c6350.tar.gz
upstream-6492ea7d9e4f2a392e8576b5fdaa76815d3c6350.tar.bz2
upstream-6492ea7d9e4f2a392e8576b5fdaa76815d3c6350.zip
ath79: add support for ALFA Network N2Q
ALFA Network N2Q is an outdoor N300 AP/CPE based on Qualcomm/Atheros QCA9531 v2. This model is a successor of the old N2 which was based on Atheros AR7240. FCC ID: 2AB8795311. Specifications: - Qualcomm/Atheros QCA9531 v2 - 650/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 2T2R 2.4 GHz Wi-Fi with ext. PA (Skyworks SE2623L) and LNA - 2x 10/100 Mbps Ethernet with passive PoE input in one port (24 V) - PoE pass through in second port (controlled by GPIO) - support for optional 802.3af/at PoE module - 1x mini PCIe slot (PCIe bus, extra 4.2 V for high power cards) - 2x IPEX/U.FL connectors on PCB - 1x USB 2.0 mini Type-B (power controlled by GPIO) - 8x LED (7 of them are driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, enabled by default) - UART (4-pin, 2.54 mm pitch) header on PCB - LEDs (2x 5-pin, 2.54 mm pitch) header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Diffstat (limited to 'target/linux')
-rw-r--r--target/linux/ath79/dts/qca9531_alfa-network_n2q.dts120
-rw-r--r--target/linux/ath79/dts/qca9531_alfa-network_r36a.dts135
-rw-r--r--target/linux/ath79/dts/qca9531_alfa-network_r36a.dtsi126
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/01_leds8
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/02_network12
-rw-r--r--target/linux/ath79/image/generic.mk10
6 files changed, 283 insertions, 128 deletions
diff --git a/target/linux/ath79/dts/qca9531_alfa-network_n2q.dts b/target/linux/ath79/dts/qca9531_alfa-network_n2q.dts
new file mode 100644
index 0000000000..8dd91ab38b
--- /dev/null
+++ b/target/linux/ath79/dts/qca9531_alfa-network_n2q.dts
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9531_alfa-network_r36a.dtsi"
+
+/ {
+ model = "ALFA Network N2Q";
+ compatible = "alfa-network,n2q", "qca,qca9531";
+
+ aliases {
+ led-boot = &led_usb;
+ led-failsafe = &led_usb;
+ led-upgrade = &led_usb;
+ };
+
+ gpio-export-pcf8574 {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ poe-passthrough {
+ gpio-export,name = "poe-passthrough";
+ gpio-export,output = <1>;
+ gpios = <&pcf8574 0 GPIO_ACTIVE_LOW>;
+ };
+
+ usb-power {
+ gpio-export,name = "usb-power";
+ gpio-export,output = <0>;
+ gpios = <&pcf8574 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ i2c {
+ compatible = "i2c-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sda-gpios = <&gpio 11 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+ pcf8574: pcf8574@20 {
+ compatible = "nxp,pcf8574";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&enable_gpio4 &enable_gpio16>;
+
+ lan1 {
+ label = "n2q:orange:lan1";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ lan2 {
+ label = "n2q:orange:lan2";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ led_usb: usb {
+ label = "n2q:green:usb";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "usbport";
+ trigger-sources = <&hub_port0>;
+ };
+
+ minipcie {
+ label = "n2q:green:minipcie";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan {
+ label = "n2q:green:wlan";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+
+ leds-pcf8574 {
+ compatible = "gpio-leds";
+
+ poe-passthrough {
+ label = "n2q:green:poe-passthrough";
+ gpios = <&pcf8574 1 GPIO_ACTIVE_LOW>;
+ };
+
+ signal1 {
+ label = "n2q:red:signal1";
+ gpios = <&pcf8574 3 GPIO_ACTIVE_LOW>;
+ };
+
+ signal2 {
+ label = "n2q:orange:signal2";
+ gpios = <&pcf8574 4 GPIO_ACTIVE_LOW>;
+ };
+
+ signal3 {
+ label = "n2q:green:signal3";
+ gpios = <&pcf8574 5 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&eth0 {
+ mtd-mac-address = <&art 0x1002>;
+ mtd-mac-address-increment = <(-2)>;
+};
+
+&eth1 {
+ mtd-mac-address = <&art 0x1002>;
+ mtd-mac-address-increment = <(-1)>;
+};
+
+&pcie0 {
+ status = "okay";
+};
diff --git a/target/linux/ath79/dts/qca9531_alfa-network_r36a.dts b/target/linux/ath79/dts/qca9531_alfa-network_r36a.dts
index 18aaa85f5c..0405e40839 100644
--- a/target/linux/ath79/dts/qca9531_alfa-network_r36a.dts
+++ b/target/linux/ath79/dts/qca9531_alfa-network_r36a.dts
@@ -1,57 +1,18 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-#include "qca953x.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "qca9531_alfa-network_r36a.dtsi"
/ {
model = "ALFA Network R36A";
compatible = "alfa-network,r36a", "qca,qca9531";
aliases {
- label-mac-device = &wmac;
led-boot = &led_status;
led-failsafe = &led_status;
led-running = &led_status;
led-upgrade = &led_status;
};
- gpio-export {
- compatible = "gpio-export";
- #size-cells = <0>;
-
- usb-power {
- gpio-export,name = "usb-power";
- gpio-export,output = <1>;
- gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
- };
-
- watchdog-enable {
- gpio-export,name = "watchdog-enable";
- gpio-export,output = <1>;
- gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
- };
- };
-
- keys {
- compatible = "gpio-keys";
-
- reset {
- label = "reset";
- linux,code = <KEY_RESTART>;
- gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
- debounce-interval = <60>;
- };
-
- rfkill {
- label = "rfkill";
- linux,code = <KEY_RFKILL>;
- gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
- debounce-interval = <60>;
- };
- };
-
leds {
compatible = "gpio-leds";
@@ -86,20 +47,9 @@
linux,default-trigger = "phy0tpt";
};
};
-
- watchdog {
- compatible = "linux,wdt-gpio";
- gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
- hw_algo = "toggle";
- hw_margin_ms = <25000>;
- always-running;
- };
};
&eth0 {
- status = "okay";
-
- phy-handle = <&swphy4>;
mtd-mac-address = <&art 0x0>;
};
@@ -111,80 +61,19 @@
mtd-mac-address = <&art 0x6>;
};
-&pinmux {
- enable_gpio4: pinmux_enable_gpio4 {
- pinctrl-single,bits = <0x04 0x0 0xff>;
- };
-
- enable_gpio16: pinmux_enable_gpio16 {
- pinctrl-single,bits = <0x10 0x0 0xff>;
- };
-};
-
-&spi {
- status = "okay";
-
- num-cs = <1>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <50000000>;
- m25p,fast-read;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "u-boot";
- reg = <0x000000 0x060000>;
- read-only;
- };
-
- partition@60000 {
- label = "u-boot-env";
- reg = <0x060000 0x010000>;
- };
-
- art: partition@70000 {
- label = "art";
- reg = <0x070000 0x010000>;
- read-only;
- };
-
- partition@80000 {
- compatible = "denx,uimage";
- label = "firmware";
- reg = <0x080000 0xf80000>;
- };
- };
+&gpio_export {
+ usb-power {
+ gpio-export,name = "usb-power";
+ gpio-export,output = <1>;
+ gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
};
};
-&uart {
- status = "okay";
-};
-
-&usb0 {
- status = "okay";
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- hub_port0: port@1 {
- reg = <1>;
- #trigger-source-cells = <0>;
+&keys {
+ rfkill {
+ label = "rfkill";
+ linux,code = <KEY_RFKILL>;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
};
};
-
-&usb_phy {
- status = "okay";
-};
-
-&wmac {
- status = "okay";
-
- mtd-cal-data = <&art 0x1000>;
-};
diff --git a/target/linux/ath79/dts/qca9531_alfa-network_r36a.dtsi b/target/linux/ath79/dts/qca9531_alfa-network_r36a.dtsi
new file mode 100644
index 0000000000..697b20e999
--- /dev/null
+++ b/target/linux/ath79/dts/qca9531_alfa-network_r36a.dtsi
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca953x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ aliases {
+ label-mac-device = &wmac;
+ };
+
+ gpio_export: gpio-export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ watchdog-enable {
+ gpio-export,name = "watchdog-enable";
+ gpio-export,output = <1>;
+ gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys: keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ hw_algo = "toggle";
+ hw_margin_ms = <25000>;
+ always-running;
+ };
+};
+
+&eth0 {
+ status = "okay";
+
+ phy-handle = <&swphy4>;
+};
+
+&pinmux {
+ enable_gpio4: pinmux_enable_gpio4 {
+ pinctrl-single,bits = <0x04 0x0 0xff>;
+ };
+
+ enable_gpio16: pinmux_enable_gpio16 {
+ pinctrl-single,bits = <0x10 0x0 0xff>;
+ };
+};
+
+&spi {
+ status = "okay";
+
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x060000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "u-boot-env";
+ reg = <0x060000 0x010000>;
+ };
+
+ art: partition@70000 {
+ label = "art";
+ reg = <0x070000 0x010000>;
+ read-only;
+ };
+
+ partition@80000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x080000 0xf80000>;
+ };
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub_port0: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 6e488949e4..0b522910ee 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -17,6 +17,14 @@ alfa-network,ap121fe|\
avm,fritz450e)
ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
;;
+alfa-network,n2q)
+ ucidef_set_led_netdev "lan2" "LAN2" "$boardname:orange:lan2" "eth1"
+ ucidef_set_led_switch "lan1" "LAN1" "$boardname:orange:lan1" "switch0" "0x10"
+ ucidef_set_rssimon "wlan0" "200000" "1"
+ ucidef_set_led_rssi "signal1" "SIGNAL1" "$boardname:red:signal1" "wlan0" "1" "100"
+ ucidef_set_led_rssi "signal2" "SIGNAL2" "$boardname:orange:signal2" "wlan0" "33" "100"
+ ucidef_set_led_rssi "signal3" "SIGNAL3" "$boardname:green:signal3" "wlan0" "66" "100"
+ ;;
alfa-network,r36a)
ucidef_set_led_netdev "lan" "LAN" "$boardname:blue:lan" "eth0"
ucidef_set_led_switch "wan" "WAN" "$boardname:blue:wan" "switch0" "0x10"
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index d13d714f88..160eea523c 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -78,6 +78,12 @@ ath79_setup_interfaces()
alfa-network,ap121fe)
ucidef_set_interface_lan "eth0 usb0"
;;
+ alfa-network,n2q|\
+ devolo,dvl1200e|\
+ devolo,dvl1750e|\
+ ocedo,ursus)
+ ucidef_set_interface_lan "eth0 eth1"
+ ;;
avm,fritz4020|\
pcs,cr3000|\
tplink,archer-c58-v1|\
@@ -147,11 +153,6 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "3:lan" "2:wan"
;;
- devolo,dvl1200e|\
- devolo,dvl1750e|\
- ocedo,ursus)
- ucidef_set_interface_lan "eth0 eth1"
- ;;
devolo,magic-2-wifi)
ucidef_add_switch "switch0" \
"0@eth0" "2:wan" "3:lan" "4:lan"
@@ -402,6 +403,7 @@ ath79_setup_macs()
;;
alfa-network,ap121f|\
alfa-network,ap121fe|\
+ alfa-network,n2q|\
alfa-network,r36a|\
engenius,ens202ext-v1)
label_mac=$(mtd_get_mac_binary art 0x1002)
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 605f66f77f..920e2e5cee 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -237,6 +237,16 @@ define Device/alfa-network_ap121fe
endef
TARGET_DEVICES += alfa-network_ap121fe
+define Device/alfa-network_n2q
+ SOC := qca9531
+ DEVICE_VENDOR := ALFA Network
+ DEVICE_MODEL := N2Q
+ DEVICE_PACKAGES := kmod-i2c-gpio kmod-gpio-pcf857x kmod-usb2 \
+ kmod-usb-ledtrig-usbport rssileds
+ IMAGE_SIZE := 15872k
+endef
+TARGET_DEVICES += alfa-network_n2q
+
define Device/alfa-network_r36a
SOC := qca9531
DEVICE_VENDOR := ALFA Network