ipq40xx: add support for EnGenius EMD1

SOC:     IPQ4018 / QCA Dakota
CPU:     Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:    256 MiB
NOR:     32 MiB
ETH:     Qualcomm Atheros QCA8072 (1 port)
WLAN1:   Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:   Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:   RESET Button
LEDS:    White, Blue, Red, Orange

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMD1. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
   (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img
4. Flash the firmware
   (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
   (IPQ40xx) # reset

Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[removed BOARD_NAME]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

5 files changed, 261 insertions, 1 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 9cfc43f1f9..4b636fc701 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -49,6 +49,7 @@ ipq40xx_setup_interfaces()
 	avm,fritzrepeater-1200|\
 	dlink,dap-2610 |\
 	engenius,eap1300|\
+	engenius,emd1|\
 	meraki,mr33|\
 	netgear,ex6100v2|\
 	netgear,ex6150v2|\
@@ -108,6 +109,10 @@ ipq40xx_setup_macs()
 		lan_mac=$(mtd_get_mac_ascii bdcfg lanmac)
 		label_mac=$lan_mac
 		;;
+	engenius,emd1)
+		lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
+		label_mac=$lan_mac
+		;;
 	engenius,ens620ext)
 		wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
 		lan_mac=$(macaddr_add "$wan_mac" 1)
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 22ac6eefc5..957bee12ab 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -91,6 +91,10 @@ case "$FIRMWARE" in
 		caldata_extract "ART" 0x1000 0x2f20
 		ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac)
 		;;
+	engenius,emd1)
+		caldata_extract "0:ART" 0x1000 0x2f20
+		ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr)
+		;;
 	engenius,ens620ext)
 		caldata_extract "ART" 0x1000 0x2f20
 		ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2)
@@ -166,6 +170,10 @@ case "$FIRMWARE" in
 		caldata_extract "ART" 0x5000 0x2f20
 		ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
 		;;
+	engenius,emd1)
+		caldata_extract "0:ART" 0x5000 0x2f20
+		ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) +1)
+		;;
 	engenius,ens620ext)
 		caldata_extract "ART" 0x5000 0x2f20
 		ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3)
diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-emd1.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-emd1.dts
new file mode 100644
index 0000000000..cf4f793f21
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-emd1.dts
@@ -0,0 +1,233 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "EnGenius EMD1";
+	compatible = "engenius,emd1";
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		mdio@90000 {
+			status = "okay";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+			switch_lan_bmp = <0x20>;
+			switch_wan_bmp = <0x00>;
+		};
+
+		edma@c080000 {
+			status = "okay";
+			qcom,num_gmac = <1>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "emd1:white:power";
+			gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan2g {
+			label = "emd1:red:wlan2g";
+			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wlan5g {
+			label = "emd1:blue:wlan5g";
+			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		mesh {
+			label = "emd1:orange:mesh";
+			gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&tlmm {
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pin {
+			function = "blsp_spi0";
+			pins = "gpio54", "gpio55", "gpio56", "gpio57";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		pin_cs {
+			function = "gpio";
+			pins = "gpio54";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition0@0 {
+				label = "0:SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+			partition1@40000 {
+				label = "0:MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+			partition2@60000 {
+				label = "0:QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+			partition3@c0000 {
+				label = "0:CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+			partition4@d0000 {
+				label = "0:DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+			partition5@e0000 {
+				label = "0:APPSBLENV";
+				reg = <0x000e0000 0x00010000>;
+				read-only;
+			};
+			partition6@f0000 {
+				label = "0:APPSBL";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+			partition7@170000 {
+				label = "0:ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+			partition8@180000 {
+				label = "userconfig";
+				reg = <0x00180000 0x00080000>;
+				read-only;
+			};
+			partition9@200000 {
+				compatible = "denx,fit";
+				label = "firmware";
+				reg = <0x200000 0x01e00000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gmac0 {
+	qcom,phy_mdio_addr = <4>;
+	qcom,poll_required = <1>;
+	qcom,forced_speed = <1000>;
+	qcom,forced_duplex = <1>;
+	vlan_tag = <1 0x20>;
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&wifi0 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "EnGenius-EMD1";
+};
+
+&wifi1 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "EnGenius-EMD1";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 41a65280c3..bbe4df9df4 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -278,6 +278,19 @@ define Device/engenius_eap1300
 endef
 TARGET_DEVICES += engenius_eap1300
 
+define Device/engenius_emd1
+	$(call Device/FitImage)
+	DEVICE_VENDOR := EnGenius
+	DEVICE_MODEL := EMD1
+	DEVICE_DTS_CONFIG := config@4
+	SOC := qcom-ipq4018
+	IMAGE_SIZE := 30720k
+	IMAGES := sysupgrade.bin factory.bin
+	IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+	IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += engenius_emd1
+
 define Device/engenius_ens620ext
 	$(call Device/FitImage)
 	DEVICE_VENDOR := EnGenius
diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
index 9c9a31e436..11e775a5dc 100644
--- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,41 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,42 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -20,6 +20,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 +	qcom-ipq4018-cs-w3-wd1200g-eup.dtb \
 +	qcom-ipq4018-ea6350v3.dtb \
 +	qcom-ipq4018-eap1300.dtb \
++	qcom-ipq4018-emd1.dtb \
 +	qcom-ipq4018-ens620ext.dtb \
 +	qcom-ipq4018-ex6100v2.dtb \
 +	qcom-ipq4018-ex6150v2.dtb \