ipq806x: add power regulators support

Patches are cherry-picked from linux-next. We're also adding the
corresponding config option to the kernel.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45729

14 files changed, 1415 insertions, 11 deletions

diff --git a/target/linux/ipq806x/config-3.18 b/target/linux/ipq806x/config-3.18
index d32e9891fb..1e08f36a7b 100644
--- a/target/linux/ipq806x/config-3.18
+++ b/target/linux/ipq806x/config-3.18
@@ -84,7 +84,6 @@ CONFIG_CRC16=y
 # CONFIG_CRC32_SARWATE is not set
 CONFIG_CRC32_SLICEBY8=y
 CONFIG_CROSS_MEMORY_ATTACH=y
-# CONFIG_CRYPTO_DEV_QCE is not set
 # CONFIG_CRYPTO_SHA1_ARM_NEON is not set
 # CONFIG_CRYPTO_SHA512_ARM_NEON is not set
 CONFIG_CRYPTO_XZ=y
@@ -191,6 +190,7 @@ CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_COMPAT=y
 CONFIG_I2C_HELPER_AUTO=y
 CONFIG_I2C_QUP=y
+# CONFIG_IEEE802154 is not set
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_INITRAMFS_SOURCE=""
@@ -211,11 +211,12 @@ CONFIG_LZO_DECOMPRESS=y
 CONFIG_MDIO_BITBANG=y
 CONFIG_MDIO_BOARDINFO=y
 CONFIG_MDIO_GPIO=y
+CONFIG_MFD_QCOM_RPM=y
 # CONFIG_MFD_SPMI_PMIC is not set
+CONFIG_MFD_SYSCON=y
 CONFIG_MIGHT_HAVE_CACHE_L2X0=y
 CONFIG_MIGHT_HAVE_PCI=y
 CONFIG_MIGRATION=y
-# CONFIG_MMC_SDHCI_MSM is not set
 CONFIG_MODULES_USE_ELF_REL=y
 CONFIG_MSM_GCC_8660=y
 CONFIG_MSM_GCC_8960=y
@@ -310,6 +311,7 @@ CONFIG_REGMAP=y
 CONFIG_REGMAP_MMIO=y
 CONFIG_REGULATOR=y
 # CONFIG_REGULATOR_DEBUG is not set
+CONFIG_REGULATOR_QCOM_RPM=y
 # CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
 CONFIG_RESET_CONTROLLER=y
 CONFIG_RFS_ACCEL=y
diff --git a/target/linux/ipq806x/config-4.0 b/target/linux/ipq806x/config-4.0
index 96644cf529..61535da561 100644
--- a/target/linux/ipq806x/config-4.0
+++ b/target/linux/ipq806x/config-4.0
@@ -52,7 +52,6 @@ CONFIG_ARM_THUMB=y
 CONFIG_ARM_UNWIND=y
 CONFIG_ARM_VIRT_EXT=y
 CONFIG_AT803X_PHY=y
-# CONFIG_BATTERY_GAUGE_LTC2941 is not set
 # CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
 CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
 CONFIG_BOUNCE=y
@@ -221,7 +220,7 @@ CONFIG_LZO_DECOMPRESS=y
 CONFIG_MDIO_BITBANG=y
 CONFIG_MDIO_BOARDINFO=y
 CONFIG_MDIO_GPIO=y
-# CONFIG_MFD_QCOM_RPM is not set
+CONFIG_MFD_QCOM_RPM=y
 # CONFIG_MFD_SPMI_PMIC is not set
 CONFIG_MIGHT_HAVE_CACHE_L2X0=y
 CONFIG_MIGHT_HAVE_PCI=y
@@ -323,6 +322,7 @@ CONFIG_REGMAP=y
 CONFIG_REGMAP_MMIO=y
 CONFIG_REGULATOR=y
 # CONFIG_REGULATOR_DEBUG is not set
+CONFIG_REGULATOR_QCOM_RPM=y
 # CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
 CONFIG_RESET_CONTROLLER=y
 CONFIG_RFS_ACCEL=y
@@ -357,7 +357,6 @@ CONFIG_SWCONFIG=y
 CONFIG_SWIOTLB=y
 CONFIG_SWP_EMULATE=y
 CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-# CONFIG_TEGRA_AHB is not set
 CONFIG_THERMAL=y
 # CONFIG_THERMAL_DEFAULT_GOV_FAIR_SHARE is not set
 CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
diff --git a/target/linux/ipq806x/patches-3.18/120-mfd-qcom-rpm-Driver-for-the-Qualcomm-RPM.patch b/target/linux/ipq806x/patches-3.18/120-mfd-qcom-rpm-Driver-for-the-Qualcomm-RPM.patch
new file mode 100644
index 0000000000..d8191422c4
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/120-mfd-qcom-rpm-Driver-for-the-Qualcomm-RPM.patch
@@ -0,0 +1,654 @@
+From 58e214382bdd1eb48c5a3519182bddcb26edabad Mon Sep 17 00:00:00 2001
+From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
+Date: Wed, 26 Nov 2014 13:51:00 -0800
+Subject: [PATCH] mfd: qcom-rpm: Driver for the Qualcomm RPM
+
+Driver for the Resource Power Manager (RPM) found in Qualcomm 8660, 8960
+and 8064 based devices. The driver exposes resources that child drivers
+can operate on; to implementing regulator, clock and bus frequency
+drivers.
+
+Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
+Signed-off-by: Lee Jones <lee.jones@linaro.org>
+---
+ drivers/mfd/Kconfig          |  14 ++
+ drivers/mfd/Makefile         |   1 +
+ drivers/mfd/qcom_rpm.c       | 581 +++++++++++++++++++++++++++++++++++++++++++
+ include/linux/mfd/qcom_rpm.h |  13 +
+ 4 files changed, 609 insertions(+)
+ create mode 100644 drivers/mfd/qcom_rpm.c
+ create mode 100644 include/linux/mfd/qcom_rpm.h
+
+--- a/drivers/mfd/Kconfig
++++ b/drivers/mfd/Kconfig
+@@ -567,6 +567,20 @@ config MFD_PM8921_CORE
+ 	  Say M here if you want to include support for PM8921 chip as a module.
+ 	  This will build a module called "pm8921-core".
+ 
++config MFD_QCOM_RPM
++	tristate "Qualcomm Resource Power Manager (RPM)"
++	depends on ARCH_QCOM && OF
++	help
++	  If you say yes to this option, support will be included for the
++	  Resource Power Manager system found in the Qualcomm 8660, 8960 and
++	  8064 based devices.
++
++	  This is required to access many regulators, clocks and bus
++	  frequencies controlled by the RPM on these devices.
++
++	  Say M here if you want to include support for the Qualcomm RPM as a
++	  module. This will build a module called "qcom_rpm".
++
+ config MFD_SPMI_PMIC
+ 	tristate "Qualcomm SPMI PMICs"
+ 	depends on ARCH_QCOM || COMPILE_TEST
+--- a/drivers/mfd/Makefile
++++ b/drivers/mfd/Makefile
+@@ -153,6 +153,7 @@ obj-$(CONFIG_MFD_SI476X_CORE)	+= si476x-
+ obj-$(CONFIG_MFD_CS5535)	+= cs5535-mfd.o
+ obj-$(CONFIG_MFD_OMAP_USB_HOST)	+= omap-usb-host.o omap-usb-tll.o
+ obj-$(CONFIG_MFD_PM8921_CORE) 	+= pm8921-core.o ssbi.o
++obj-$(CONFIG_MFD_QCOM_RPM)	+= qcom_rpm.o
+ obj-$(CONFIG_MFD_SPMI_PMIC)	+= qcom-spmi-pmic.o
+ obj-$(CONFIG_TPS65911_COMPARATOR)	+= tps65911-comparator.o
+ obj-$(CONFIG_MFD_TPS65090)	+= tps65090.o
+--- /dev/null
++++ b/drivers/mfd/qcom_rpm.c
+@@ -0,0 +1,581 @@
++/*
++ * Copyright (c) 2014, Sony Mobile Communications AB.
++ * Copyright (c) 2013, The Linux Foundation. All rights reserved.
++ * Author: Bjorn Andersson <bjorn.andersson@sonymobile.com>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/of_platform.h>
++#include <linux/io.h>
++#include <linux/interrupt.h>
++#include <linux/mfd/qcom_rpm.h>
++#include <linux/mfd/syscon.h>
++#include <linux/regmap.h>
++
++#include <dt-bindings/mfd/qcom-rpm.h>
++
++struct qcom_rpm_resource {
++	unsigned target_id;
++	unsigned status_id;
++	unsigned select_id;
++	unsigned size;
++};
++
++struct qcom_rpm_data {
++	u32 version;
++	const struct qcom_rpm_resource *resource_table;
++	unsigned n_resources;
++};
++
++struct qcom_rpm {
++	struct device *dev;
++	struct regmap *ipc_regmap;
++	unsigned ipc_offset;
++	unsigned ipc_bit;
++
++	struct completion ack;
++	struct mutex lock;
++
++	void __iomem *status_regs;
++	void __iomem *ctrl_regs;
++	void __iomem *req_regs;
++
++	u32 ack_status;
++
++	const struct qcom_rpm_data *data;
++};
++
++#define RPM_STATUS_REG(rpm, i)	((rpm)->status_regs + (i) * 4)
++#define RPM_CTRL_REG(rpm, i)	((rpm)->ctrl_regs + (i) * 4)
++#define RPM_REQ_REG(rpm, i)	((rpm)->req_regs + (i) * 4)
++
++#define RPM_REQUEST_TIMEOUT	(5 * HZ)
++
++#define RPM_REQUEST_CONTEXT	3
++#define RPM_REQ_SELECT		11
++#define RPM_ACK_CONTEXT		15
++#define RPM_ACK_SELECTOR	23
++#define RPM_SELECT_SIZE		7
++
++#define RPM_NOTIFICATION	BIT(30)
++#define RPM_REJECTED		BIT(31)
++
++#define RPM_SIGNAL		BIT(2)
++
++static const struct qcom_rpm_resource apq8064_rpm_resource_table[] = {
++	[QCOM_RPM_CXO_CLK] =			{ 25, 9, 5, 1 },
++	[QCOM_RPM_PXO_CLK] =			{ 26, 10, 6, 1 },
++	[QCOM_RPM_APPS_FABRIC_CLK] =		{ 27, 11, 8, 1 },
++	[QCOM_RPM_SYS_FABRIC_CLK] =		{ 28, 12, 9, 1 },
++	[QCOM_RPM_MM_FABRIC_CLK] =		{ 29, 13, 10, 1 },
++	[QCOM_RPM_DAYTONA_FABRIC_CLK] =		{ 30, 14, 11, 1 },
++	[QCOM_RPM_SFPB_CLK] =			{ 31, 15, 12, 1 },
++	[QCOM_RPM_CFPB_CLK] =			{ 32, 16, 13, 1 },
++	[QCOM_RPM_MMFPB_CLK] =			{ 33, 17, 14, 1 },
++	[QCOM_RPM_EBI1_CLK] =			{ 34, 18, 16, 1 },
++	[QCOM_RPM_APPS_FABRIC_HALT] =		{ 35, 19, 18, 1 },
++	[QCOM_RPM_APPS_FABRIC_MODE] =		{ 37, 20, 19, 1 },
++	[QCOM_RPM_APPS_FABRIC_IOCTL] =		{ 40, 21, 20, 1 },
++	[QCOM_RPM_APPS_FABRIC_ARB] =		{ 41, 22, 21, 12 },
++	[QCOM_RPM_SYS_FABRIC_HALT] =		{ 53, 23, 22, 1 },
++	[QCOM_RPM_SYS_FABRIC_MODE] =		{ 55, 24, 23, 1 },
++	[QCOM_RPM_SYS_FABRIC_IOCTL] =		{ 58, 25, 24, 1 },
++	[QCOM_RPM_SYS_FABRIC_ARB] =		{ 59, 26, 25, 30 },
++	[QCOM_RPM_MM_FABRIC_HALT] =		{ 89, 27, 26, 1 },
++	[QCOM_RPM_MM_FABRIC_MODE] =		{ 91, 28, 27, 1 },
++	[QCOM_RPM_MM_FABRIC_IOCTL] =		{ 94, 29, 28, 1 },
++	[QCOM_RPM_MM_FABRIC_ARB] =		{ 95, 30, 29, 21 },
++	[QCOM_RPM_PM8921_SMPS1] =		{ 116, 31, 30, 2 },
++	[QCOM_RPM_PM8921_SMPS2] =		{ 118, 33, 31, 2 },
++	[QCOM_RPM_PM8921_SMPS3] =		{ 120, 35, 32, 2 },
++	[QCOM_RPM_PM8921_SMPS4] =		{ 122, 37, 33, 2 },
++	[QCOM_RPM_PM8921_SMPS5] =		{ 124, 39, 34, 2 },
++	[QCOM_RPM_PM8921_SMPS6] =		{ 126, 41, 35, 2 },
++	[QCOM_RPM_PM8921_SMPS7] =		{ 128, 43, 36, 2 },
++	[QCOM_RPM_PM8921_SMPS8] =		{ 130, 45, 37, 2 },
++	[QCOM_RPM_PM8921_LDO1] =		{ 132, 47, 38, 2 },
++	[QCOM_RPM_PM8921_LDO2] =		{ 134, 49, 39, 2 },
++	[QCOM_RPM_PM8921_LDO3] =		{ 136, 51, 40, 2 },
++	[QCOM_RPM_PM8921_LDO4] =		{ 138, 53, 41, 2 },
++	[QCOM_RPM_PM8921_LDO5] =		{ 140, 55, 42, 2 },
++	[QCOM_RPM_PM8921_LDO6] =		{ 142, 57, 43, 2 },
++	[QCOM_RPM_PM8921_LDO7] =		{ 144, 59, 44, 2 },
++	[QCOM_RPM_PM8921_LDO8] =		{ 146, 61, 45, 2 },
++	[QCOM_RPM_PM8921_LDO9] =		{ 148, 63, 46, 2 },
++	[QCOM_RPM_PM8921_LDO10] =		{ 150, 65, 47, 2 },
++	[QCOM_RPM_PM8921_LDO11] =		{ 152, 67, 48, 2 },
++	[QCOM_RPM_PM8921_LDO12] =		{ 154, 69, 49, 2 },
++	[QCOM_RPM_PM8921_LDO13] =		{ 156, 71, 50, 2 },
++	[QCOM_RPM_PM8921_LDO14] =		{ 158, 73, 51, 2 },
++	[QCOM_RPM_PM8921_LDO15] =		{ 160, 75, 52, 2 },
++	[QCOM_RPM_PM8921_LDO16] =		{ 162, 77, 53, 2 },
++	[QCOM_RPM_PM8921_LDO17] =		{ 164, 79, 54, 2 },
++	[QCOM_RPM_PM8921_LDO18] =		{ 166, 81, 55, 2 },
++	[QCOM_RPM_PM8921_LDO19] =		{ 168, 83, 56, 2 },
++	[QCOM_RPM_PM8921_LDO20] =		{ 170, 85, 57, 2 },
++	[QCOM_RPM_PM8921_LDO21] =		{ 172, 87, 58, 2 },
++	[QCOM_RPM_PM8921_LDO22] =		{ 174, 89, 59, 2 },
++	[QCOM_RPM_PM8921_LDO23] =		{ 176, 91, 60, 2 },
++	[QCOM_RPM_PM8921_LDO24] =		{ 178, 93, 61, 2 },
++	[QCOM_RPM_PM8921_LDO25] =		{ 180, 95, 62, 2 },
++	[QCOM_RPM_PM8921_LDO26] =		{ 182, 97, 63, 2 },
++	[QCOM_RPM_PM8921_LDO27] =		{ 184, 99, 64, 2 },
++	[QCOM_RPM_PM8921_LDO28] =		{ 186, 101, 65, 2 },
++	[QCOM_RPM_PM8921_LDO29] =		{ 188, 103, 66, 2 },
++	[QCOM_RPM_PM8921_CLK1] =		{ 190, 105, 67, 2 },
++	[QCOM_RPM_PM8921_CLK2] =		{ 192, 107, 68, 2 },
++	[QCOM_RPM_PM8921_LVS1] =		{ 194, 109, 69, 1 },
++	[QCOM_RPM_PM8921_LVS2] =		{ 195, 110, 70, 1 },
++	[QCOM_RPM_PM8921_LVS3] =		{ 196, 111, 71, 1 },
++	[QCOM_RPM_PM8921_LVS4] =		{ 197, 112, 72, 1 },
++	[QCOM_RPM_PM8921_LVS5] =		{ 198, 113, 73, 1 },
++	[QCOM_RPM_PM8921_LVS6] =		{ 199, 114, 74, 1 },
++	[QCOM_RPM_PM8921_LVS7] =		{ 200, 115, 75, 1 },
++	[QCOM_RPM_PM8821_SMPS1] =		{ 201, 116, 76, 2 },
++	[QCOM_RPM_PM8821_SMPS2] =		{ 203, 118, 77, 2 },
++	[QCOM_RPM_PM8821_LDO1] =		{ 205, 120, 78, 2 },
++	[QCOM_RPM_PM8921_NCP] =			{ 207, 122, 80, 2 },
++	[QCOM_RPM_CXO_BUFFERS] =		{ 209, 124, 81, 1 },
++	[QCOM_RPM_USB_OTG_SWITCH] =		{ 210, 125, 82, 1 },
++	[QCOM_RPM_HDMI_SWITCH] =		{ 211, 126, 83, 1 },
++	[QCOM_RPM_DDR_DMM] =			{ 212, 127, 84, 2 },
++	[QCOM_RPM_VDDMIN_GPIO] =		{ 215, 131, 89, 1 },
++};
++
++static const struct qcom_rpm_data apq8064_template = {
++	.version = 3,
++	.resource_table = apq8064_rpm_resource_table,
++	.n_resources = ARRAY_SIZE(apq8064_rpm_resource_table),
++};
++
++static const struct qcom_rpm_resource msm8660_rpm_resource_table[] = {
++	[QCOM_RPM_CXO_CLK] =			{ 32, 12, 5, 1 },
++	[QCOM_RPM_PXO_CLK] =			{ 33, 13, 6, 1 },
++	[QCOM_RPM_PLL_4] =			{ 34, 14, 7, 1 },
++	[QCOM_RPM_APPS_FABRIC_CLK] =		{ 35, 15, 8, 1 },
++	[QCOM_RPM_SYS_FABRIC_CLK] =		{ 36, 16, 9, 1 },
++	[QCOM_RPM_MM_FABRIC_CLK] =		{ 37, 17, 10, 1 },
++	[QCOM_RPM_DAYTONA_FABRIC_CLK] =		{ 38, 18, 11, 1 },
++	[QCOM_RPM_SFPB_CLK] =			{ 39, 19, 12, 1 },
++	[QCOM_RPM_CFPB_CLK] =			{ 40, 20, 13, 1 },
++	[QCOM_RPM_MMFPB_CLK] =			{ 41, 21, 14, 1 },
++	[QCOM_RPM_SMI_CLK] =			{ 42, 22, 15, 1 },
++	[QCOM_RPM_EBI1_CLK] =			{ 43, 23, 16, 1 },
++	[QCOM_RPM_APPS_L2_CACHE_CTL] =		{ 44, 24, 17, 1 },
++	[QCOM_RPM_APPS_FABRIC_HALT] =		{ 45, 25, 18, 2 },
++	[QCOM_RPM_APPS_FABRIC_MODE] =		{ 47, 26, 19, 3 },
++	[QCOM_RPM_APPS_FABRIC_ARB] =		{ 51, 28, 21, 6 },
++	[QCOM_RPM_SYS_FABRIC_HALT] =		{ 63, 29, 22, 2 },
++	[QCOM_RPM_SYS_FABRIC_MODE] =		{ 65, 30, 23, 3 },
++	[QCOM_RPM_SYS_FABRIC_ARB] =		{ 69, 32, 25, 22 },
++	[QCOM_RPM_MM_FABRIC_HALT] =		{ 105, 33, 26, 2 },
++	[QCOM_RPM_MM_FABRIC_MODE] =		{ 107, 34, 27, 3 },
++	[QCOM_RPM_MM_FABRIC_ARB] =		{ 111, 36, 29, 23 },
++	[QCOM_RPM_PM8901_SMPS0] =		{ 134, 37, 30, 2 },
++	[QCOM_RPM_PM8901_SMPS1] =		{ 136, 39, 31, 2 },
++	[QCOM_RPM_PM8901_SMPS2] =		{ 138, 41, 32, 2 },
++	[QCOM_RPM_PM8901_SMPS3] =		{ 140, 43, 33, 2 },
++	[QCOM_RPM_PM8901_SMPS4] =		{ 142, 45, 34, 2 },
++	[QCOM_RPM_PM8901_LDO0] =		{ 144, 47, 35, 2 },
++	[QCOM_RPM_PM8901_LDO1] =		{ 146, 49, 36, 2 },
++	[QCOM_RPM_PM8901_LDO2] =		{ 148, 51, 37, 2 },
++	[QCOM_RPM_PM8901_LDO3] =		{ 150, 53, 38, 2 },
++	[QCOM_RPM_PM8901_LDO4] =		{ 152, 55, 39, 2 },
++	[QCOM_RPM_PM8901_LDO5] =		{ 154, 57, 40, 2 },
++	[QCOM_RPM_PM8901_LDO6] =		{ 156, 59, 41, 2 },
++	[QCOM_RPM_PM8901_LVS0] =		{ 158, 61, 42, 1 },
++	[QCOM_RPM_PM8901_LVS1] =		{ 159, 62, 43, 1 },
++	[QCOM_RPM_PM8901_LVS2] =		{ 160, 63, 44, 1 },
++	[QCOM_RPM_PM8901_LVS3] =		{ 161, 64, 45, 1 },
++	[QCOM_RPM_PM8901_MVS] =			{ 162, 65, 46, 1 },
++	[QCOM_RPM_PM8058_SMPS0] =		{ 163, 66, 47, 2 },
++	[QCOM_RPM_PM8058_SMPS1] =		{ 165, 68, 48, 2 },
++	[QCOM_RPM_PM8058_SMPS2] =		{ 167, 70, 49, 2 },
++	[QCOM_RPM_PM8058_SMPS3] =		{ 169, 72, 50, 2 },
++	[QCOM_RPM_PM8058_SMPS4] =		{ 171, 74, 51, 2 },
++	[QCOM_RPM_PM8058_LDO0] =		{ 173, 76, 52, 2 },
++	[QCOM_RPM_PM8058_LDO1] =		{ 175, 78, 53, 2 },
++	[QCOM_RPM_PM8058_LDO2] =		{ 177, 80, 54, 2 },
++	[QCOM_RPM_PM8058_LDO3] =		{ 179, 82, 55, 2 },
++	[QCOM_RPM_PM8058_LDO4] =		{ 181, 84, 56, 2 },
++	[QCOM_RPM_PM8058_LDO5] =		{ 183, 86, 57, 2 },
++	[QCOM_RPM_PM8058_LDO6] =		{ 185, 88, 58, 2 },
++	[QCOM_RPM_PM8058_LDO7] =		{ 187, 90, 59, 2 },
++	[QCOM_RPM_PM8058_LDO8] =		{ 189, 92, 60, 2 },
++	[QCOM_RPM_PM8058_LDO9] =		{ 191, 94, 61, 2 },
++	[QCOM_RPM_PM8058_LDO10] =		{ 193, 96, 62, 2 },
++	[QCOM_RPM_PM8058_LDO11] =		{ 195, 98, 63, 2 },
++	[QCOM_RPM_PM8058_LDO12] =		{ 197, 100, 64, 2 },
++	[QCOM_RPM_PM8058_LDO13] =		{ 199, 102, 65, 2 },
++	[QCOM_RPM_PM8058_LDO14] =		{ 201, 104, 66, 2 },
++	[QCOM_RPM_PM8058_LDO15] =		{ 203, 106, 67, 2 },
++	[QCOM_RPM_PM8058_LDO16] =		{ 205, 108, 68, 2 },
++	[QCOM_RPM_PM8058_LDO17] =		{ 207, 110, 69, 2 },
++	[QCOM_RPM_PM8058_LDO18] =		{ 209, 112, 70, 2 },
++	[QCOM_RPM_PM8058_LDO19] =		{ 211, 114, 71, 2 },
++	[QCOM_RPM_PM8058_LDO20] =		{ 213, 116, 72, 2 },
++	[QCOM_RPM_PM8058_LDO21] =		{ 215, 118, 73, 2 },
++	[QCOM_RPM_PM8058_LDO22] =		{ 217, 120, 74, 2 },
++	[QCOM_RPM_PM8058_LDO23] =		{ 219, 122, 75, 2 },
++	[QCOM_RPM_PM8058_LDO24] =		{ 221, 124, 76, 2 },
++	[QCOM_RPM_PM8058_LDO25] =		{ 223, 126, 77, 2 },
++	[QCOM_RPM_PM8058_LVS0] =		{ 225, 128, 78, 1 },
++	[QCOM_RPM_PM8058_LVS1] =		{ 226, 129, 79, 1 },
++	[QCOM_RPM_PM8058_NCP] =			{ 227, 130, 80, 2 },
++	[QCOM_RPM_CXO_BUFFERS] =		{ 229, 132, 81, 1 },
++};
++
++static const struct qcom_rpm_data msm8660_template = {
++	.version = 2,
++	.resource_table = msm8660_rpm_resource_table,
++	.n_resources = ARRAY_SIZE(msm8660_rpm_resource_table),
++};
++
++static const struct qcom_rpm_resource msm8960_rpm_resource_table[] = {
++	[QCOM_RPM_CXO_CLK] =			{ 25, 9, 5, 1 },
++	[QCOM_RPM_PXO_CLK] =			{ 26, 10, 6, 1 },
++	[QCOM_RPM_APPS_FABRIC_CLK] =		{ 27, 11, 8, 1 },
++	[QCOM_RPM_SYS_FABRIC_CLK] =		{ 28, 12, 9, 1 },
++	[QCOM_RPM_MM_FABRIC_CLK] =		{ 29, 13, 10, 1 },
++	[QCOM_RPM_DAYTONA_FABRIC_CLK] =		{ 30, 14, 11, 1 },
++	[QCOM_RPM_SFPB_CLK] =			{ 31, 15, 12, 1 },
++	[QCOM_RPM_CFPB_CLK] =			{ 32, 16, 13, 1 },
++	[QCOM_RPM_MMFPB_CLK] =			{ 33, 17, 14, 1 },
++	[QCOM_RPM_EBI1_CLK] =			{ 34, 18, 16, 1 },
++	[QCOM_RPM_APPS_FABRIC_HALT] =		{ 35, 19, 18, 1 },
++	[QCOM_RPM_APPS_FABRIC_MODE] =		{ 37, 20, 19, 1 },
++	[QCOM_RPM_APPS_FABRIC_IOCTL] =		{ 40, 21, 20, 1 },
++	[QCOM_RPM_APPS_FABRIC_ARB] =		{ 41, 22, 21, 12 },
++	[QCOM_RPM_SYS_FABRIC_HALT] =		{ 53, 23, 22, 1 },
++	[QCOM_RPM_SYS_FABRIC_MODE] =		{ 55, 24, 23, 1 },
++	[QCOM_RPM_SYS_FABRIC_IOCTL] =		{ 58, 25, 24, 1 },
++	[QCOM_RPM_SYS_FABRIC_ARB] =		{ 59, 26, 25, 29 },
++	[QCOM_RPM_MM_FABRIC_HALT] =		{ 88, 27, 26, 1 },
++	[QCOM_RPM_MM_FABRIC_MODE] =		{ 90, 28, 27, 1 },
++	[QCOM_RPM_MM_FABRIC_IOCTL] =		{ 93, 29, 28, 1 },
++	[QCOM_RPM_MM_FABRIC_ARB] =		{ 94, 30, 29, 23 },
++	[QCOM_RPM_PM8921_SMPS1] =		{ 117, 31, 30, 2 },
++	[QCOM_RPM_PM8921_SMPS2] =		{ 119, 33, 31, 2 },
++	[QCOM_RPM_PM8921_SMPS3] =		{ 121, 35, 32, 2 },
++	[QCOM_RPM_PM8921_SMPS4] =		{ 123, 37, 33, 2 },
++	[QCOM_RPM_PM8921_SMPS5] =		{ 125, 39, 34, 2 },
++	[QCOM_RPM_PM8921_SMPS6] =		{ 127, 41, 35, 2 },
++	[QCOM_RPM_PM8921_SMPS7] =		{ 129, 43, 36, 2 },
++	[QCOM_RPM_PM8921_SMPS8] =		{ 131, 45, 37, 2 },
++	[QCOM_RPM_PM8921_LDO1] =		{ 133, 47, 38, 2 },
++	[QCOM_RPM_PM8921_LDO2] =		{ 135, 49, 39, 2 },
++	[QCOM_RPM_PM8921_LDO3] =		{ 137, 51, 40, 2 },
++	[QCOM_RPM_PM8921_LDO4] =		{ 139, 53, 41, 2 },
++	[QCOM_RPM_PM8921_LDO5] =		{ 141, 55, 42, 2 },
++	[QCOM_RPM_PM8921_LDO6] =		{ 143, 57, 43, 2 },
++	[QCOM_RPM_PM8921_LDO7] =		{ 145, 59, 44, 2 },
++	[QCOM_RPM_PM8921_LDO8] =		{ 147, 61, 45, 2 },
++	[QCOM_RPM_PM8921_LDO9] =		{ 149, 63, 46, 2 },
++	[QCOM_RPM_PM8921_LDO10] =		{ 151, 65, 47, 2 },
++	[QCOM_RPM_PM8921_LDO11] =		{ 153, 67, 48, 2 },
++	[QCOM_RPM_PM8921_LDO12] =		{ 155, 69, 49, 2 },
++	[QCOM_RPM_PM8921_LDO13] =		{ 157, 71, 50, 2 },
++	[QCOM_RPM_PM8921_LDO14] =		{ 159, 73, 51, 2 },
++	[QCOM_RPM_PM8921_LDO15] =		{ 161, 75, 52, 2 },
++	[QCOM_RPM_PM8921_LDO16] =		{ 163, 77, 53, 2 },
++	[QCOM_RPM_PM8921_LDO17] =		{ 165, 79, 54, 2 },
++	[QCOM_RPM_PM8921_LDO18] =		{ 167, 81, 55, 2 },
++	[QCOM_RPM_PM8921_LDO19] =		{ 169, 83, 56, 2 },
++	[QCOM_RPM_PM8921_LDO20] =		{ 171, 85, 57, 2 },
++	[QCOM_RPM_PM8921_LDO21] =		{ 173, 87, 58, 2 },
++	[QCOM_RPM_PM8921_LDO22] =		{ 175, 89, 59, 2 },
++	[QCOM_RPM_PM8921_LDO23] =		{ 177, 91, 60, 2 },
++	[QCOM_RPM_PM8921_LDO24] =		{ 179, 93, 61, 2 },
++	[QCOM_RPM_PM8921_LDO25] =		{ 181, 95, 62, 2 },
++	[QCOM_RPM_PM8921_LDO26] =		{ 183, 97, 63, 2 },
++	[QCOM_RPM_PM8921_LDO27] =		{ 185, 99, 64, 2 },
++	[QCOM_RPM_PM8921_LDO28] =		{ 187, 101, 65, 2 },
++	[QCOM_RPM_PM8921_LDO29] =		{ 189, 103, 66, 2 },
++	[QCOM_RPM_PM8921_CLK1] =		{ 191, 105, 67, 2 },
++	[QCOM_RPM_PM8921_CLK2] =		{ 193, 107, 68, 2 },
++	[QCOM_RPM_PM8921_LVS1] =		{ 195, 109, 69, 1 },
++	[QCOM_RPM_PM8921_LVS2] =		{ 196, 110, 70, 1 },
++	[QCOM_RPM_PM8921_LVS3] =		{ 197, 111, 71, 1 },
++	[QCOM_RPM_PM8921_LVS4] =		{ 198, 112, 72, 1 },
++	[QCOM_RPM_PM8921_LVS5] =		{ 199, 113, 73, 1 },
++	[QCOM_RPM_PM8921_LVS6] =		{ 200, 114, 74, 1 },
++	[QCOM_RPM_PM8921_LVS7] =		{ 201, 115, 75, 1 },
++	[QCOM_RPM_PM8921_NCP] =			{ 202, 116, 80, 2 },
++	[QCOM_RPM_CXO_BUFFERS] =		{ 204, 118, 81, 1 },
++	[QCOM_RPM_USB_OTG_SWITCH] =		{ 205, 119, 82, 1 },
++	[QCOM_RPM_HDMI_SWITCH] =		{ 206, 120, 83, 1 },
++	[QCOM_RPM_DDR_DMM] =			{ 207, 121, 84, 2 },
++};
++
++static const struct qcom_rpm_data msm8960_template = {
++	.version = 3,
++	.resource_table = msm8960_rpm_resource_table,
++	.n_resources = ARRAY_SIZE(msm8960_rpm_resource_table),
++};
++
++static const struct of_device_id qcom_rpm_of_match[] = {
++	{ .compatible = "qcom,rpm-apq8064", .data = &apq8064_template },
++	{ .compatible = "qcom,rpm-msm8660", .data = &msm8660_template },
++	{ .compatible = "qcom,rpm-msm8960", .data = &msm8960_template },
++	{ }
++};
++MODULE_DEVICE_TABLE(of, qcom_rpm_of_match);
++
++int qcom_rpm_write(struct qcom_rpm *rpm,
++		   int state,
++		   int resource,
++		   u32 *buf, size_t count)
++{
++	const struct qcom_rpm_resource *res;
++	const struct qcom_rpm_data *data = rpm->data;
++	u32 sel_mask[RPM_SELECT_SIZE] = { 0 };
++	int left;
++	int ret = 0;
++	int i;
++
++	if (WARN_ON(resource < 0 || resource >= data->n_resources))
++		return -EINVAL;
++
++	res = &data->resource_table[resource];
++	if (WARN_ON(res->size != count))
++		return -EINVAL;
++
++	mutex_lock(&rpm->lock);
++
++	for (i = 0; i < res->size; i++)
++		writel_relaxed(buf[i], RPM_REQ_REG(rpm, res->target_id + i));
++
++	bitmap_set((unsigned long *)sel_mask, res->select_id, 1);
++	for (i = 0; i < ARRAY_SIZE(sel_mask); i++) {
++		writel_relaxed(sel_mask[i],
++			       RPM_CTRL_REG(rpm, RPM_REQ_SELECT + i));
++	}
++
++	writel_relaxed(BIT(state), RPM_CTRL_REG(rpm, RPM_REQUEST_CONTEXT));
++
++	reinit_completion(&rpm->ack);
++	regmap_write(rpm->ipc_regmap, rpm->ipc_offset, BIT(rpm->ipc_bit));
++
++	left = wait_for_completion_timeout(&rpm->ack, RPM_REQUEST_TIMEOUT);
++	if (!left)
++		ret = -ETIMEDOUT;
++	else if (rpm->ack_status & RPM_REJECTED)
++		ret = -EIO;
++
++	mutex_unlock(&rpm->lock);
++
++	return ret;
++}
++EXPORT_SYMBOL(qcom_rpm_write);
++
++static irqreturn_t qcom_rpm_ack_interrupt(int irq, void *dev)
++{
++	struct qcom_rpm *rpm = dev;
++	u32 ack;
++	int i;
++
++	ack = readl_relaxed(RPM_CTRL_REG(rpm, RPM_ACK_CONTEXT));
++	for (i = 0; i < RPM_SELECT_SIZE; i++)
++		writel_relaxed(0, RPM_CTRL_REG(rpm, RPM_ACK_SELECTOR + i));
++	writel(0, RPM_CTRL_REG(rpm, RPM_ACK_CONTEXT));
++
++	if (ack & RPM_NOTIFICATION) {
++		dev_warn(rpm->dev, "ignoring notification!\n");
++	} else {
++		rpm->ack_status = ack;
++		complete(&rpm->ack);
++	}
++
++	return IRQ_HANDLED;
++}
++
++static irqreturn_t qcom_rpm_err_interrupt(int irq, void *dev)
++{
++	struct qcom_rpm *rpm = dev;
++
++	regmap_write(rpm->ipc_regmap, rpm->ipc_offset, BIT(rpm->ipc_bit));
++	dev_err(rpm->dev, "RPM triggered fatal error\n");
++
++	return IRQ_HANDLED;
++}
++
++static irqreturn_t qcom_rpm_wakeup_interrupt(int irq, void *dev)
++{
++	return IRQ_HANDLED;
++}
++
++static int qcom_rpm_probe(struct platform_device *pdev)
++{
++	const struct of_device_id *match;
++	struct device_node *syscon_np;
++	struct resource *res;
++	struct qcom_rpm *rpm;
++	u32 fw_version[3];
++	int irq_wakeup;
++	int irq_ack;
++	int irq_err;
++	int ret;
++
++	rpm = devm_kzalloc(&pdev->dev, sizeof(*rpm), GFP_KERNEL);
++	if (!rpm)
++		return -ENOMEM;
++
++	rpm->dev = &pdev->dev;
++	mutex_init(&rpm->lock);
++	init_completion(&rpm->ack);
++
++	irq_ack = platform_get_irq_byname(pdev, "ack");
++	if (irq_ack < 0) {
++		dev_err(&pdev->dev, "required ack interrupt missing\n");
++		return irq_ack;
++	}
++
++	irq_err = platform_get_irq_byname(pdev, "err");
++	if (irq_err < 0) {
++		dev_err(&pdev->dev, "required err interrupt missing\n");
++		return irq_err;
++	}
++
++	irq_wakeup = platform_get_irq_byname(pdev, "wakeup");
++	if (irq_wakeup < 0) {
++		dev_err(&pdev->dev, "required wakeup interrupt missing\n");
++		return irq_wakeup;
++	}
++
++	match = of_match_device(qcom_rpm_of_match, &pdev->dev);
++	rpm->data = match->data;
++
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	rpm->status_regs = devm_ioremap_resource(&pdev->dev, res);
++	if (IS_ERR(rpm->status_regs))
++		return PTR_ERR(rpm->status_regs);
++	rpm->ctrl_regs = rpm->status_regs + 0x400;
++	rpm->req_regs = rpm->status_regs + 0x600;
++
++	syscon_np = of_parse_phandle(pdev->dev.of_node, "qcom,ipc", 0);
++	if (!syscon_np) {
++		dev_err(&pdev->dev, "no qcom,ipc node\n");
++		return -ENODEV;
++	}
++
++	rpm->ipc_regmap = syscon_node_to_regmap(syscon_np);
++	if (IS_ERR(rpm->ipc_regmap))
++		return PTR_ERR(rpm->ipc_regmap);
++
++	ret = of_property_read_u32_index(pdev->dev.of_node, "qcom,ipc", 1,
++					 &rpm->ipc_offset);
++	if (ret < 0) {
++		dev_err(&pdev->dev, "no offset in qcom,ipc\n");
++		return -EINVAL;
++	}
++
++	ret = of_property_read_u32_index(pdev->dev.of_node, "qcom,ipc", 2,
++					 &rpm->ipc_bit);
++	if (ret < 0) {
++		dev_err(&pdev->dev, "no bit in qcom,ipc\n");
++		return -EINVAL;
++	}
++
++	dev_set_drvdata(&pdev->dev, rpm);
++
++	fw_version[0] = readl(RPM_STATUS_REG(rpm, 0));
++	fw_version[1] = readl(RPM_STATUS_REG(rpm, 1));
++	fw_version[2] = readl(RPM_STATUS_REG(rpm, 2));
++	if (fw_version[0] != rpm->data->version) {
++		dev_err(&pdev->dev,
++			"RPM version %u.%u.%u incompatible with driver version %u",
++			fw_version[0],
++			fw_version[1],
++			fw_version[2],
++			rpm->data->version);
++		return -EFAULT;
++	}
++
++	dev_info(&pdev->dev, "RPM firmware %u.%u.%u\n", fw_version[0],
++							fw_version[1],
++							fw_version[2]);
++
++	ret = devm_request_irq(&pdev->dev,
++			       irq_ack,
++			       qcom_rpm_ack_interrupt,
++			       IRQF_TRIGGER_RISING | IRQF_NO_SUSPEND,
++			       "qcom_rpm_ack",
++			       rpm);
++	if (ret) {
++		dev_err(&pdev->dev, "failed to request ack interrupt\n");
++		return ret;
++	}
++
++	ret = irq_set_irq_wake(irq_ack, 1);
++	if (ret)
++		dev_warn(&pdev->dev, "failed to mark ack irq as wakeup\n");
++
++	ret = devm_request_irq(&pdev->dev,
++			       irq_err,
++			       qcom_rpm_err_interrupt,
++			       IRQF_TRIGGER_RISING,
++			       "qcom_rpm_err",
++			       rpm);
++	if (ret) {
++		dev_err(&pdev->dev, "failed to request err interrupt\n");
++		return ret;
++	}
++
++	ret = devm_request_irq(&pdev->dev,
++			       irq_wakeup,
++			       qcom_rpm_wakeup_interrupt,
++			       IRQF_TRIGGER_RISING,
++			       "qcom_rpm_wakeup",
++			       rpm);
++	if (ret) {
++		dev_err(&pdev->dev, "failed to request wakeup interrupt\n");
++		return ret;
++	}
++
++	ret = irq_set_irq_wake(irq_wakeup, 1);
++	if (ret)
++		dev_warn(&pdev->dev, "failed to mark wakeup irq as wakeup\n");
++
++	return of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
++}
++
++static int qcom_rpm_remove(struct platform_device *pdev)
++{
++	of_platform_depopulate(&pdev->dev);
++	return 0;
++}
++
++static struct platform_driver qcom_rpm_driver = {
++	.probe = qcom_rpm_probe,
++	.remove = qcom_rpm_remove,
++	.driver  = {
++		.name  = "qcom_rpm",
++		.of_match_table = qcom_rpm_of_match,
++	},
++};
++
++static int __init qcom_rpm_init(void)
++{
++	return platform_driver_register(&qcom_rpm_driver);
++}
++arch_initcall(qcom_rpm_init);
++
++static void __exit qcom_rpm_exit(void)
++{
++	platform_driver_unregister(&qcom_rpm_driver);
++}
++module_exit(qcom_rpm_exit)
++
++MODULE_DESCRIPTION("Qualcomm Resource Power Manager driver");
++MODULE_LICENSE("GPL v2");
++MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@sonymobile.com>");
+--- /dev/null
++++ b/include/linux/mfd/qcom_rpm.h
+@@ -0,0 +1,13 @@
++#ifndef __QCOM_RPM_H__
++#define __QCOM_RPM_H__
++
++#include <linux/types.h>
++
++struct qcom_rpm;
++
++#define QCOM_RPM_ACTIVE_STATE	0
++#define QCOM_RPM_SLEEP_STATE	1
++
++int qcom_rpm_write(struct qcom_rpm *rpm, int state, int resource, u32 *buf, size_t count);
++
++#endif
diff --git a/target/linux/ipq806x/patches-3.18/121-mfd-qcom_rpm-Add-support-for-IPQ8064.patch b/target/linux/ipq806x/patches-3.18/121-mfd-qcom_rpm-Add-support-for-IPQ8064.patch
new file mode 100644
index 0000000000..e5e9e4e6cc
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/121-mfd-qcom_rpm-Add-support-for-IPQ8064.patch
@@ -0,0 +1,71 @@
+From 4d54b0adfa67476e6509bc8646b9dbac642e8a29 Mon Sep 17 00:00:00 2001
+From: Josh Cartwright <joshc@codeaurora.org>
+Date: Thu, 26 Mar 2015 11:29:26 -0700
+Subject: [PATCH] mfd: qcom_rpm: Add support for IPQ8064
+
+The IPQ8064 also includes an RPM following the same message structure as
+other chips.  In addition, it supports a few new resource types to
+support the NSS fabric clocks and the SMB208/SMB209 regulators found on
+the reference boards.
+
+Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
+Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
+Signed-off-by: Lee Jones <lee.jones@linaro.org>
+---
+ drivers/mfd/qcom_rpm.c | 41 +++++++++++++++++++++++++++++++++++++++++
+ 1 file changed, 41 insertions(+)
+
+--- a/drivers/mfd/qcom_rpm.c
++++ b/drivers/mfd/qcom_rpm.c
+@@ -323,10 +323,51 @@ static const struct qcom_rpm_data msm896
+ 	.n_resources = ARRAY_SIZE(msm8960_rpm_resource_table),
+ };
+ 
++static const struct qcom_rpm_resource ipq806x_rpm_resource_table[] = {
++	[QCOM_RPM_CXO_CLK] =			{ 25, 9, 5, 1 },
++	[QCOM_RPM_PXO_CLK] =			{ 26, 10, 6, 1 },
++	[QCOM_RPM_APPS_FABRIC_CLK] =		{ 27, 11, 8, 1 },
++	[QCOM_RPM_SYS_FABRIC_CLK] =		{ 28, 12, 9, 1 },
++	[QCOM_RPM_NSS_FABRIC_0_CLK] =		{ 29, 13, 10, 1 },
++	[QCOM_RPM_DAYTONA_FABRIC_CLK] =		{ 30, 14, 11, 1 },
++	[QCOM_RPM_SFPB_CLK] =			{ 31, 15, 12, 1 },
++	[QCOM_RPM_CFPB_CLK] =			{ 32, 16, 13, 1 },
++	[QCOM_RPM_NSS_FABRIC_1_CLK] =		{ 33, 17, 14, 1 },
++	[QCOM_RPM_EBI1_CLK] =			{ 34, 18, 16, 1 },
++	[QCOM_RPM_APPS_FABRIC_HALT] =		{ 35, 19, 18, 2 },
++	[QCOM_RPM_APPS_FABRIC_MODE] =		{ 37, 20, 19, 3 },
++	[QCOM_RPM_APPS_FABRIC_IOCTL] =		{ 40, 21, 20, 1 },
++	[QCOM_RPM_APPS_FABRIC_ARB] =		{ 41, 22, 21, 12 },
++	[QCOM_RPM_SYS_FABRIC_HALT] =		{ 53, 23, 22, 2 },
++	[QCOM_RPM_SYS_FABRIC_MODE] =		{ 55, 24, 23, 3 },
++	[QCOM_RPM_SYS_FABRIC_IOCTL] =		{ 58, 25, 24, 1 },
++	[QCOM_RPM_SYS_FABRIC_ARB] =		{ 59, 26, 25, 30 },
++	[QCOM_RPM_MM_FABRIC_HALT] =		{ 89, 27, 26, 2 },
++	[QCOM_RPM_MM_FABRIC_MODE] =		{ 91, 28, 27, 3 },
++	[QCOM_RPM_MM_FABRIC_IOCTL] =		{ 94, 29, 28, 1 },
++	[QCOM_RPM_MM_FABRIC_ARB] =		{ 95, 30, 29, 2 },
++	[QCOM_RPM_CXO_BUFFERS] =		{ 209, 33, 31, 1 },
++	[QCOM_RPM_USB_OTG_SWITCH] =		{ 210, 34, 32, 1 },
++	[QCOM_RPM_HDMI_SWITCH] =		{ 211, 35, 33, 1 },
++	[QCOM_RPM_DDR_DMM] =			{ 212, 36, 34, 2 },
++	[QCOM_RPM_VDDMIN_GPIO] =		{ 215, 40, 39, 1 },
++	[QCOM_RPM_SMB208_S1a] =			{ 216, 41, 90, 2 },
++	[QCOM_RPM_SMB208_S1b] =			{ 218, 43, 91, 2 },
++	[QCOM_RPM_SMB208_S2a] =			{ 220, 45, 92, 2 },
++	[QCOM_RPM_SMB208_S2b] =			{ 222, 47, 93, 2 },
++};
++
++static const struct qcom_rpm_data ipq806x_template = {
++	.version = 3,
++	.resource_table = ipq806x_rpm_resource_table,
++	.n_resources = ARRAY_SIZE(ipq806x_rpm_resource_table),
++};
++
+ static const struct of_device_id qcom_rpm_of_match[] = {
+ 	{ .compatible = "qcom,rpm-apq8064", .data = &apq8064_template },
+ 	{ .compatible = "qcom,rpm-msm8660", .data = &msm8660_template },
+ 	{ .compatible = "qcom,rpm-msm8960", .data = &msm8960_template },
++	{ .compatible = "qcom,rpm-ipq8064", .data = &ipq806x_template },
+ 	{ }
+ };
+ MODULE_DEVICE_TABLE(of, qcom_rpm_of_match);
diff --git a/target/linux/ipq806x/patches-3.18/122-mfd-devicetree-bindings-Add-Qualcomm-RPM-DT-binding.patch b/target/linux/ipq806x/patches-3.18/122-mfd-devicetree-bindings-Add-Qualcomm-RPM-DT-binding.patch
new file mode 100644
index 0000000000..bb730f8752
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/122-mfd-devicetree-bindings-Add-Qualcomm-RPM-DT-binding.patch
@@ -0,0 +1,256 @@
+From aa0c4b815045420ea54d5ae5362f5a0190609d46 Mon Sep 17 00:00:00 2001
+From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
+Date: Wed, 26 Nov 2014 13:50:59 -0800
+Subject: [PATCH] mfd: devicetree: bindings: Add Qualcomm RPM DT binding
+
+Add binding for the Qualcomm Resource Power Manager (RPM) found in 8660,
+8960 and 8064 based devices.
+
+Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
+Signed-off-by: Lee Jones <lee.jones@linaro.org>
+---
+ Documentation/devicetree/bindings/mfd/qcom-rpm.txt |  70 ++++++++++
+ include/dt-bindings/mfd/qcom-rpm.h                 | 154 +++++++++++++++++++++
+ 2 files changed, 224 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/mfd/qcom-rpm.txt
+ create mode 100644 include/dt-bindings/mfd/qcom-rpm.h
+
+diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
+new file mode 100644
+index 0000000..85e3198
+--- /dev/null
++++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
+@@ -0,0 +1,70 @@
++Qualcomm Resource Power Manager (RPM)
++
++This driver is used to interface with the Resource Power Manager (RPM) found in
++various Qualcomm platforms. The RPM allows each component in the system to vote
++for state of the system resources, such as clocks, regulators and bus
++frequencies.
++
++- compatible:
++	Usage: required
++	Value type: <string>
++	Definition: must be one of:
++		    "qcom,rpm-apq8064"
++		    "qcom,rpm-msm8660"
++		    "qcom,rpm-msm8960"
++
++- reg:
++	Usage: required
++	Value type: <prop-encoded-array>
++	Definition: base address and size of the RPM's message ram
++
++- interrupts:
++	Usage: required
++	Value type: <prop-encoded-array>
++	Definition: three entries specifying the RPM's:
++		    1. acknowledgement interrupt
++		    2. error interrupt
++		    3. wakeup interrupt
++
++- interrupt-names:
++	Usage: required
++	Value type: <string-array>
++	Definition: must be the three strings "ack", "err" and "wakeup", in order
++
++- #address-cells:
++	Usage: required
++	Value type: <u32>
++	Definition: must be 1
++
++- #size-cells:
++	Usage: required
++	Value type: <u32>
++	Definition: must be 0
++
++- qcom,ipc:
++	Usage: required
++	Value type: <prop-encoded-array>
++
++	Definition: three entries specifying the outgoing ipc bit used for
++		    signaling the RPM:
++		    - phandle to a syscon node representing the apcs registers
++		    - u32 representing offset to the register within the syscon
++		    - u32 representing the ipc bit within the register
++
++
++= EXAMPLE
++
++	#include <dt-bindings/mfd/qcom-rpm.h>
++
++	rpm@108000 {
++		compatible = "qcom,rpm-msm8960";
++		reg = <0x108000 0x1000>;
++		qcom,ipc = <&apcs 0x8 2>;
++
++		interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
++		interrupt-names = "ack", "err", "wakeup";
++
++		#address-cells = <1>;
++		#size-cells = <0>;
++	};
++
+diff --git a/include/dt-bindings/mfd/qcom-rpm.h b/include/dt-bindings/mfd/qcom-rpm.h
+new file mode 100644
+index 0000000..388a6f3
+--- /dev/null
++++ b/include/dt-bindings/mfd/qcom-rpm.h
+@@ -0,0 +1,154 @@
++/*
++ * This header provides constants for the Qualcomm RPM bindings.
++ */
++
++#ifndef _DT_BINDINGS_MFD_QCOM_RPM_H
++#define _DT_BINDINGS_MFD_QCOM_RPM_H
++
++/*
++ * Constants use to identify individual resources in the RPM.
++ */
++#define QCOM_RPM_APPS_FABRIC_ARB		1
++#define QCOM_RPM_APPS_FABRIC_CLK		2
++#define QCOM_RPM_APPS_FABRIC_HALT		3
++#define QCOM_RPM_APPS_FABRIC_IOCTL		4
++#define QCOM_RPM_APPS_FABRIC_MODE		5
++#define QCOM_RPM_APPS_L2_CACHE_CTL		6
++#define QCOM_RPM_CFPB_CLK			7
++#define QCOM_RPM_CXO_BUFFERS			8
++#define QCOM_RPM_CXO_CLK			9
++#define QCOM_RPM_DAYTONA_FABRIC_CLK		10
++#define QCOM_RPM_DDR_DMM			11
++#define QCOM_RPM_EBI1_CLK			12
++#define QCOM_RPM_HDMI_SWITCH			13
++#define QCOM_RPM_MMFPB_CLK			14
++#define QCOM_RPM_MM_FABRIC_ARB			15
++#define QCOM_RPM_MM_FABRIC_CLK			16
++#define QCOM_RPM_MM_FABRIC_HALT			17
++#define QCOM_RPM_MM_FABRIC_IOCTL		18
++#define QCOM_RPM_MM_FABRIC_MODE			19
++#define QCOM_RPM_PLL_4				20
++#define QCOM_RPM_PM8058_LDO0			21
++#define QCOM_RPM_PM8058_LDO1			22
++#define QCOM_RPM_PM8058_LDO2			23
++#define QCOM_RPM_PM8058_LDO3			24
++#define QCOM_RPM_PM8058_LDO4			25
++#define QCOM_RPM_PM8058_LDO5			26
++#define QCOM_RPM_PM8058_LDO6			27
++#define QCOM_RPM_PM8058_LDO7			28
++#define QCOM_RPM_PM8058_LDO8			29
++#define QCOM_RPM_PM8058_LDO9			30
++#define QCOM_RPM_PM8058_LDO10			31
++#define QCOM_RPM_PM8058_LDO11			32
++#define QCOM_RPM_PM8058_LDO12			33
++#define QCOM_RPM_PM8058_LDO13			34
++#define QCOM_RPM_PM8058_LDO14			35
++#define QCOM_RPM_PM8058_LDO15			36
++#define QCOM_RPM_PM8058_LDO16			37
++#define QCOM_RPM_PM8058_LDO17			38
++#define QCOM_RPM_PM8058_LDO18			39
++#define QCOM_RPM_PM8058_LDO19			40
++#define QCOM_RPM_PM8058_LDO20			41
++#define QCOM_RPM_PM8058_LDO21			42
++#define QCOM_RPM_PM8058_LDO22			43
++#define QCOM_RPM_PM8058_LDO23			44
++#define QCOM_RPM_PM8058_LDO24			45
++#define QCOM_RPM_PM8058_LDO25			46
++#define QCOM_RPM_PM8058_LVS0			47
++#define QCOM_RPM_PM8058_LVS1			48
++#define QCOM_RPM_PM8058_NCP			49
++#define QCOM_RPM_PM8058_SMPS0			50
++#define QCOM_RPM_PM8058_SMPS1			51
++#define QCOM_RPM_PM8058_SMPS2			52
++#define QCOM_RPM_PM8058_SMPS3			53
++#define QCOM_RPM_PM8058_SMPS4			54
++#define QCOM_RPM_PM8821_LDO1			55
++#define QCOM_RPM_PM8821_SMPS1			56
++#define QCOM_RPM_PM8821_SMPS2			57
++#define QCOM_RPM_PM8901_LDO0			58
++#define QCOM_RPM_PM8901_LDO1			59
++#define QCOM_RPM_PM8901_LDO2			60
++#define QCOM_RPM_PM8901_LDO3			61
++#define QCOM_RPM_PM8901_LDO4			62
++#define QCOM_RPM_PM8901_LDO5			63
++#define QCOM_RPM_PM8901_LDO6			64
++#define QCOM_RPM_PM8901_LVS0			65
++#define QCOM_RPM_PM8901_LVS1			66
++#define QCOM_RPM_PM8901_LVS2			67
++#define QCOM_RPM_PM8901_LVS3			68
++#define QCOM_RPM_PM8901_MVS			69
++#define QCOM_RPM_PM8901_SMPS0			70
++#define QCOM_RPM_PM8901_SMPS1			71
++#define QCOM_RPM_PM8901_SMPS2			72
++#define QCOM_RPM_PM8901_SMPS3			73
++#define QCOM_RPM_PM8901_SMPS4			74
++#define QCOM_RPM_PM8921_CLK1			75
++#define QCOM_RPM_PM8921_CLK2			76
++#define QCOM_RPM_PM8921_LDO1			77
++#define QCOM_RPM_PM8921_LDO2			78
++#define QCOM_RPM_PM8921_LDO3			79
++#define QCOM_RPM_PM8921_LDO4			80
++#define QCOM_RPM_PM8921_LDO5			81
++#define QCOM_RPM_PM8921_LDO6			82
++#define QCOM_RPM_PM8921_LDO7			83
++#define QCOM_RPM_PM8921_LDO8			84
++#define QCOM_RPM_PM8921_LDO9			85
++#define QCOM_RPM_PM8921_LDO10			86
++#define QCOM_RPM_PM8921_LDO11			87
++#define QCOM_RPM_PM8921_LDO12			88
++#define QCOM_RPM_PM8921_LDO13			89
++#define QCOM_RPM_PM8921_LDO14			90
++#define QCOM_RPM_PM8921_LDO15			91
++#define QCOM_RPM_PM8921_LDO16			92
++#define QCOM_RPM_PM8921_LDO17			93
++#define QCOM_RPM_PM8921_LDO18			94
++#define QCOM_RPM_PM8921_LDO19			95
++#define QCOM_RPM_PM8921_LDO20			96
++#define QCOM_RPM_PM8921_LDO21			97
++#define QCOM_RPM_PM8921_LDO22			98
++#define QCOM_RPM_PM8921_LDO23			99
++#define QCOM_RPM_PM8921_LDO24			100
++#define QCOM_RPM_PM8921_LDO25			101
++#define QCOM_RPM_PM8921_LDO26			102
++#define QCOM_RPM_PM8921_LDO27			103
++#define QCOM_RPM_PM8921_LDO28			104
++#define QCOM_RPM_PM8921_LDO29			105
++#define QCOM_RPM_PM8921_LVS1			106
++#define QCOM_RPM_PM8921_LVS2			107
++#define QCOM_RPM_PM8921_LVS3			108
++#define QCOM_RPM_PM8921_LVS4			109
++#define QCOM_RPM_PM8921_LVS5			110
++#define QCOM_RPM_PM8921_LVS6			111
++#define QCOM_RPM_PM8921_LVS7			112
++#define QCOM_RPM_PM8921_MVS			113
++#define QCOM_RPM_PM8921_NCP			114
++#define QCOM_RPM_PM8921_SMPS1			115
++#define QCOM_RPM_PM8921_SMPS2			116
++#define QCOM_RPM_PM8921_SMPS3			117
++#define QCOM_RPM_PM8921_SMPS4			118
++#define QCOM_RPM_PM8921_SMPS5			119
++#define QCOM_RPM_PM8921_SMPS6			120
++#define QCOM_RPM_PM8921_SMPS7			121
++#define QCOM_RPM_PM8921_SMPS8			122
++#define QCOM_RPM_PXO_CLK			123
++#define QCOM_RPM_QDSS_CLK			124
++#define QCOM_RPM_SFPB_CLK			125
++#define QCOM_RPM_SMI_CLK			126
++#define QCOM_RPM_SYS_FABRIC_ARB			127
++#define QCOM_RPM_SYS_FABRIC_CLK			128
++#define QCOM_RPM_SYS_FABRIC_HALT		129
++#define QCOM_RPM_SYS_FABRIC_IOCTL		130
++#define QCOM_RPM_SYS_FABRIC_MODE		131
++#define QCOM_RPM_USB_OTG_SWITCH			132
++#define QCOM_RPM_VDDMIN_GPIO			133
++
++/*
++ * Constants used to select force mode for regulators.
++ */
++#define QCOM_RPM_FORCE_MODE_NONE		0
++#define QCOM_RPM_FORCE_MODE_LPM			1
++#define QCOM_RPM_FORCE_MODE_HPM			2
++#define QCOM_RPM_FORCE_MODE_AUTO		3
++#define QCOM_RPM_FORCE_MODE_BYPASS		4
++
++#endif
+-- 
+2.1.4
+
diff --git a/target/linux/ipq806x/patches-3.18/123-mfd-devicetree-qcom_rpm-Document-IPQ8064-resources.patch b/target/linux/ipq806x/patches-3.18/123-mfd-devicetree-qcom_rpm-Document-IPQ8064-resources.patch
new file mode 100644
index 0000000000..c8a9f3f5d0
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/123-mfd-devicetree-qcom_rpm-Document-IPQ8064-resources.patch
@@ -0,0 +1,42 @@
+From 30bc3aa5c4ed3072bdff7d915772df1b91307ed4 Mon Sep 17 00:00:00 2001
+From: Josh Cartwright <joshc@codeaurora.org>
+Date: Thu, 26 Mar 2015 11:29:25 -0700
+Subject: [PATCH] mfd: devicetree: qcom_rpm: Document IPQ8064 resources
+
+The IPQ8064 SoC has several RPM-controlled resources, an NSS fabrick
+clock and four regulator resources.  Provide definitions for them.
+
+Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
+[sboyd@codeaurora.org: Drop regulator part of binding]
+Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
+Signed-off-by: Lee Jones <lee.jones@linaro.org>
+---
+ Documentation/devicetree/bindings/mfd/qcom-rpm.txt | 1 +
+ include/dt-bindings/mfd/qcom-rpm.h                 | 6 ++++++
+ 2 files changed, 7 insertions(+)
+
+--- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
++++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
+@@ -12,6 +12,7 @@ frequencies.
+ 		    "qcom,rpm-apq8064"
+ 		    "qcom,rpm-msm8660"
+ 		    "qcom,rpm-msm8960"
++		    "qcom,rpm-ipq8064"
+ 
+ - reg:
+ 	Usage: required
+--- a/include/dt-bindings/mfd/qcom-rpm.h
++++ b/include/dt-bindings/mfd/qcom-rpm.h
+@@ -141,6 +141,12 @@
+ #define QCOM_RPM_SYS_FABRIC_MODE		131
+ #define QCOM_RPM_USB_OTG_SWITCH			132
+ #define QCOM_RPM_VDDMIN_GPIO			133
++#define QCOM_RPM_NSS_FABRIC_0_CLK		134
++#define QCOM_RPM_NSS_FABRIC_1_CLK		135
++#define QCOM_RPM_SMB208_S1a			136
++#define QCOM_RPM_SMB208_S1b			137
++#define QCOM_RPM_SMB208_S2a			138
++#define QCOM_RPM_SMB208_S2b			139
+ 
+ /*
+  * Constants used to select force mode for regulators.
diff --git a/target/linux/ipq806x/patches-3.18/124-regulator-rpm-add-support-for-RPM-controller-SMB208.patch b/target/linux/ipq806x/patches-3.18/124-regulator-rpm-add-support-for-RPM-controller-SMB208.patch
new file mode 100644
index 0000000000..c411c1ce84
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/124-regulator-rpm-add-support-for-RPM-controller-SMB208.patch
@@ -0,0 +1,63 @@
+From 0f5bb5b5de3b18877373f746bdb85d8ea0efeedf Mon Sep 17 00:00:00 2001
+From: Josh Cartwright <joshc@codeaurora.org>
+Date: Thu, 20 Nov 2014 13:41:25 -0600
+Subject: [PATCH] regulator: rpm: add support for RPM-controller SMB208
+
+The IPQ8064 reference boards make use of SMB208 regulators which are
+controlled by RPM.  Implement support for these regulators in the RPM
+regulator driver.
+
+Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
+Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
+Signed-off-by: Mark Brown <broonie@kernel.org>
+---
+ drivers/regulator/qcom_rpm-regulator.c | 19 +++++++++++++++++++
+ 1 file changed, 19 insertions(+)
+
+diff --git a/drivers/regulator/qcom_rpm-regulator.c b/drivers/regulator/qcom_rpm-regulator.c
+index b55cd5b..fbcbd3f 100644
+--- a/drivers/regulator/qcom_rpm-regulator.c
++++ b/drivers/regulator/qcom_rpm-regulator.c
+@@ -183,6 +183,13 @@ static const struct regulator_linear_range ftsmps_ranges[] = {
+ 	REGULATOR_LINEAR_RANGE(1500000,  64, 100, 50000),
+ };
+ 
++static const struct regulator_linear_range smb208_ranges[] = {
++	REGULATOR_LINEAR_RANGE( 375000,   0,  29, 12500),
++	REGULATOR_LINEAR_RANGE( 750000,  30,  89, 12500),
++	REGULATOR_LINEAR_RANGE(1500000,  90, 153, 25000),
++	REGULATOR_LINEAR_RANGE(3100000, 154, 234, 25000),
++};
++
+ static const struct regulator_linear_range ncp_ranges[] = {
+ 	REGULATOR_LINEAR_RANGE(1500000,   0,  31, 50000),
+ };
+@@ -559,6 +566,16 @@ static const struct qcom_rpm_reg pm8921_switch = {
+ 	.parts = &rpm8960_switch_parts,
+ };
+ 
++static const struct qcom_rpm_reg smb208_smps = {
++	.desc.linear_ranges = smb208_ranges,
++	.desc.n_linear_ranges = ARRAY_SIZE(smb208_ranges),
++	.desc.n_voltages = 235,
++	.desc.ops = &uV_ops,
++	.parts = &rpm8960_smps_parts,
++	.supports_force_mode_auto = false,
++	.supports_force_mode_bypass = false,
++};
++
+ static const struct of_device_id rpm_of_match[] = {
+ 	{ .compatible = "qcom,rpm-pm8058-pldo",     .data = &pm8058_pldo },
+ 	{ .compatible = "qcom,rpm-pm8058-nldo",     .data = &pm8058_nldo },
+@@ -578,6 +595,8 @@ static const struct of_device_id rpm_of_match[] = {
+ 	{ .compatible = "qcom,rpm-pm8921-ftsmps",   .data = &pm8921_ftsmps },
+ 	{ .compatible = "qcom,rpm-pm8921-ncp",      .data = &pm8921_ncp },
+ 	{ .compatible = "qcom,rpm-pm8921-switch",   .data = &pm8921_switch },
++
++	{ .compatible = "qcom,rpm-smb208", .data = &smb208_smps },
+ 	{ }
+ };
+ MODULE_DEVICE_TABLE(of, rpm_of_match);
+-- 
+2.1.4
+
diff --git a/target/linux/ipq806x/patches-3.18/125-regulator-qcom-rpm-Add-missing-state-flag-in-call-to.patch b/target/linux/ipq806x/patches-3.18/125-regulator-qcom-rpm-Add-missing-state-flag-in-call-to.patch
new file mode 100644
index 0000000000..11a296af70
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/125-regulator-qcom-rpm-Add-missing-state-flag-in-call-to.patch
@@ -0,0 +1,30 @@
+From 803926825fa4db007437f76654e3e63bafb9b906 Mon Sep 17 00:00:00 2001
+From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
+Date: Wed, 26 Nov 2014 13:51:01 -0800
+Subject: [PATCH] regulator: qcom-rpm: Add missing state flag in call to RPM
+
+This adds the missing state parameter to the call down to the RPM. This
+is currently hard coded to the active state, as that's all we're
+supporting at this moment.
+
+Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
+Signed-off-by: Lee Jones <lee.jones@linaro.org>
+---
+ drivers/regulator/qcom_rpm-regulator.c | 1 +
+ 1 file changed, 1 insertion(+)
+
+diff --git a/drivers/regulator/qcom_rpm-regulator.c b/drivers/regulator/qcom_rpm-regulator.c
+index 8364ff3..edd0a17 100644
+--- a/drivers/regulator/qcom_rpm-regulator.c
++++ b/drivers/regulator/qcom_rpm-regulator.c
+@@ -205,6 +205,7 @@ static int rpm_reg_write(struct qcom_rpm_reg *vreg,
+ 	vreg->val[req->word] |= value << req->shift;
+ 
+ 	return qcom_rpm_write(vreg->rpm,
++			      QCOM_RPM_ACTIVE_STATE,
+ 			      vreg->resource,
+ 			      vreg->val,
+ 			      vreg->parts->request_len);
+-- 
+2.1.4
+
diff --git a/target/linux/ipq806x/patches-3.18/126-add-rpm-to-ipq8064-dts.patch b/target/linux/ipq806x/patches-3.18/126-add-rpm-to-ipq8064-dts.patch
new file mode 100644
index 0000000000..854131c7f6
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/126-add-rpm-to-ipq8064-dts.patch
@@ -0,0 +1,87 @@
+--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
+@@ -2,6 +2,7 @@
+ 
+ #include "skeleton.dtsi"
+ #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
++#include <dt-bindings/mfd/qcom-rpm.h>
+ #include <dt-bindings/soc/qcom,gsbi.h>
+ #include <dt-bindings/reset/qcom,gcc-ipq806x.h>
+ 
+@@ -75,6 +76,63 @@
+ 		ranges;
+ 		compatible = "simple-bus";
+ 
++		rpm@108000 {
++			compatible = "qcom,rpm-ipq8064";
++			reg = <0x108000 0x1000>;
++			qcom,ipc = <&l2cc 0x8 2>;
++
++			interrupts = <0 19 0>,
++				     <0 21 0>,
++				     <0 22 0>;
++			interrupt-names = "ack",
++					  "err",
++					  "wakeup";
++
++			#address-cells = <1>;
++			#size-cells = <0>;
++
++			smb208_s1a: smb208-s1a {
++				compatible = "qcom,rpm-smb208";
++				reg = <QCOM_RPM_SMB208_S1a>;
++
++				regulator-min-microvolt = <1050000>;
++				regulator-max-microvolt = <1150000>;
++
++				qcom,switch-mode-frequency = <1200000>;
++
++			};
++
++			smb208_s1b: smb208-s1b {
++				compatible = "qcom,rpm-smb208";
++				reg = <QCOM_RPM_SMB208_S1b>;
++
++				regulator-min-microvolt = <1050000>;
++				regulator-max-microvolt = <1150000>;
++
++				qcom,switch-mode-frequency = <1200000>;
++			};
++
++			smb208_s2a: smb208-s2a {
++				compatible = "qcom,rpm-smb208";
++				reg = <QCOM_RPM_SMB208_S2a>;
++
++				regulator-min-microvolt = < 800000>;
++				regulator-max-microvolt = <1250000>;
++
++				qcom,switch-mode-frequency = <1200000>;
++			};
++
++			smb208_s2b: smb208-s2b {
++				compatible = "qcom,rpm-smb208";
++				reg = <QCOM_RPM_SMB208_S2b>;
++
++				regulator-min-microvolt = < 800000>;
++				regulator-max-microvolt = <1250000>;
++
++				qcom,switch-mode-frequency = <1200000>;
++			};
++		};
++
+ 		qcom_pinmux: pinmux@800000 {
+ 			compatible = "qcom,ipq8064-pinctrl";
+ 			reg = <0x800000 0x4000>;
+@@ -119,6 +177,12 @@
+ 			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+ 		};
+ 
++		l2cc: clock-controller@2011000 {
++			compatible = "qcom,kpss-gcc", "syscon";
++			reg = <0x2011000 0x1000>;
++			clock-output-names = "acpu_l2_aux";
++ 		};
++ 
+ 		saw0: regulator@2089000 {
+ 			compatible = "qcom,saw2";
+ 			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
diff --git a/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch b/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch
index 4e8f8591f9..2981da6785 100644
--- a/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch
+++ b/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch
@@ -119,15 +119,15 @@
  };
 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
 +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -4,6 +4,7 @@
- #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
+@@ -5,6 +5,7 @@
+ #include <dt-bindings/mfd/qcom-rpm.h>
  #include <dt-bindings/soc/qcom,gsbi.h>
  #include <dt-bindings/reset/qcom,gcc-ipq806x.h>
 +#include <dt-bindings/interrupt-controller/arm-gic.h>
  
  / {
  	model = "Qualcomm IPQ8064";
-@@ -513,5 +514,42 @@
+@@ -577,5 +578,42 @@
  				dr_mode = "host";
  			};
  		};
diff --git a/target/linux/ipq806x/patches-4.0/121-mfd-qcom_rpm-Add-support-for-IPQ8064.patch b/target/linux/ipq806x/patches-4.0/121-mfd-qcom_rpm-Add-support-for-IPQ8064.patch
new file mode 100644
index 0000000000..e5e9e4e6cc
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/121-mfd-qcom_rpm-Add-support-for-IPQ8064.patch
@@ -0,0 +1,71 @@
+From 4d54b0adfa67476e6509bc8646b9dbac642e8a29 Mon Sep 17 00:00:00 2001
+From: Josh Cartwright <joshc@codeaurora.org>
+Date: Thu, 26 Mar 2015 11:29:26 -0700
+Subject: [PATCH] mfd: qcom_rpm: Add support for IPQ8064
+
+The IPQ8064 also includes an RPM following the same message structure as
+other chips.  In addition, it supports a few new resource types to
+support the NSS fabric clocks and the SMB208/SMB209 regulators found on
+the reference boards.
+
+Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
+Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
+Signed-off-by: Lee Jones <lee.jones@linaro.org>
+---
+ drivers/mfd/qcom_rpm.c | 41 +++++++++++++++++++++++++++++++++++++++++
+ 1 file changed, 41 insertions(+)
+
+--- a/drivers/mfd/qcom_rpm.c
++++ b/drivers/mfd/qcom_rpm.c
+@@ -323,10 +323,51 @@ static const struct qcom_rpm_data msm896
+ 	.n_resources = ARRAY_SIZE(msm8960_rpm_resource_table),
+ };
+ 
++static const struct qcom_rpm_resource ipq806x_rpm_resource_table[] = {
++	[QCOM_RPM_CXO_CLK] =			{ 25, 9, 5, 1 },
++	[QCOM_RPM_PXO_CLK] =			{ 26, 10, 6, 1 },
++	[QCOM_RPM_APPS_FABRIC_CLK] =		{ 27, 11, 8, 1 },
++	[QCOM_RPM_SYS_FABRIC_CLK] =		{ 28, 12, 9, 1 },
++	[QCOM_RPM_NSS_FABRIC_0_CLK] =		{ 29, 13, 10, 1 },
++	[QCOM_RPM_DAYTONA_FABRIC_CLK] =		{ 30, 14, 11, 1 },
++	[QCOM_RPM_SFPB_CLK] =			{ 31, 15, 12, 1 },
++	[QCOM_RPM_CFPB_CLK] =			{ 32, 16, 13, 1 },
++	[QCOM_RPM_NSS_FABRIC_1_CLK] =		{ 33, 17, 14, 1 },
++	[QCOM_RPM_EBI1_CLK] =			{ 34, 18, 16, 1 },
++	[QCOM_RPM_APPS_FABRIC_HALT] =		{ 35, 19, 18, 2 },
++	[QCOM_RPM_APPS_FABRIC_MODE] =		{ 37, 20, 19, 3 },
++	[QCOM_RPM_APPS_FABRIC_IOCTL] =		{ 40, 21, 20, 1 },
++	[QCOM_RPM_APPS_FABRIC_ARB] =		{ 41, 22, 21, 12 },
++	[QCOM_RPM_SYS_FABRIC_HALT] =		{ 53, 23, 22, 2 },
++	[QCOM_RPM_SYS_FABRIC_MODE] =		{ 55, 24, 23, 3 },
++	[QCOM_RPM_SYS_FABRIC_IOCTL] =		{ 58, 25, 24, 1 },
++	[QCOM_RPM_SYS_FABRIC_ARB] =		{ 59, 26, 25, 30 },
++	[QCOM_RPM_MM_FABRIC_HALT] =		{ 89, 27, 26, 2 },
++	[QCOM_RPM_MM_FABRIC_MODE] =		{ 91, 28, 27, 3 },
++	[QCOM_RPM_MM_FABRIC_IOCTL] =		{ 94, 29, 28, 1 },
++	[QCOM_RPM_MM_FABRIC_ARB] =		{ 95, 30, 29, 2 },
++	[QCOM_RPM_CXO_BUFFERS] =		{ 209, 33, 31, 1 },
++	[QCOM_RPM_USB_OTG_SWITCH] =		{ 210, 34, 32, 1 },
++	[QCOM_RPM_HDMI_SWITCH] =		{ 211, 35, 33, 1 },
++	[QCOM_RPM_DDR_DMM] =			{ 212, 36, 34, 2 },
++	[QCOM_RPM_VDDMIN_GPIO] =		{ 215, 40, 39, 1 },
++	[QCOM_RPM_SMB208_S1a] =			{ 216, 41, 90, 2 },
++	[QCOM_RPM_SMB208_S1b] =			{ 218, 43, 91, 2 },
++	[QCOM_RPM_SMB208_S2a] =			{ 220, 45, 92, 2 },
++	[QCOM_RPM_SMB208_S2b] =			{ 222, 47, 93, 2 },
++};
++
++static const struct qcom_rpm_data ipq806x_template = {
++	.version = 3,
++	.resource_table = ipq806x_rpm_resource_table,
++	.n_resources = ARRAY_SIZE(ipq806x_rpm_resource_table),
++};
++
+ static const struct of_device_id qcom_rpm_of_match[] = {
+ 	{ .compatible = "qcom,rpm-apq8064", .data = &apq8064_template },
+ 	{ .compatible = "qcom,rpm-msm8660", .data = &msm8660_template },
+ 	{ .compatible = "qcom,rpm-msm8960", .data = &msm8960_template },
++	{ .compatible = "qcom,rpm-ipq8064", .data = &ipq806x_template },
+ 	{ }
+ };
+ MODULE_DEVICE_TABLE(of, qcom_rpm_of_match);
diff --git a/target/linux/ipq806x/patches-4.0/123-mfd-devicetree-qcom_rpm-Document-IPQ8064-resources.patch b/target/linux/ipq806x/patches-4.0/123-mfd-devicetree-qcom_rpm-Document-IPQ8064-resources.patch
new file mode 100644
index 0000000000..c8a9f3f5d0
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/123-mfd-devicetree-qcom_rpm-Document-IPQ8064-resources.patch
@@ -0,0 +1,42 @@
+From 30bc3aa5c4ed3072bdff7d915772df1b91307ed4 Mon Sep 17 00:00:00 2001
+From: Josh Cartwright <joshc@codeaurora.org>
+Date: Thu, 26 Mar 2015 11:29:25 -0700
+Subject: [PATCH] mfd: devicetree: qcom_rpm: Document IPQ8064 resources
+
+The IPQ8064 SoC has several RPM-controlled resources, an NSS fabrick
+clock and four regulator resources.  Provide definitions for them.
+
+Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
+[sboyd@codeaurora.org: Drop regulator part of binding]
+Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
+Signed-off-by: Lee Jones <lee.jones@linaro.org>
+---
+ Documentation/devicetree/bindings/mfd/qcom-rpm.txt | 1 +
+ include/dt-bindings/mfd/qcom-rpm.h                 | 6 ++++++
+ 2 files changed, 7 insertions(+)
+
+--- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
++++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
+@@ -12,6 +12,7 @@ frequencies.
+ 		    "qcom,rpm-apq8064"
+ 		    "qcom,rpm-msm8660"
+ 		    "qcom,rpm-msm8960"
++		    "qcom,rpm-ipq8064"
+ 
+ - reg:
+ 	Usage: required
+--- a/include/dt-bindings/mfd/qcom-rpm.h
++++ b/include/dt-bindings/mfd/qcom-rpm.h
+@@ -141,6 +141,12 @@
+ #define QCOM_RPM_SYS_FABRIC_MODE		131
+ #define QCOM_RPM_USB_OTG_SWITCH			132
+ #define QCOM_RPM_VDDMIN_GPIO			133
++#define QCOM_RPM_NSS_FABRIC_0_CLK		134
++#define QCOM_RPM_NSS_FABRIC_1_CLK		135
++#define QCOM_RPM_SMB208_S1a			136
++#define QCOM_RPM_SMB208_S1b			137
++#define QCOM_RPM_SMB208_S2a			138
++#define QCOM_RPM_SMB208_S2b			139
+ 
+ /*
+  * Constants used to select force mode for regulators.
diff --git a/target/linux/ipq806x/patches-4.0/126-add-rpm-to-ipq8064-dts.patch b/target/linux/ipq806x/patches-4.0/126-add-rpm-to-ipq8064-dts.patch
new file mode 100644
index 0000000000..854131c7f6
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.0/126-add-rpm-to-ipq8064-dts.patch
@@ -0,0 +1,87 @@
+--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
+@@ -2,6 +2,7 @@
+ 
+ #include "skeleton.dtsi"
+ #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
++#include <dt-bindings/mfd/qcom-rpm.h>
+ #include <dt-bindings/soc/qcom,gsbi.h>
+ #include <dt-bindings/reset/qcom,gcc-ipq806x.h>
+ 
+@@ -75,6 +76,63 @@
+ 		ranges;
+ 		compatible = "simple-bus";
+ 
++		rpm@108000 {
++			compatible = "qcom,rpm-ipq8064";
++			reg = <0x108000 0x1000>;
++			qcom,ipc = <&l2cc 0x8 2>;
++
++			interrupts = <0 19 0>,
++				     <0 21 0>,
++				     <0 22 0>;
++			interrupt-names = "ack",
++					  "err",
++					  "wakeup";
++
++			#address-cells = <1>;
++			#size-cells = <0>;
++
++			smb208_s1a: smb208-s1a {
++				compatible = "qcom,rpm-smb208";
++				reg = <QCOM_RPM_SMB208_S1a>;
++
++				regulator-min-microvolt = <1050000>;
++				regulator-max-microvolt = <1150000>;
++
++				qcom,switch-mode-frequency = <1200000>;
++
++			};
++
++			smb208_s1b: smb208-s1b {
++				compatible = "qcom,rpm-smb208";
++				reg = <QCOM_RPM_SMB208_S1b>;
++
++				regulator-min-microvolt = <1050000>;
++				regulator-max-microvolt = <1150000>;
++
++				qcom,switch-mode-frequency = <1200000>;
++			};
++
++			smb208_s2a: smb208-s2a {
++				compatible = "qcom,rpm-smb208";
++				reg = <QCOM_RPM_SMB208_S2a>;
++
++				regulator-min-microvolt = < 800000>;
++				regulator-max-microvolt = <1250000>;
++
++				qcom,switch-mode-frequency = <1200000>;
++			};
++
++			smb208_s2b: smb208-s2b {
++				compatible = "qcom,rpm-smb208";
++				reg = <QCOM_RPM_SMB208_S2b>;
++
++				regulator-min-microvolt = < 800000>;
++				regulator-max-microvolt = <1250000>;
++
++				qcom,switch-mode-frequency = <1200000>;
++			};
++		};
++
+ 		qcom_pinmux: pinmux@800000 {
+ 			compatible = "qcom,ipq8064-pinctrl";
+ 			reg = <0x800000 0x4000>;
+@@ -119,6 +177,12 @@
+ 			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+ 		};
+ 
++		l2cc: clock-controller@2011000 {
++			compatible = "qcom,kpss-gcc", "syscon";
++			reg = <0x2011000 0x1000>;
++			clock-output-names = "acpu_l2_aux";
++ 		};
++ 
+ 		saw0: regulator@2089000 {
+ 			compatible = "qcom,saw2";
+ 			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
diff --git a/target/linux/ipq806x/patches-4.0/700-add-gmac-dts-suport.patch b/target/linux/ipq806x/patches-4.0/700-add-gmac-dts-suport.patch
index b5643dfd17..25a9373208 100644
--- a/target/linux/ipq806x/patches-4.0/700-add-gmac-dts-suport.patch
+++ b/target/linux/ipq806x/patches-4.0/700-add-gmac-dts-suport.patch
@@ -119,15 +119,15 @@
  };
 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
 +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -4,6 +4,7 @@
- #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
+@@ -5,6 +5,7 @@
+ #include <dt-bindings/mfd/qcom-rpm.h>
  #include <dt-bindings/soc/qcom,gsbi.h>
  #include <dt-bindings/reset/qcom,gcc-ipq806x.h>
 +#include <dt-bindings/interrupt-controller/arm-gic.h>
  
  / {
  	model = "Qualcomm IPQ8064";
-@@ -415,5 +416,42 @@
+@@ -479,5 +480,42 @@
  
  			status = "disabled";
  		};