aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
authorSteven Lin <steven.lin@senao.com>2019-09-02 10:39:45 +0800
committerChristian Lamparter <chunkeey@gmail.com>2020-02-28 22:29:10 +0100
commita736d912e2bad6c470c73fbf47c45ec3017371af (patch)
tree6b4da25fb2d2f0d2c9fff5419b105f1d1402e641 /target/linux
parent977c7f12deefc152b7d62de06f4973a54a71d746 (diff)
downloadupstream-a736d912e2bad6c470c73fbf47c45ec3017371af.tar.gz
upstream-a736d912e2bad6c470c73fbf47c45ec3017371af.tar.bz2
upstream-a736d912e2bad6c470c73fbf47c45ec3017371af.zip
ipq40xx: add support for EnGenius EAP2200
SOC: IPQ4019 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB FLASH: NOR 4 MiB + NAND 128 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2 WLAN2: Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2 INPUT: WPS Button LEDS: Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. c. Set a static ip 192.168.99.8 for Ethernet that connects to board. d. The PC must have a TFTP server launched and listening on the interface to which the board is connected. e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm Signed-off-by: Steven Lin <steven.lin@senao.com> [copied 4.19 dts to 5.4] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Diffstat (limited to 'target/linux')
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/01_leds4
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/02_network4
-rw-r--r--target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata9
-rw-r--r--target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh4
-rw-r--r--target/linux/ipq40xx/base-files/lib/upgrade/platform.sh1
-rw-r--r--target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts282
-rw-r--r--target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts282
-rw-r--r--target/linux/ipq40xx/image/Makefile12
-rw-r--r--target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch3
-rw-r--r--target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch5
10 files changed, 599 insertions, 7 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index 0326bab382..dd7f35a0a3 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -33,6 +33,10 @@ engenius,eap1300)
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:yellow:wlan5g" "phy1tpt"
ucidef_set_led_default "mesh" "MESH" "${boardname}:blue:mesh" "0"
;;
+engenius,eap2200)
+ ucidef_set_led_netdev "lan1" "LAN1" "${boardname}:blue:lan1" "eth0"
+ ucidef_set_led_netdev "lan2" "LAN2" "${boardname}:blue:lan2" "eth1"
+ ;;
engenius,ens620ext)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2G" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5G" "phy1tpt"
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 4b636fc701..190286541a 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -58,7 +58,8 @@ ipq40xx_setup_interfaces()
;;
avm,fritzrepeater-3000|\
compex,wpj419|\
- compex,wpj428)
+ compex,wpj428|\
+ engenius,eap2200)
ucidef_set_interface_lan "eth0 eth1"
;;
ezviz,cs-w3-wd1200g-eup)
@@ -109,6 +110,7 @@ ipq40xx_setup_macs()
lan_mac=$(mtd_get_mac_ascii bdcfg lanmac)
label_mac=$lan_mac
;;
+ engenius,eap220|\
engenius,emd1)
lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
label_mac=$lan_mac
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 957bee12ab..50bfbb0a86 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -31,14 +31,15 @@ case "$FIRMWARE" in
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
+ engenius,eap2200 |\
+ openmesh,a62)
+ caldata_extract "0:ART" 0x9000 0x2f20
+ ;;
linksys,ea8300)
caldata_extract "ART" 0x9000 0x2f20
# OEM assigns 4 sequential MACs
ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4))
;;
- openmesh,a62)
- caldata_extract "0:ART" 0x9000 0x2f20
- ;;
esac
;;
"ath10k/pre-cal-ahb-a000000.wifi.bin")
@@ -80,6 +81,7 @@ case "$FIRMWARE" in
compex,wpj419 |\
compex,wpj428 |\
engenius,eap1300 |\
+ engenius,eap2200 |\
openmesh,a42 |\
openmesh,a62 |\
qxwlan,e2600ac-c1 |\
@@ -159,6 +161,7 @@ case "$FIRMWARE" in
compex,wpj419 |\
compex,wpj428 |\
engenius,eap1300 |\
+ engenius,eap2200 |\
openmesh,a42 |\
openmesh,a62 |\
qxwlan,e2600ac-c1 |\
diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
index 1bca152a38..f9ec8ab055 100644
--- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
+++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
@@ -13,6 +13,10 @@ preinit_set_mac_address() {
ip link set dev eth0 address $(mtd_get_mac_binary "ART" 0x6)
ip link set dev eth1 address $(mtd_get_mac_binary "ART" 0x0)
;;
+ engenius,eap2200)
+ base_mac=$(cat /sys/class/net/eth0/address)
+ ip link set dev eth1 address $(macaddr_add "${base_mac}" +1)
+ ;;
linksys,ea8300)
base_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ip link set dev eth0 address "${base_mac}"
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index cdf7a2b8f2..377f65ea42 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -53,6 +53,7 @@ platform_do_upgrade() {
avm,fritzrepeater-1200 |\
avm,fritzrepeater-3000 |\
cilab,meshpoint-one |\
+ engenius,eap2200 |\
qxwlan,e2600ac-c2)
nand_do_upgrade "$1"
;;
diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts
new file mode 100644
index 0000000000..6862ca87e3
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "EnGenius EAP2200";
+ compatible = "engenius,eap2200";
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "eap2200:amber:power";
+ gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+ };
+
+ lan1 {
+ label = "eap2200:blue:lan1";
+ gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+ };
+
+ lan2 {
+ label = "eap2200:blue:lan2";
+ gpios = <&tlmm 45 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan2g {
+ label = "eap2200:blue:wlan2g";
+ gpios = <&tlmm 46 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wlan5g {
+ label = "eap2200:yellow:wlan5g";
+ gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ wlan5g2 {
+ label = "eap2200:yellow:wlan5g2";
+ gpios = <&tlmm 48 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy2tpt";
+ };
+
+ mode {
+ label = "eap2200:blue:mode";
+ gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ switch_lan_bmp = <0x10>;
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0@0 {
+ label = "0:SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition1@40000 {
+ label = "0:MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition2@60000 {
+ label = "0:QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition3@c0000 {
+ label = "0:CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition4@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition5@e0000 {
+ label = "0:APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+ partition6@f0000 {
+ label = "0:APPSBL";
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+ partition7@170000 {
+ label = "0:ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ vlan_tag = <1 0x10>;
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "rootfs1";
+ reg = <0x00000000 0x04000000>;
+ };
+ partition@40000000 {
+ label = "ubi";
+ reg = <0x04000000 0x04000000>;
+ };
+
+ };
+ };
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi2: wifi@1,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x00010000 0 0 0 0>;
+ ieee80211-freq-limit = <5470000 5875000>;
+ qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+ };
+ };
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+};
+
+&wifi1 {
+ status = "okay";
+ ieee80211-freq-limit = <5170000 5350000>;
+ qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+};
diff --git a/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts
new file mode 100644
index 0000000000..6862ca87e3
--- /dev/null
+++ b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "EnGenius EAP2200";
+ compatible = "engenius,eap2200";
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "eap2200:amber:power";
+ gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+ };
+
+ lan1 {
+ label = "eap2200:blue:lan1";
+ gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+ };
+
+ lan2 {
+ label = "eap2200:blue:lan2";
+ gpios = <&tlmm 45 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan2g {
+ label = "eap2200:blue:wlan2g";
+ gpios = <&tlmm 46 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wlan5g {
+ label = "eap2200:yellow:wlan5g";
+ gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ wlan5g2 {
+ label = "eap2200:yellow:wlan5g2";
+ gpios = <&tlmm 48 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy2tpt";
+ };
+
+ mode {
+ label = "eap2200:blue:mode";
+ gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ switch_lan_bmp = <0x10>;
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0@0 {
+ label = "0:SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition1@40000 {
+ label = "0:MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition2@60000 {
+ label = "0:QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition3@c0000 {
+ label = "0:CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition4@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition5@e0000 {
+ label = "0:APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+ partition6@f0000 {
+ label = "0:APPSBL";
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+ partition7@170000 {
+ label = "0:ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ vlan_tag = <1 0x10>;
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "rootfs1";
+ reg = <0x00000000 0x04000000>;
+ };
+ partition@40000000 {
+ label = "ubi";
+ reg = <0x04000000 0x04000000>;
+ };
+
+ };
+ };
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi2: wifi@1,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x00010000 0 0 0 0>;
+ ieee80211-freq-limit = <5470000 5875000>;
+ qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+ };
+ };
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+};
+
+&wifi1 {
+ status = "okay";
+ ieee80211-freq-limit = <5170000 5350000>;
+ qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index bbe4df9df4..9ddcd17f1d 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -278,6 +278,18 @@ define Device/engenius_eap1300
endef
TARGET_DEVICES += engenius_eap1300
+define Device/engenius_eap2200
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := EnGenius
+ DEVICE_MODEL := EAP2200
+ SOC := qcom-ipq4019
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-engenius_eap2200 -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
+endef
+TARGET_DEVICES += engenius_eap2200
+
define Device/engenius_emd1
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
index 11e775a5dc..89e665db23 100644
--- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,42 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,43 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -36,6 +36,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
qcom-ipq4019-ap.dk07.1-c1.dtb \
qcom-ipq4019-ap.dk07.1-c2.dtb \
+ qcom-ipq4019-a62.dtb \
++ qcom-ipq4019-eap2200.dtb \
+ qcom-ipq4019-fritzbox-7530.dtb \
+ qcom-ipq4019-fritzrepeater-1200.dtb \
+ qcom-ipq4019-fritzrepeater-3000.dtb \
diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
index 11e775a5dc..da53220f09 100644
--- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,42 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,43 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -36,10 +36,11 @@ Signed-off-by: John Crispin <john@phrozen.org>
qcom-ipq4019-ap.dk07.1-c1.dtb \
qcom-ipq4019-ap.dk07.1-c2.dtb \
+ qcom-ipq4019-a62.dtb \
++ qcom-ipq4019-ea8300.dtb \
++ qcom-ipq4019-eap2200.dtb \
+ qcom-ipq4019-fritzbox-7530.dtb \
+ qcom-ipq4019-fritzrepeater-1200.dtb \
+ qcom-ipq4019-fritzrepeater-3000.dtb \
-+ qcom-ipq4019-ea8300.dtb \
+ qcom-ipq4019-map-ac2200.dtb \
+ qcom-ipq4019-e2600ac-c1.dtb \
+ qcom-ipq4019-e2600ac-c2.dtb \