aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/realtek
diff options
context:
space:
mode:
authorBirger Koblitz <git@birger-koblitz.de>2022-04-24 22:01:31 +0200
committerSander Vanheule <sander@svanheule.net>2022-05-11 22:23:50 +0200
commitd1b824650f1ee694ec2dbdd2f4f9ec64e650cf86 (patch)
treeaf9bbb14eecb79c7b15fa2a3d814e177a89f04f1 /target/linux/realtek
parentd9a063c3967c72773616cf5eadd4f978b9724c50 (diff)
downloadupstream-d1b824650f1ee694ec2dbdd2f4f9ec64e650cf86.tar.gz
upstream-d1b824650f1ee694ec2dbdd2f4f9ec64e650cf86.tar.bz2
upstream-d1b824650f1ee694ec2dbdd2f4f9ec64e650cf86.zip
realtek: do not reset SerDes on link change
Do not reset the RTL930x SerDes on link changes, instead set up the SDS with internal PHYs for the SFP+ ports only. This fixes the 8 1GBit ports on the Zyxel XGS1250 which do not work without this patch. A complete SerDes reset was performed on all SerDes links. For copper 1Gbit ports, this is commonly a single XGMII link to an RTL8218D. There is however no support for setting up the XGMII link on RTL9300/RTL9310, thereby wiping the (RX/TX) setup done by u-boot and breaking the 1GBit ports. No SerDes reset should be done for these links. The handling of SGMII/HiSGMII, 1000BX or 10GR links is actually entirely different. All these modes need to be suitably RX calibrated and the pre- main and post- amplifiers set up properly for TX. The 10GBit SFP+ fiber links are recalibrated instead of reset, which e.g. is necessary when someone pulls a module out and puts another in. This makes swapping out 10GBit fiber modules possible. 1GBit modules are not yet supported, nor any modules with an internal phy. Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Birger Koblitz <git@birger-koblitz.de> [rewrite commit message based on discussion] Link: http://lists.infradead.org/pipermail/openwrt-devel/2022-May/038623.html Signed-off-by: Sander Vanheule <sander@svanheule.net>
Diffstat (limited to 'target/linux/realtek')
-rw-r--r--target/linux/realtek/files-5.10/drivers/net/dsa/rtl83xx/dsa.c3
-rw-r--r--target/linux/realtek/files-5.10/drivers/net/dsa/rtl83xx/rtl83xx.h1
2 files changed, 3 insertions, 1 deletions
diff --git a/target/linux/realtek/files-5.10/drivers/net/dsa/rtl83xx/dsa.c b/target/linux/realtek/files-5.10/drivers/net/dsa/rtl83xx/dsa.c
index 2e3ab4a805..f54fdd298a 100644
--- a/target/linux/realtek/files-5.10/drivers/net/dsa/rtl83xx/dsa.c
+++ b/target/linux/realtek/files-5.10/drivers/net/dsa/rtl83xx/dsa.c
@@ -817,7 +817,8 @@ static void rtl93xx_phylink_mac_config(struct dsa_switch *ds, int port,
__func__, phy_modes(state->interface));
return;
}
- rtl9300_sds_rst(sds_num, sds_mode);
+ if (state->interface == PHY_INTERFACE_MODE_10GBASER)
+ rtl9300_serdes_setup(sds_num, state->interface);
}
reg = sw_r32(priv->r->mac_force_mode_ctrl(port));
diff --git a/target/linux/realtek/files-5.10/drivers/net/dsa/rtl83xx/rtl83xx.h b/target/linux/realtek/files-5.10/drivers/net/dsa/rtl83xx/rtl83xx.h
index 0bb11f9b8b..107016469c 100644
--- a/target/linux/realtek/files-5.10/drivers/net/dsa/rtl83xx/rtl83xx.h
+++ b/target/linux/realtek/files-5.10/drivers/net/dsa/rtl83xx/rtl83xx.h
@@ -121,6 +121,7 @@ irqreturn_t rtl839x_switch_irq(int irq, void *dev_id);
void rtl930x_vlan_profile_dump(int index);
int rtl9300_sds_power(int mac, int val);
void rtl9300_sds_rst(int sds_num, u32 mode);
+int rtl9300_serdes_setup(int sds_num, phy_interface_t phy_mode);
void rtl930x_print_matrix(void);
/* RTL931x-specific */