diff options
| author | Julien Dusser <julien.dusser@free.fr> | 2022-03-20 10:11:15 +0100 |
|---|---|---|
| committer | Hauke Mehrtens <hauke@hauke-m.de> | 2022-12-18 21:24:57 +0100 |
| commit | b893aa7992087c105ea205088f8d9787200ed6f8 (patch) | |
| tree | 26c20a92b4aa6e75967cb1cb06f1c25c8613f5a8 /target/linux/ramips/mt76x8 | |
| parent | 8be6350f6646b37929f40a9a482343f22af2065b (diff) | |
| download | upstream-b893aa7992087c105ea205088f8d9787200ed6f8.tar.gz upstream-b893aa7992087c105ea205088f8d9787200ed6f8.tar.bz2 upstream-b893aa7992087c105ea205088f8d9787200ed6f8.zip | |
ramips: add support for Linksys E5400 and clones
Linksys E5400 is a 2.4/5GHz dual band AC router, based on MediaTek
MT7628AN. This device is also sold as Linksys E2500v4, E5300 and E5350
with the same hardware, but software speed limitations in vendor
firmwares.
Specification:
* SoC: MT7628AN (580 MHz)
* RAM: DDR2 64 MiB
* Flash: 16 MiB NOR (W25Q128BV)
* Wi-Fi:
* 2.4GHz: SoC Built-in
* 5GHz: MT7612EN
* Ethernet: 5x 100Mbps
* Switch: SoC built-in
* UART:
* 115200, 8N1, 3.3V (real u-boot speed: 119050)
* Pinout JB4: 1:[3V3] (TXD) (RXD) [NC] (GND)
Flash Layout:
0x0000000-0x0030000 : "Bootloader"
0x0030000-0x0040000 : "Config"
0x0040000-0x0050000 : "Factory"
0x0050000-0x0ff0000 : "Kernel"
0x0ff0000-0x1000000 : "CBTinfo"
MAC address:
LAN: factory 0x28
WAN: LAN + 1
2.4G: LAN + 2
5G: LAN + 3
Installation:
1. Connect to UART, use LF as EOL (not CRLF)
2. Set IP address
- Press 4 during boot
- setenv serverip <TFTPSERVER_IP>
- setenv ipaddr <DEVICE_IP>
- setenv bootfile openwrt-ramips-mt76x8-linksys_e5400-initramfs-kernel.bin
- saveenv
- reset
3. Load Openwrt Kernel image from TFTP:
- Press 1 during boot
- IP and filename should be already set
4. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
Diffstat (limited to 'target/linux/ramips/mt76x8')
| -rw-r--r-- | target/linux/ramips/mt76x8/base-files/etc/board.d/02_network | 7 |
1 files changed, 7 insertions, 0 deletions
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network index d85cdf3db7..26415e0fa6 100644 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network @@ -125,6 +125,10 @@ ramips_setup_interfaces() ucidef_set_interface_lan "eth0" ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi" ;; + linksys,e5400) + ucidef_add_switch "switch0" \ + "0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "4:wan" "6@eth0" + ;; motorola,mwr03) ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "0:wan" "6@eth0" @@ -248,6 +252,9 @@ ramips_setup_macs() totolink,lr1200) wan_mac=$(mtd_get_mac_binary factory 0x2e) ;; + linksys,e5400) + wan_mac=$(mtd_get_mac_binary factory 0x22) + ;; mercury,mac1200r-v2) wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory_info 0xd)" 1) ;; |