diff options
| author | Rodolphe de Saint Léger <rdesaintleger@gmail.com> | 2022-03-16 10:19:30 +0100 |
|---|---|---|
| committer | Sungbo Eo <mans0n@gorani.run> | 2022-03-16 22:36:04 +0900 |
| commit | 7bc20cb6143e089fae6ad4b173fc42b55bdbecfe (patch) | |
| tree | b480155ec15e9c06df6e0b6ac7f471c3a62ea862 /target/linux/ramips/mt7620/base-files/etc | |
| parent | be89c9eec4c28123b61ed020ad5b8b02905e73af (diff) | |
| download | upstream-7bc20cb6143e089fae6ad4b173fc42b55bdbecfe.tar.gz upstream-7bc20cb6143e089fae6ad4b173fc42b55bdbecfe.tar.bz2 upstream-7bc20cb6143e089fae6ad4b173fc42b55bdbecfe.zip | |
ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Diffstat (limited to 'target/linux/ramips/mt7620/base-files/etc')
| -rw-r--r-- | target/linux/ramips/mt7620/base-files/etc/board.d/01_leds | 3 | ||||
| -rw-r--r-- | target/linux/ramips/mt7620/base-files/etc/board.d/02_network | 1 |
2 files changed, 3 insertions, 1 deletions
diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds index 5f105bd834..1293c34cbf 100644 --- a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds @@ -161,7 +161,8 @@ lenovo,newifi-y1s) ucidef_set_led_netdev "wan" "WAN" "blue:internet" "eth0.2" "tx rx" ;; netgear,ex2700|\ -netgear,wn3000rp-v3) +netgear,wn3000rp-v3|\ +netgear,wn3100rp-v2) ucidef_set_led_netdev "wifi_led" "wifi" "green:router" "wlan0" ;; netgear,ex3700|\ diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network index 3ed72fa3ab..f7bc41669f 100644 --- a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network @@ -54,6 +54,7 @@ ramips_setup_interfaces() netgear,ex6120|\ netgear,ex6130|\ netgear,wn3000rp-v3|\ + netgear,wn3100rp-v2|\ planex,cs-qr10|\ planex,mzk-ex300np|\ planex,mzk-ex750np|\ |