aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7620/base-files/etc
diff options
context:
space:
mode:
authorRodolphe de Saint Léger <rdesaintleger@gmail.com>2022-03-16 10:19:30 +0100
committerSungbo Eo <mans0n@gorani.run>2022-03-16 23:14:25 +0900
commit46c5de53856d97a1a926a272acc76a9af654f320 (patch)
treeb480155ec15e9c06df6e0b6ac7f471c3a62ea862 /target/linux/ramips/mt7620/base-files/etc
parentfe34001ee5a6bdb6208ed935e0302d26deafe249 (diff)
downloadupstream-46c5de53856d97a1a926a272acc76a9af654f320.tar.gz
upstream-46c5de53856d97a1a926a272acc76a9af654f320.tar.bz2
upstream-46c5de53856d97a1a926a272acc76a9af654f320.zip
ramips: add support for Netgear WN3100RPv2
This patch adds support for the Netgear WN3100RPv2 http://www.netgear.com/support/product/wn3100rpv2.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This device seems to be same hardware as a WN3000RPv3 Flash instructions: - Use the Netgear WebUI to upgrade to OpenWRT using the factory image (see note below), - Use the sysupgrade image for upgrading versions from OpenWRT, - TFTP recovery procedure can be used to flash the factory image (preferred method). Note: - The WebUI may not reboot automatically, wait at least 5 minutes before powercycling the device Flashing using TFTP: - Set you IP address to 192.168.1.10/24 (no gateway) - Connect your machine to the Ethernet port - Power off the device and wait for 10 seconds, - Hold the reset button and power on the device (do not release reset), - Hold the reset button until the green light is flashing (Approx. 15s) - launch tftp, set mode to binary and connect to 192.168.1.1 - put the factory firmware image - All leds will switch off (like a power off), this is normal - Wait for the device to reboot in the new OpenWRT image (max 5 mins) - The first boot will take longer than usual. - After boot, the Device IP on the ethernet port is 192.168.1.1 Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com> [drop unneeded includes in dts, wrap commit message] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Diffstat (limited to 'target/linux/ramips/mt7620/base-files/etc')
-rw-r--r--target/linux/ramips/mt7620/base-files/etc/board.d/01_leds3
-rw-r--r--target/linux/ramips/mt7620/base-files/etc/board.d/02_network1
2 files changed, 3 insertions, 1 deletions
diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
index 5f105bd834..1293c34cbf 100644
--- a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
@@ -161,7 +161,8 @@ lenovo,newifi-y1s)
ucidef_set_led_netdev "wan" "WAN" "blue:internet" "eth0.2" "tx rx"
;;
netgear,ex2700|\
-netgear,wn3000rp-v3)
+netgear,wn3000rp-v3|\
+netgear,wn3100rp-v2)
ucidef_set_led_netdev "wifi_led" "wifi" "green:router" "wlan0"
;;
netgear,ex3700|\
diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
index 3ed72fa3ab..f7bc41669f 100644
--- a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
@@ -54,6 +54,7 @@ ramips_setup_interfaces()
netgear,ex6120|\
netgear,ex6130|\
netgear,wn3000rp-v3|\
+ netgear,wn3100rp-v2|\
planex,cs-qr10|\
planex,mzk-ex300np|\
planex,mzk-ex750np|\