ramips: add support for I-O DATA WN-DX1167R

I-O DATA WN-DX1167R is a 2.4/5 GHz band 11ac rotuer, based on MediaTek
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: NAND 128 MiB
- WLAN		: MediaTek MT7615D (2.4/5 GHz, 2T2R)
- Ethernet	: 5x 10/100/1000 Mbps
  - Switch	: MediaTek MT7621A (MT7530)
- LEDs/Input	: 2x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J5: Vcc, TX, RX, NC, GND
  - 57600 bps

Flash instruction using initramfs image:

1. Boot WN-DX1167R normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新")
button to perform firmware update
4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade
image
5. Wait ~120 seconds to complete flashing

Notes:

- configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode
for MT7615D chip is not supported in mt76 driver
- last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" by MSTC
(MitraStar Technology Corp.), but U-Boot doesn't
  - uImage magic (0x0 - 0x3) : 0x434F4D43 (COMC)
  - header crc32 (0x4 - 0x7) : with data length and data crc32
  - image name (0x20 - 0x37) : model ID and firmware versions
  - data length (0x38 - 0x3b): kernel + rootfs
  - data crc32 (0x3c - 0x3f) : kernel + rootfs

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>

1 files changed, 140 insertions, 0 deletions

diff --git a/target/linux/ramips/dts/mt7621_iodata_wn-xx-xr.dtsi b/target/linux/ramips/dts/mt7621_iodata_wn-xx-xr.dtsi
new file mode 100644
index 0000000000..8b3329113f
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_iodata_wn-xx-xr.dtsi
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wps {
+			label = "iodata:green:wps";
+			gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
+		};
+
+		led_power: power {
+			label = "iodata:green:power";
+			gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		repeater {
+			label = "repeater";
+			gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partitions: partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x0100000>;
+			read-only;
+		};
+
+		partition@100000 {
+			label = "u-boot-env";
+			reg = <0x0100000 0x0100000>;
+			read-only;
+		};
+
+		factory: partition@200000 {
+			label = "factory";
+			reg = <0x0200000 0x0100000>;
+		};
+
+		partition@300000 {
+			label = "SecondBoot";
+			reg = <0x0300000 0x0100000>;
+			read-only;
+		};
+
+		partition@400000 {
+			label = "kernel";
+			reg = <0x0400000 0x0400000>;
+		};
+
+		partition@800000 {
+			label = "ubi";
+			reg = <0x0800000 0x2e00000>;
+		};
+
+		partition@3600000 {
+			label = "Config";
+			reg = <0x3600000 0x0100000>;
+			read-only;
+		};
+
+		partition@3700000 {
+			label = "firmware_2";
+			reg = <0x3700000 0x3200000>;
+		};
+
+		partition@6900000 {
+			label = "Config_2";
+			reg = <0x6900000 0x0100000>;
+			read-only;
+		};
+
+		partition@6a00000 {
+			label = "persist";
+			reg = <0x6a00000 0x0100000>;
+		};
+	};
+};
+
+&ethernet {
+	mtd-mac-address = <&factory 0xe000>;
+};
+
+&pcie {
+	status = "okay";
+};
+
+&state_default {
+	gpio {
+		ralink,group = "uart2", "uart3", "wdt";
+		ralink,function = "gpio";
+	};
+};
+
+&xhci {
+	status = "disabled";
+};