aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts/BDCOM-WAP2100-SK.dts
diff options
context:
space:
mode:
authorPetr Štetiar <ynezz@true.cz>2018-11-13 13:10:40 +0100
committerJohn Crispin <john@phrozen.org>2018-11-26 12:05:44 +0100
commit16b950c981c91bcd2dde8bd1c4ed10bf3a6b1763 (patch)
treeffff163f2eb674dc8950e4b7fd1f70b2af59d8ee /target/linux/ramips/dts/BDCOM-WAP2100-SK.dts
parent022ffb56b2491fd7d8051ac6e6c7622ecc313d8f (diff)
downloadupstream-16b950c981c91bcd2dde8bd1c4ed10bf3a6b1763.tar.gz
upstream-16b950c981c91bcd2dde8bd1c4ed10bf3a6b1763.tar.bz2
upstream-16b950c981c91bcd2dde8bd1c4ed10bf3a6b1763.zip
ramips: Add support for ZTE ZXECS EBG3130 aka BDCOM WAP2100-SK
On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory OpenWrt image it's referenced as BDCOM WAP2100-SK device. Specifications: - SoC: MediaTek MT7620A - RAM: 128 MB - Flash: 16 MB - Ethernet: 5 FE ports - Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported) - UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config - LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G - Other: USB port, SD card slot and 2x external antennas (non-detachable) Flashing instructions: A) The U-Boot has HTTP based firmware upgrade A1) Flashing notes We've identified so far two different batches of units, unfortunately each batch has different U-Boot bootloader flashed with different default environment variables, thus each batch has different IP address for accessing web based firmware updater. * First batch has web based bootloader IP address 1.1.1.1 * Second batch has web based bootloader IP address 192.168.1.250 In case you can't connect to either of those IPs, you can try to get the default IP address via two methods: A1.1) Serial console, then the IP address is visible during the boot ... HTTP server is starting at IP: 1.1.1.1 raspi_read: from:40004 len:6 HTTP server is ready! ... A1.2) Over telnet/SSH using this command: root@bdcom:/# grep ipaddr= /dev/mtd0 ipaddr=1.1.1.1 A2) Flashing with browser * Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask * Reboot the device and try to reach web based bootloader in the browser with the following URL http://1.1.1.1 * Quickly select the firmware sysupgrade file and click on the `Update firmware` button, this all has to be done within 10 seconds, bootloader doesn't wait any longer If done correctly, the web page should show UPDATE IN PROGRESS page with progress indicator. Once the flashing completes (it takes roughly around 1 minute), the device will reboot to the OpenWrt firmware A3) Flashing with curl sudo ip addr add 1.1.1.2/24 dev eth0 curl \ --verbose \ --retry 3 \ --retry-delay 1 \ --retry-max-time 30 \ --connect-timeout 30 \ --form "firmware=@openwrt-ramips-mt7620-BDCOM-WAP2100-SK-squashfs-sysupgrade.bin" \ http://1.1.1.1 Now power on the router. B) The U-boot is based on Ralink SDK so we can flash the firmware using UART. 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX) 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. Signed-off-by: Petr Štetiar <ynezz@true.cz>
Diffstat (limited to 'target/linux/ramips/dts/BDCOM-WAP2100-SK.dts')
-rw-r--r--target/linux/ramips/dts/BDCOM-WAP2100-SK.dts130
1 files changed, 130 insertions, 0 deletions
diff --git a/target/linux/ramips/dts/BDCOM-WAP2100-SK.dts b/target/linux/ramips/dts/BDCOM-WAP2100-SK.dts
new file mode 100644
index 0000000000..7f9cbe74bd
--- /dev/null
+++ b/target/linux/ramips/dts/BDCOM-WAP2100-SK.dts
@@ -0,0 +1,130 @@
+/dts-v1/;
+
+#include "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "bdcom,bdcom-wap2100-sk", "ralink,mt7620a-soc";
+ model = "BDCOM WAP2100-SK";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ usb {
+ label = "wap2100-sk:green:usb";
+ gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "wap2100-sk:green:wps";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan2g {
+ label = "wap2100-sk:green:wlan2g";
+ gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ wps {
+ label = "wps";
+ gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ en25q128@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition@40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ firmware: partition@50000 {
+ label = "firmware";
+ reg = <0x50000 0xf70000>;
+ };
+ };
+};
+
+&gpio0 {
+ status = "okay";
+};
+
+&gpio1 {
+ status = "okay";
+};
+
+&gpio3 {
+ status = "okay";
+};
+
+&sdhci {
+ status = "okay";
+};
+
+&ehci {
+ status = "okay";
+};
+
+&ohci {
+ status = "okay";
+};
+
+&ethernet {
+ mtd-mac-address = <&factory 0x4>;
+ mediatek,portmap = "llllw";
+};
+
+&wmac {
+ ralink,mtd-eeprom = <&factory 0>;
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ default {
+ ralink,group = "wdt", "mdio", "spi refclk", "uartf", "wled";
+ ralink,function = "gpio";
+ };
+ };
+};