ramips: add support for the GnuBee Personal Cloud One

    The GnuBee Personal Cloud One crowdfunded on https://www.crowdsupply.com
    It is a low-cost, low-power, network-attached storage device.

    Specifications:

    - SoC: MediaTek MT7621AT
    - RAM: DDR3 512 MB
    - Flash: 32 MB
    - Six SATA ports for 2.5" Drives
    - One micro SDcard
    - One USB 3.0
    - Two USB 2.0
    - Gigabit Ethernet: 1 x WAN and 1 x LAN
    - UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
    - Four GPIOs available on a pin header

    Flash instructions:

    The GnuBee Personal Cloud One ships with libreCMC installed.
    libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
    As such one can upgrade using the webinterface or sysupgrade.

    Das U-Boot has multiple options for recovery or updates including :

    - USB
    - http
    - tftp

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use switchdev led trigger, all interfaces are in vlan1; rename leds
according to board.d setting; remove ge2 group from the pinmux, this
group doesn't exist in the driver]
Signed-off-by: Mathias Kresin <dev@kresin.me>

5 files changed, 13 insertions, 0 deletions

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 8ea464516c..8678a77796 100755..100644
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -183,6 +183,10 @@ fonera20n)
 	set_usb_led "$board:orange:usb"
 	set_wifi_led "$board:orange:wifi"
 	;;
+gb-pc1)
+	ucidef_set_led_switch "lan1" "lan1" "$board:green:lan1" "switch0" "0x01"
+	ucidef_set_led_switch "lan2" "lan2" "$board:green:lan2" "switch0" "0x10"
+	;;
 gl-mt300a|\
 gl-mt300n|\
 gl-mt750)
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 2d8a90cd3e..ee769b5a0f 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -186,6 +186,10 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0"
 		;;
+	gb-pc1)
+		ucidef_add_switch "switch0" \
+			"0:lan" "4:lan" "6@eth0"
+		;;
 	gl-mt300n-v2)
 		ucidef_add_switch "switch0" \
 			"1:lan" "0:wan" "6@eth0"
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 3933357aad..f5c0e835c0 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -77,6 +77,7 @@ get_status_led() {
 	dir-620-a1|\
 	dir-620-d1|\
 	dwr-512-b|\
+	gb-pc1|\
 	hpm|\
 	hw550-3g|\
 	mac1200rv2|\
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 0fd871a5d6..685ba070da 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -208,6 +208,9 @@ ramips_board_detect() {
 	*"FreeStation5")
 		name="freestation5"
 		;;
+	*"GB-PC1")
+		name="gb-pc1"
+		;;
 	*"GL-MT300A")
 		name="gl-mt300a"
 		;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 830e129115..b087d993b7 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -59,6 +59,7 @@ platform_check_image() {
 	firewrt|\
 	fonera20n|\
 	freestation5|\
+	gb-pc1|\
 	gl-mt300a|\
 	gl-mt300n|\
 	gl-mt750|\