aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/base-files/etc
diff options
context:
space:
mode:
authorPawel Dembicki <paweldembicki@gmail.com>2018-10-24 14:06:35 +0200
committerMathias Kresin <dev@kresin.me>2018-12-03 15:34:56 +0100
commite9a9b7d1ed76c88e097d5bc4dabf38735312558b (patch)
tree844dec550a138ed326345a8b3f1fdb8ade2ef6a6 /target/linux/ramips/base-files/etc
parent40692f0fb55ca5bd2426701b3a9e64e3b7487a7d (diff)
downloadupstream-e9a9b7d1ed76c88e097d5bc4dabf38735312558b.tar.gz
upstream-e9a9b7d1ed76c88e097d5bc4dabf38735312558b.tar.bz2
upstream-e9a9b7d1ed76c88e097d5bc4dabf38735312558b.zip
ramips: add support for D-Link DWR-118-A1
The DWR-118-A1 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 3x 10/100 Mbps Ethernet (3 LAN) - 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN) - 1x internal, non-detachable antenna - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - WIFI 5G LED not working - flash is very slow The status led has been assigned to the dwr-118-a1:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Diffstat (limited to 'target/linux/ramips/base-files/etc')
-rwxr-xr-xtarget/linux/ramips/base-files/etc/board.d/01_leds5
-rwxr-xr-xtarget/linux/ramips/base-files/etc/board.d/02_network5
-rw-r--r--target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom1
3 files changed, 11 insertions, 0 deletions
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index b2c69d4b59..f8c4b05b9a 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -114,6 +114,11 @@ dlink,dwr-116-a1|\
mzk-ex300np)
set_wifi_led "$boardname:green:wifi"
;;
+dlink,dwr-118-a1)
+ ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1f"
+ ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x20"
+ set_wifi_led "$boardname:green:wlan2g" "wlan1"
+ ;;
dlink,dwr-118-a2)
ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0e"
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01"
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 3af836a6f3..c207b7cad4 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -162,6 +162,10 @@ ramips_setup_interfaces()
wrh-300cr)
ucidef_set_interface_lan "eth0"
;;
+ dlink,dwr-118-a1)
+ ucidef_add_switch "switch0" \
+ "1:lan:2" "2:lan:3" "3:lan:1" "4:lan:0" "5:wan" "6@eth0"
+ ;;
dlink,dwr-118-a2)
ucidef_add_switch "switch0" \
"1:lan:2" "2:lan:1" "3:lan:3" "4:lan" "0:wan" "6@eth0"
@@ -475,6 +479,7 @@ ramips_setup_macs()
wan_mac=$(mtd_get_mac_ascii factory wanmac)
;;
dlink,dwr-116-a1|\
+ dlink,dwr-118-a1|\
dlink,dwr-118-a2|\
dlink,dwr-921-c1|\
lava,lr-25g001)
diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
index aee446d156..1d9de2d503 100644
--- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
+++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
@@ -55,6 +55,7 @@ case "$FIRMWARE" in
"soc_wmac.eeprom")
case $board in
dlink,dwr-116-a1|\
+ dlink,dwr-118-a1|\
dlink,dwr-118-a2|\
dlink,dwr-921-c1|\
lava,lr-25g001)