diff options
| author | Pawel Dembicki <paweldembicki@gmail.com> | 2018-10-24 14:06:35 +0200 |
|---|---|---|
| committer | Mathias Kresin <dev@kresin.me> | 2018-12-03 15:34:56 +0100 |
| commit | e9a9b7d1ed76c88e097d5bc4dabf38735312558b (patch) | |
| tree | 844dec550a138ed326345a8b3f1fdb8ade2ef6a6 /target/linux/ramips/base-files/etc | |
| parent | 40692f0fb55ca5bd2426701b3a9e64e3b7487a7d (diff) | |
| download | upstream-e9a9b7d1ed76c88e097d5bc4dabf38735312558b.tar.gz upstream-e9a9b7d1ed76c88e097d5bc4dabf38735312558b.tar.bz2 upstream-e9a9b7d1ed76c88e097d5bc4dabf38735312558b.zip | |
ramips: add support for D-Link DWR-118-A1
The DWR-118-A1 Wireless Router is based on the MT7620A SoC.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 3x 10/100 Mbps Ethernet (3 LAN)
- 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN)
- 1x internal, non-detachable antenna
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader
Known issues:
- WIFI 5G LED not working
- flash is very slow
The status led has been assigned to the dwr-118-a1:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.
Installation:
Apply factory image via http web-gui or JBOOT recovery page
How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Diffstat (limited to 'target/linux/ramips/base-files/etc')
3 files changed, 11 insertions, 0 deletions
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index b2c69d4b59..f8c4b05b9a 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -114,6 +114,11 @@ dlink,dwr-116-a1|\ mzk-ex300np) set_wifi_led "$boardname:green:wifi" ;; +dlink,dwr-118-a1) + ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1f" + ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x20" + set_wifi_led "$boardname:green:wlan2g" "wlan1" + ;; dlink,dwr-118-a2) ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0e" ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 3af836a6f3..c207b7cad4 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -162,6 +162,10 @@ ramips_setup_interfaces() wrh-300cr) ucidef_set_interface_lan "eth0" ;; + dlink,dwr-118-a1) + ucidef_add_switch "switch0" \ + "1:lan:2" "2:lan:3" "3:lan:1" "4:lan:0" "5:wan" "6@eth0" + ;; dlink,dwr-118-a2) ucidef_add_switch "switch0" \ "1:lan:2" "2:lan:1" "3:lan:3" "4:lan" "0:wan" "6@eth0" @@ -475,6 +479,7 @@ ramips_setup_macs() wan_mac=$(mtd_get_mac_ascii factory wanmac) ;; dlink,dwr-116-a1|\ + dlink,dwr-118-a1|\ dlink,dwr-118-a2|\ dlink,dwr-921-c1|\ lava,lr-25g001) diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom index aee446d156..1d9de2d503 100644 --- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom +++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom @@ -55,6 +55,7 @@ case "$FIRMWARE" in "soc_wmac.eeprom") case $board in dlink,dwr-116-a1|\ + dlink,dwr-118-a1|\ dlink,dwr-118-a2|\ dlink,dwr-921-c1|\ lava,lr-25g001) |