diff options
| author | INAGAKI Hiroshi <musashino.open@gmail.com> | 2019-01-09 00:20:18 +0900 |
|---|---|---|
| committer | Christian Lamparter <chunkeey@gmail.com> | 2019-02-14 16:56:14 +0100 |
| commit | f305ce5c3577005aba5b870b373e65aaf9ede3ec (patch) | |
| tree | 92801a53052461f74ca6e28bcf2d40c68fb1022a /target/linux/ramips/base-files/etc/board.d | |
| parent | dee8db441e480e7d581447f43219596f6dd9542a (diff) | |
| download | upstream-f305ce5c3577005aba5b870b373e65aaf9ede3ec.tar.gz upstream-f305ce5c3577005aba5b870b373e65aaf9ede3ec.tar.bz2 upstream-f305ce5c3577005aba5b870b373e65aaf9ede3ec.zip | |
ramips: add support for I-O DATA WN-AC1167GR
I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.
Specification:
- SoC : MediaTek MT7620A
- RAM : DDR2 64 MB
- Flash : SPI-NOR 8MB
- WLAN : 2.4/5 GHz, 2T2R
- 2.4 GHz: MT7620A (SoC)
- 5 GHz : MT7612E
- Ethernet: 10/100/1000 Mbps (ext. MT7530)
- LED/key : 4x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J2: TX, GND, RX, Vcc from SoC side
- 115200n8
Flash instruction using factory image:
1. Boot WN-AC1167GR normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Diffstat (limited to 'target/linux/ramips/base-files/etc/board.d')
| -rwxr-xr-x | target/linux/ramips/base-files/etc/board.d/01_leds | 4 | ||||
| -rwxr-xr-x | target/linux/ramips/base-files/etc/board.d/02_network | 7 |
2 files changed, 11 insertions, 0 deletions
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index e36f125126..4e2d534c99 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -188,6 +188,10 @@ ht-tm02) ucidef_set_led_netdev "eth" "Ethernet" "$boardname:green:lan" "eth0" set_wifi_led "$boardname:blue:wlan" ;; +iodata,wn-ac1167gr) + ucidef_set_led_wlan "wlan5g" "WLAN5G" "$boardname:green:wlan5g" "phy0radio" + ucidef_set_led_wlan "wlan2g" "WLAN2G" "$boardname:green:wlan2g" "phy1radio" + ;; kimax,u35wf) set_wifi_led "$boardname:blue:wifi" ucidef_set_led_netdev "eth" "ETH" "$boardname:green:eth" "eth0" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 67f2b4998a..d84e738e89 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -319,6 +319,10 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "5:lan" "0:wan" "6@eth0" ;; + iodata,wn-ac1167gr) + ucidef_add_switch "switch1" \ + "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0" + ;; kn_rf) ucidef_add_switch "switch0" \ "0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6@eth0" @@ -525,6 +529,9 @@ ramips_setup_macs() [ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address) wan_mac=$(macaddr_add "$lan_mac" 1) ;; + iodata,wn-ac1167gr) + wan_mac=$(macaddr_add "$(mtd_get_mac_binary Factory 4)" -1) + ;; iodata,wn-ax1167gr|\ iodata,wn-gx300gr) wan_mac=$(macaddr_add "$(mtd_get_mac_binary Factory 4)" 1) |