diff options
| author | Kyson Lok <kysonlok@gmail.com> | 2017-05-17 18:18:45 +0800 |
|---|---|---|
| committer | Mathias Kresin <dev@kresin.me> | 2017-05-26 08:04:15 +0200 |
| commit | abbfcc85259a4f6658c61e99dd3d2d3567e3eb3a (patch) | |
| tree | 005f2cb004e90efa6868b0c736edcfea265a5f92 /target/linux/ramips/base-files/etc/board.d | |
| parent | da472e5b30f63b7f214b1d646ef0d955cbf3f295 (diff) | |
| download | upstream-abbfcc85259a4f6658c61e99dd3d2d3567e3eb3a.tar.gz upstream-abbfcc85259a4f6658c61e99dd3d2d3567e3eb3a.tar.bz2 upstream-abbfcc85259a4f6658c61e99dd3d2d3567e3eb3a.zip | |
ramips: add support for GL-inet GL-MT300N-V2
This patch adds supports for the GL-inet GL-MT300N-V2.
Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)
Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.
Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.
Signed-off-by: Kyson Lok <kysonlok@gmail.com>
[match maximum image size with firmware partition]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Diffstat (limited to 'target/linux/ramips/base-files/etc/board.d')
| -rwxr-xr-x | target/linux/ramips/base-files/etc/board.d/01_leds | 3 | ||||
| -rwxr-xr-x | target/linux/ramips/base-files/etc/board.d/02_network | 4 |
2 files changed, 7 insertions, 0 deletions
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 2a35fc4bc2..b08f35268b 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -189,6 +189,9 @@ gl-mt300n|\ gl-mt750) set_wifi_led "$board:wlan" ;; +gl-mt300n-v2) + set_wifi_led "$board:red:wlan" + ;; hc5661|\ hc5661a) ucidef_set_led_default "system" "system" "$board:blue:system" "1" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 6d93f2ccaa..9dd5823639 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -180,6 +180,10 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0" ;; + gl-mt300n-v2) + ucidef_add_switch "switch0" \ + "1:lan" "0:wan" "6@eth0" + ;; awapn2403) ucidef_add_switch "switch0" \ "0:lan" "1:wan" "6@eth0" |