diff options
| author | Cezary Jackiewicz <cezary@eko.one.pl> | 2018-04-19 19:34:22 +0200 |
|---|---|---|
| committer | Mathias Kresin <dev@kresin.me> | 2018-08-15 07:42:36 +0200 |
| commit | 37af596593b0e84d0a076ab8f173066e3d7bc810 (patch) | |
| tree | fc009e33abc46962259afc72a392f7023889ef47 /target/linux/ramips/base-files/etc/board.d/02_network | |
| parent | 4877ad44c718debfa75533aedaaf3dfd0faeb6f0 (diff) | |
| download | upstream-37af596593b0e84d0a076ab8f173066e3d7bc810.tar.gz upstream-37af596593b0e84d0a076ab8f173066e3d7bc810.tar.bz2 upstream-37af596593b0e84d0a076ab8f173066e3d7bc810.zip | |
ramips: add support for D-Link DWR-118-A2
The DWR-118-A2 Wireless Router is based on the MT7620A SoC.
Specification:
- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612EN)
- 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN)
- 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN)
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader
Known issues:
- GELAN not working
- flash is very slow
The status led has been assigned to the dwr-118-a2:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.
Installation:
Apply factory image via http web-gui or JBOOT recovery page
How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Diffstat (limited to 'target/linux/ramips/base-files/etc/board.d/02_network')
| -rwxr-xr-x | target/linux/ramips/base-files/etc/board.d/02_network | 5 |
1 files changed, 5 insertions, 0 deletions
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 915c3584c5..b6f70ef50d 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -157,6 +157,10 @@ ramips_setup_interfaces() wrh-300cr) ucidef_set_interface_lan "eth0" ;; + dlink,dwr-118-a2) + ucidef_add_switch "switch0" \ + "1:lan:2" "2:lan:1" "3:lan:3" "4:lan" "0:wan" "6@eth0" + ;; mir3g) ucidef_add_switch "switch0" \ "2:lan:2" "3:lan:1" "1:wan" "6t@eth0" @@ -462,6 +466,7 @@ ramips_setup_macs() wan_mac=$(mtd_get_mac_ascii factory wanmac) ;; dlink,dwr-116-a1|\ + dlink,dwr-118-a2|\ dlink,dwr-921-c1) wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000) lan_mac=$(macaddr_add "$wan_mac" 1) |