lantiq: xrx200: use vlan for ethernet wan port

Using the lantiq,wan device tree property for one interface node and
the lantiq,switch device tree property for another interface node at
the same time was never intended/isn't supported at the moment.

The property is meant to be used in two phy operation mode where one
phy is assigned to an interface without lantiq,* device tree property
and the other phy is assigned to an interface with the lantiq,wan
device property to have two netdevs.

If both properties are used at the same time, the lantiq,wan interface
is shown as independent netdev but not able to operate independent. The
port needs to be managed via swconfig. These dependency is not obvious
and fooled already a lot of users.

Add a default WAN vlan for xrx200 devices having an ethernet WAN port
and remove the lantiq,wan device tree property. Leave it up to the user
to set the ethernet WAN port as default WAN interface or to use this
port as additional LAN port.

Signed-off-by: Mathias Kresin <dev@kresin.me>

4 files changed, 9 insertions, 39 deletions

diff --git a/target/linux/lantiq/base-files/etc/board.d/02_network b/target/linux/lantiq/base-files/etc/board.d/02_network
index 6140a16035..ff62c44219 100755
--- a/target/linux/lantiq/base-files/etc/board.d/02_network
+++ b/target/linux/lantiq/base-files/etc/board.d/02_network
@@ -78,7 +78,7 @@ BTHOMEHUBV5A)
 	lan_mac=$(mtd_get_mac_binary_ubi caldata 4364)
 	wan_mac=$(macaddr_add "$lan_mac" 1)
 	ucidef_add_switch "switch0" \
-		"0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "6t@eth0"
+		"0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "5:wan:5" "6t@eth0"
 	;;
 
 DGN3500*)
@@ -146,13 +146,13 @@ VR200v)
 VGV7510KW22*)
 	wan_mac=$(macaddr_add "$(mtd_get_mac_binary board_config 22)" 2)
 	ucidef_add_switch "switch0" \
-		"2:lan:2" "3:lan:1" "4:lan:4" "5:lan:3" "6t@eth0"
+		"2:lan:2" "3:lan:1" "4:lan:4" "5:lan:3" "0:wan:5" "6t@eth0"
 	;;
 
 VGV7519*)
 	wan_mac=$(mtd_get_mac_binary board_config 22)
 	ucidef_add_switch "switch0" \
-		"0:lan:4" "1:lan:3" "2:lan:2" "4:lan:1" "6t@eth0"
+		"0:lan:4" "1:lan:3" "2:lan:2" "4:lan:1" "5:wan:5" "6t@eth0"
 	;;
 
 WBMR)
diff --git a/target/linux/lantiq/dts/BTHOMEHUBV5A.dts b/target/linux/lantiq/dts/BTHOMEHUBV5A.dts
index 7f19e5291f..59b6cee9b8 100644
--- a/target/linux/lantiq/dts/BTHOMEHUBV5A.dts
+++ b/target/linux/lantiq/dts/BTHOMEHUBV5A.dts
@@ -244,15 +244,6 @@
 			phy-mode = "gmii";
 			phy-handle = <&phy13>;
 		};
-	};
-
-	wan: interface@1 {
-		compatible = "lantiq,xrx200-pdi";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <1>;
-		lantiq,wan;
-
 		ethernet@5 {
 			compatible = "lantiq,xrx200-pdi-port";
 			reg = <5>;
diff --git a/target/linux/lantiq/dts/VGV7510KW22.dtsi b/target/linux/lantiq/dts/VGV7510KW22.dtsi
index fa46e07670..cb1707e183 100644
--- a/target/linux/lantiq/dts/VGV7510KW22.dtsi
+++ b/target/linux/lantiq/dts/VGV7510KW22.dtsi
@@ -189,6 +189,12 @@
 		mtd-mac-address = <&boardconfig 0x16>;
 		lantiq,switch;
 
+		ethernet@0 {
+			compatible = "lantiq,xrx200-pdi-port";
+			reg = <0>;
+			phy-mode = "mii";
+			phy-handle = <&phy1>;
+		};
 		ethernet@2 {
 			compatible = "lantiq,xrx200-pdi-port";
 			reg = <2>;
@@ -215,23 +221,6 @@
 		};
 	};
 
-	wan: interface@1 {
-		compatible = "lantiq,xrx200-pdi";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <1>;
-		mtd-mac-address = <&boardconfig 0x16>;
-		mtd-mac-address-increment = <3>;
-		lantiq,wan;
-
-		ethernet@0 {
-			compatible = "lantiq,xrx200-pdi-port";
-			reg = <0>;
-			phy-mode = "mii";
-			phy-handle = <&phy1>;
-		};
-	};
-
 	mdio@0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/target/linux/lantiq/dts/VGV7519.dtsi b/target/linux/lantiq/dts/VGV7519.dtsi
index 9080d8d997..93d5a9473a 100644
--- a/target/linux/lantiq/dts/VGV7519.dtsi
+++ b/target/linux/lantiq/dts/VGV7519.dtsi
@@ -260,16 +260,6 @@
 			phy-mode = "gmii";
 			phy-handle = <&phy13>;
 		};
-	};
-
-	wan: interface@1 {
-		compatible = "lantiq,xrx200-pdi";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <1>;
-		mtd-mac-address = <&boardconfig 0x16>;
-		lantiq,wan;
-
 		ethernet@5 {
 			compatible = "lantiq,xrx200-pdi-port";
 			reg = <5>;