lantiq: bump to 3.1

SVN-Revision: 28721

1 files changed, 890 insertions, 0 deletions

diff --git a/target/linux/lantiq/patches/0011-MIPS-lantiq-adds-falcon-I2C.patch b/target/linux/lantiq/patches/0011-MIPS-lantiq-adds-falcon-I2C.patch
new file mode 100644
index 0000000000..eceb1e4f2e
--- /dev/null
+++ b/target/linux/lantiq/patches/0011-MIPS-lantiq-adds-falcon-I2C.patch
@@ -0,0 +1,890 @@
+From 6437f41dfdf9475178e22ab0dd886af033f90cc2 Mon Sep 17 00:00:00 2001
+From: John Crispin <blogic@openwrt.org>
+Date: Thu, 29 Sep 2011 21:10:16 +0200
+Subject: [PATCH 11/24] MIPS: lantiq: adds falcon I2C
+
+---
+ arch/mips/lantiq/falcon/devices.c |   21 +
+ arch/mips/lantiq/falcon/devices.h |    1 +
+ drivers/i2c/busses/Kconfig        |    4 +
+ drivers/i2c/busses/Makefile       |    1 +
+ drivers/i2c/busses/i2c-falcon.c   |  815 +++++++++++++++++++++++++++++++++++++
+ 5 files changed, 842 insertions(+), 0 deletions(-)
+ create mode 100644 drivers/i2c/busses/i2c-falcon.c
+
+--- a/arch/mips/lantiq/falcon/devices.c
++++ b/arch/mips/lantiq/falcon/devices.c
+@@ -126,3 +126,24 @@ falcon_register_gpio_extra(void)
+ 	ltq_sysctl_activate(SYSCTL_SYS1,
+ 		ACTS_PADCTRL3 | ACTS_PADCTRL4 | ACTS_P3 | ACTS_P4);
+ }
++
++/* i2c */
++static struct resource falcon_i2c_resources[] = {
++	MEM_RES("i2c", GPON_I2C_BASE,GPON_I2C_END),
++	IRQ_RES("i2c_lb", FALCON_IRQ_I2C_LBREQ),
++	IRQ_RES("i2c_b", FALCON_IRQ_I2C_BREQ),
++	IRQ_RES("i2c_err", FALCON_IRQ_I2C_I2C_ERR),
++	IRQ_RES("i2c_p", FALCON_IRQ_I2C_I2C_P),
++};
++
++void __init falcon_register_i2c(void)
++{
++	platform_device_register_simple("i2c-falcon", 0,
++	falcon_i2c_resources, ARRAY_SIZE(falcon_i2c_resources));
++	sys1_hw_activate(ACTS_I2C_ACT);
++}
++
++void __init falcon_register_crypto(void)
++{
++	platform_device_register_simple("ltq_falcon_deu", 0, NULL, 0);
++}
+--- a/arch/mips/lantiq/falcon/devices.h
++++ b/arch/mips/lantiq/falcon/devices.h
+@@ -16,5 +16,6 @@
+ extern void falcon_register_nand(void);
+ extern void falcon_register_gpio(void);
+ extern void falcon_register_gpio_extra(void);
++extern void falcon_register_i2c(void);
+ 
+ #endif
+--- a/drivers/i2c/busses/Kconfig
++++ b/drivers/i2c/busses/Kconfig
+@@ -284,6 +284,10 @@ config I2C_POWERMAC
+ 
+ comment "I2C system bus drivers (mostly embedded / system-on-chip)"
+ 
++config I2C_FALCON
++	tristate "Falcon I2C interface"
++#	depends on SOC_FALCON
++
+ config I2C_AT91
+ 	tristate "Atmel AT91 I2C Two-Wire interface (TWI)"
+ 	depends on ARCH_AT91 && EXPERIMENTAL && BROKEN
+--- a/drivers/i2c/busses/Makefile
++++ b/drivers/i2c/busses/Makefile
+@@ -82,5 +82,6 @@ obj-$(CONFIG_I2C_SIBYTE)	+= i2c-sibyte.o
+ obj-$(CONFIG_I2C_STUB)		+= i2c-stub.o
+ obj-$(CONFIG_SCx200_ACB)	+= scx200_acb.o
+ obj-$(CONFIG_SCx200_I2C)	+= scx200_i2c.o
++obj-$(CONFIG_I2C_FALCON)	+= i2c-falcon.o
+ 
+ ccflags-$(CONFIG_I2C_DEBUG_BUS) := -DDEBUG
+--- /dev/null
++++ b/drivers/i2c/busses/i2c-falcon.c
+@@ -0,0 +1,815 @@
++/*
++ * Lantiq FALC(tm) ON - I2C bus adapter
++ *
++ * Parts based on i2c-designware.c and other i2c drivers from Linux 2.6.33
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
++ */
++
++/* #define DEBUG */
++
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/delay.h>
++#include <linux/slab.h> /* for kzalloc, kfree */
++#include <linux/i2c.h>
++#include <linux/clk.h>
++#include <linux/errno.h>
++#include <linux/sched.h>
++#include <linux/err.h>
++#include <linux/interrupt.h>
++#include <linux/platform_device.h>
++#include <linux/io.h>
++#include <linux/gpio.h>
++
++#include <falcon/lantiq_soc.h>
++
++/* CURRENT ISSUES:
++ * - no high speed support
++ * - supports only master mode
++ * - ten bit mode is not tested (no slave devices)
++ */
++
++/* mapping for access macros */
++#define reg_r32(reg)		__raw_readl(reg)
++#define reg_w32(val, reg)	__raw_writel(val, reg)
++#define reg_w32_mask(clear, set, reg)	\
++				reg_w32((reg_r32(reg) & ~(clear)) | (set), reg)
++#define reg_r32_table(reg, idx) reg_r32(&((uint32_t *)&reg)[idx])
++#define reg_w32_table(val, reg, idx) reg_w32(val, &((uint32_t *)&reg)[idx])
++#define i2c	(priv->membase)
++#include <falcon/i2c_reg.h>
++
++#define DRV_NAME "i2c-falcon"
++#define DRV_VERSION "1.01"
++
++#define FALCON_I2C_BUSY_TIMEOUT		20 /* ms */
++
++#ifdef DEBUG
++#define FALCON_I2C_XFER_TIMEOUT		25*HZ
++#else
++#define FALCON_I2C_XFER_TIMEOUT		HZ
++#endif
++#if defined(DEBUG) && 0
++#define PRINTK(arg...) printk(arg)
++#else
++#define PRINTK(arg...) do {} while (0)
++#endif
++
++#define FALCON_I2C_IMSC_DEFAULT_MASK	(I2C_IMSC_I2C_P_INT_EN | \
++					 I2C_IMSC_I2C_ERR_INT_EN)
++
++#define FALCON_I2C_ARB_LOST	(1 << 0)
++#define FALCON_I2C_NACK		(1 << 1)
++#define FALCON_I2C_RX_UFL	(1 << 2)
++#define FALCON_I2C_RX_OFL	(1 << 3)
++#define FALCON_I2C_TX_UFL	(1 << 4)
++#define FALCON_I2C_TX_OFL	(1 << 5)
++
++struct falcon_i2c {
++	struct mutex mutex;
++
++	enum {
++		FALCON_I2C_MODE_100	= 1,
++		FALCON_I2C_MODE_400	= 2,
++		FALCON_I2C_MODE_3400	= 3
++	} mode;				/* current speed mode */
++
++	struct clk *clk;		/* clock input for i2c hardware block */
++	struct gpon_reg_i2c __iomem *membase;	/* base of mapped registers */
++	int irq_lb, irq_b, irq_err, irq_p;	/* last burst, burst, error,
++						   protocol IRQs */
++
++	struct i2c_adapter adap;
++	struct device *dev;
++
++	struct completion	cmd_complete;
++
++	/* message transfer data */
++	/* current message */
++	struct i2c_msg		*current_msg;
++	/* number of messages to handle */
++	int			msgs_num;
++	/* current buffer */
++	u8			*msg_buf;
++	/* remaining length of current buffer */
++	u32			msg_buf_len;
++	/* error status of the current transfer */
++	int			msg_err;
++
++	/* master status codes */
++	enum {
++		STATUS_IDLE,
++		STATUS_ADDR,	/* address phase */
++		STATUS_WRITE,
++		STATUS_READ,
++		STATUS_READ_END,
++		STATUS_STOP
++	} status;
++};
++
++static irqreturn_t falcon_i2c_isr(int irq, void *dev_id);
++
++static inline void enable_burst_irq(struct falcon_i2c *priv)
++{
++	i2c_w32_mask(0, I2C_IMSC_LBREQ_INT_EN | I2C_IMSC_BREQ_INT_EN, imsc);
++}
++static inline void disable_burst_irq(struct falcon_i2c *priv)
++{
++	i2c_w32_mask(I2C_IMSC_LBREQ_INT_EN | I2C_IMSC_BREQ_INT_EN, 0, imsc);
++}
++
++static void prepare_msg_send_addr(struct falcon_i2c *priv)
++{
++	struct i2c_msg *msg = priv->current_msg;
++	int rd = !!(msg->flags & I2C_M_RD);	/* extends to 0 or 1 */
++	u16 addr = msg->addr;
++
++	/* new i2c_msg */
++	priv->msg_buf = msg->buf;
++	priv->msg_buf_len = msg->len;
++	if (rd)
++		priv->status = STATUS_READ;
++	else
++		priv->status = STATUS_WRITE;
++
++	/* send slave address */
++	if (msg->flags & I2C_M_TEN) {
++		i2c_w32(0xf0 | ((addr & 0x300) >> 7) | rd, txd);
++		i2c_w32(addr & 0xff, txd);
++	} else
++		i2c_w32((addr & 0x7f) << 1 | rd, txd);
++}
++
++static void set_tx_len(struct falcon_i2c *priv)
++{
++	struct i2c_msg *msg = priv->current_msg;
++	int len = (msg->flags & I2C_M_TEN) ? 2 : 1;
++
++	PRINTK("set_tx_len %cX\n", (msg->flags & I2C_M_RD)?'R':'T');
++
++	priv->status = STATUS_ADDR;
++
++	if (!(msg->flags & I2C_M_RD)) {
++		len += msg->len;
++	} else {
++		/* set maximum received packet size (before rx int!) */
++		i2c_w32(msg->len, mrps_ctrl);
++	}
++	i2c_w32(len, tps_ctrl);
++	enable_burst_irq(priv);
++}
++
++static int falcon_i2c_hw_init(struct i2c_adapter *adap)
++{
++	struct falcon_i2c *priv = i2c_get_adapdata(adap);
++
++	/* disable bus */
++	i2c_w32_mask(I2C_RUN_CTRL_RUN_EN, 0, run_ctrl);
++
++#ifndef DEBUG
++	/* set normal operation clock divider */
++	i2c_w32(1 << I2C_CLC_RMC_OFFSET, clc);
++#else
++	/* for debugging a higher divider value! */
++	i2c_w32(0xF0 << I2C_CLC_RMC_OFFSET, clc);
++#endif
++
++	/* set frequency */
++	if (priv->mode == FALCON_I2C_MODE_100) {
++		dev_dbg(priv->dev, "set standard mode (100 kHz)\n");
++		i2c_w32(0, fdiv_high_cfg);
++		i2c_w32((1 << I2C_FDIV_CFG_INC_OFFSET) |
++			(499 << I2C_FDIV_CFG_DEC_OFFSET),
++			fdiv_cfg);
++	} else if (priv->mode == FALCON_I2C_MODE_400) {
++		dev_dbg(priv->dev, "set fast mode (400 kHz)\n");
++		i2c_w32(0, fdiv_high_cfg);
++		i2c_w32((1 << I2C_FDIV_CFG_INC_OFFSET) |
++			(124 << I2C_FDIV_CFG_DEC_OFFSET),
++			fdiv_cfg);
++	} else if (priv->mode == FALCON_I2C_MODE_3400) {
++		dev_dbg(priv->dev, "set high mode (3.4 MHz)\n");
++		i2c_w32(0, fdiv_cfg);
++		/* TODO recalculate value for 100MHz input */
++		i2c_w32((41 << I2C_FDIV_HIGH_CFG_INC_OFFSET) |
++			(152 << I2C_FDIV_HIGH_CFG_DEC_OFFSET),
++			fdiv_high_cfg);
++	} else {
++		dev_warn(priv->dev, "unknown mode\n");
++		return -ENODEV;
++	}
++
++	/* configure fifo */
++	i2c_w32(I2C_FIFO_CFG_TXFC | /* tx fifo as flow controller */
++		I2C_FIFO_CFG_RXFC | /* rx fifo as flow controller */
++		I2C_FIFO_CFG_TXFA_TXFA2 | /* tx fifo 4-byte aligned */
++		I2C_FIFO_CFG_RXFA_RXFA2 | /* rx fifo 4-byte aligned */
++		I2C_FIFO_CFG_TXBS_TXBS0 | /* tx fifo burst size is 1 word */
++		I2C_FIFO_CFG_RXBS_RXBS0,  /* rx fifo burst size is 1 word */
++		fifo_cfg);
++
++	/* configure address */
++	i2c_w32(I2C_ADDR_CFG_SOPE_EN |	/* generate stop when no more data in the
++					   fifo */
++		I2C_ADDR_CFG_SONA_EN |	/* generate stop when NA received */
++		I2C_ADDR_CFG_MnS_EN |	/* we are master device */
++		0,			/* our slave address (not used!) */
++		addr_cfg);
++
++	/* enable bus */
++	i2c_w32_mask(0, I2C_RUN_CTRL_RUN_EN, run_ctrl);
++
++	return 0;
++}
++
++static int falcon_i2c_wait_bus_not_busy(struct falcon_i2c *priv)
++{
++	int timeout = FALCON_I2C_BUSY_TIMEOUT;
++
++	while ((i2c_r32(bus_stat) & I2C_BUS_STAT_BS_MASK)
++				 != I2C_BUS_STAT_BS_FREE) {
++		if (timeout <= 0) {
++			dev_warn(priv->dev, "timeout waiting for bus ready\n");
++			return -ETIMEDOUT;
++		}
++		timeout--;
++		mdelay(1);
++	}
++
++	return 0;
++}
++
++static void falcon_i2c_tx(struct falcon_i2c *priv, int last)
++{
++	if (priv->msg_buf_len && priv->msg_buf) {
++		i2c_w32(*priv->msg_buf, txd);
++
++		if (--priv->msg_buf_len)
++			priv->msg_buf++;
++		else
++			priv->msg_buf = NULL;
++	} else
++		last = 1;
++
++	if (last) {
++		disable_burst_irq(priv);
++	}
++}
++
++static void falcon_i2c_rx(struct falcon_i2c *priv, int last)
++{
++	u32 fifo_stat,timeout;
++	if (priv->msg_buf_len && priv->msg_buf) {
++		timeout = 5000000;
++		do {
++			fifo_stat = i2c_r32(ffs_stat);
++		} while (!fifo_stat && --timeout);
++		if (!timeout) {
++			last = 1;
++			PRINTK("\nrx timeout\n");
++			goto err;
++		}
++		while (fifo_stat) {
++			*priv->msg_buf = i2c_r32(rxd);
++			if (--priv->msg_buf_len)
++				priv->msg_buf++;
++			else {
++				priv->msg_buf = NULL;
++				last = 1;
++				break;
++			}
++			#if 0
++			fifo_stat = i2c_r32(ffs_stat);
++			#else
++			/* do not read more than burst size, otherwise no "last
++			burst" is generated and the transaction is blocked! */
++			fifo_stat = 0;
++			#endif
++		}
++	} else {
++		last = 1;
++	}
++err:
++	if (last) {
++		disable_burst_irq(priv);
++
++		if (priv->status == STATUS_READ_END) {
++			/* do the STATUS_STOP and complete() here, as sometimes
++			   the tx_end is already seen before this is finished */
++			priv->status = STATUS_STOP;
++			complete(&priv->cmd_complete);
++		} else {
++			i2c_w32(I2C_ENDD_CTRL_SETEND, endd_ctrl);
++			priv->status = STATUS_READ_END;
++		}
++	}
++}
++
++static void falcon_i2c_xfer_init(struct falcon_i2c *priv)
++{
++	/* enable interrupts */
++	i2c_w32(FALCON_I2C_IMSC_DEFAULT_MASK, imsc);
++
++	/* trigger transfer of first msg */
++	set_tx_len(priv);
++}
++
++static void dump_msgs(struct i2c_msg msgs[], int num, int rx)
++{
++#if defined(DEBUG)
++	int i, j;
++	printk("Messages %d %s\n", num, rx ? "out" : "in");
++	for (i = 0; i < num; i++) {
++		printk("%2d %cX Msg(%d) addr=0x%X: ", i,
++			(msgs[i].flags & I2C_M_RD)?'R':'T',
++			msgs[i].len, msgs[i].addr);
++		if (!(msgs[i].flags & I2C_M_RD) || rx) {
++			for (j = 0; j < msgs[i].len; j++)
++				printk("%02X ", msgs[i].buf[j]);
++		}
++		printk("\n");
++	}
++#endif
++}
++
++static void falcon_i2c_release_bus(struct falcon_i2c *priv)
++{
++	if ((i2c_r32(bus_stat) & I2C_BUS_STAT_BS_MASK) == I2C_BUS_STAT_BS_BM)
++		i2c_w32(I2C_ENDD_CTRL_SETEND, endd_ctrl);
++}
++
++static int falcon_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
++			   int num)
++{
++	struct falcon_i2c *priv = i2c_get_adapdata(adap);
++	int ret;
++
++	dev_dbg(priv->dev, "xfer %u messages\n", num);
++	dump_msgs(msgs, num, 0);
++
++	mutex_lock(&priv->mutex);
++
++	INIT_COMPLETION(priv->cmd_complete);
++	priv->current_msg = msgs;
++	priv->msgs_num = num;
++	priv->msg_err = 0;
++	priv->status = STATUS_IDLE;
++
++	/* wait for the bus to become ready */
++	ret = falcon_i2c_wait_bus_not_busy(priv);
++	if (ret)
++		goto done;
++
++	while (priv->msgs_num) {
++		/* start the transfers */
++		falcon_i2c_xfer_init(priv);
++
++		/* wait for transfers to complete */
++		ret = wait_for_completion_interruptible_timeout(
++			&priv->cmd_complete, FALCON_I2C_XFER_TIMEOUT);
++		if (ret == 0) {
++			dev_err(priv->dev, "controller timed out\n");
++			falcon_i2c_hw_init(adap);
++			ret = -ETIMEDOUT;
++			goto done;
++		} else if (ret < 0)
++			goto done;
++
++		if (priv->msg_err) {
++			if (priv->msg_err & FALCON_I2C_NACK)
++				ret = -ENXIO;
++			else
++				ret = -EREMOTEIO;
++			goto done;
++		}
++		if (--priv->msgs_num) {
++			priv->current_msg++;
++		}
++	}
++	/* no error? */
++	ret = num;
++
++done:
++	falcon_i2c_release_bus(priv);
++
++	mutex_unlock(&priv->mutex);
++
++	if (ret>=0)
++		dump_msgs(msgs, num, 1);
++
++	PRINTK("XFER ret %d\n", ret);
++	return ret;
++}
++
++static irqreturn_t falcon_i2c_isr_burst(int irq, void *dev_id)
++{
++	struct falcon_i2c *priv = dev_id;
++	struct i2c_msg *msg = priv->current_msg;
++	int last = (irq == priv->irq_lb);
++
++	if (last)
++		PRINTK("LB ");
++	else
++		PRINTK("B ");
++
++	if (msg->flags & I2C_M_RD) {
++		switch (priv->status) {
++		case STATUS_ADDR:
++			PRINTK("X");
++			prepare_msg_send_addr(priv);
++			disable_burst_irq(priv);
++			break;
++		case STATUS_READ:
++		case STATUS_READ_END:
++			PRINTK("R");
++			falcon_i2c_rx(priv, last);
++			break;
++		default:
++			disable_burst_irq(priv);
++			printk("Status R %d\n", priv->status);
++			break;
++		}
++	} else {
++		switch (priv->status) {
++		case STATUS_ADDR:
++			PRINTK("x");
++			prepare_msg_send_addr(priv);
++			break;
++		case STATUS_WRITE:
++			PRINTK("w");
++			falcon_i2c_tx(priv, last);
++			break;
++		default:
++			disable_burst_irq(priv);
++			printk("Status W %d\n", priv->status);
++			break;
++		}
++	}
++
++	i2c_w32(I2C_ICR_BREQ_INT_CLR | I2C_ICR_LBREQ_INT_CLR, icr);
++	return IRQ_HANDLED;
++}
++
++static void falcon_i2c_isr_prot(struct falcon_i2c *priv)
++{
++	u32 i_pro = i2c_r32(p_irqss);
++
++	PRINTK("i2c-p");
++
++	/* not acknowledge */
++	if (i_pro & I2C_P_IRQSS_NACK) {
++		priv->msg_err |= FALCON_I2C_NACK;
++		PRINTK(" nack");
++	}
++
++	/* arbitration lost */
++	if (i_pro & I2C_P_IRQSS_AL) {
++		priv->msg_err |= FALCON_I2C_ARB_LOST;
++		PRINTK(" arb-lost");
++	}
++	/* tx -> rx switch */
++	if (i_pro & I2C_P_IRQSS_RX)
++		PRINTK(" rx");
++
++	/* tx end */
++	if (i_pro & I2C_P_IRQSS_TX_END)
++		PRINTK(" txend");
++	PRINTK("\n");
++
++	if (!priv->msg_err) {
++		/* tx -> rx switch */
++		if (i_pro & I2C_P_IRQSS_RX) {
++			priv->status = STATUS_READ;
++			enable_burst_irq(priv);
++		}
++		if (i_pro & I2C_P_IRQSS_TX_END) {
++			if (priv->status == STATUS_READ)
++				priv->status = STATUS_READ_END;
++			else {
++				disable_burst_irq(priv);
++				priv->status = STATUS_STOP;
++			}
++		}
++	}
++
++	i2c_w32(i_pro, p_irqsc);
++}
++
++static irqreturn_t falcon_i2c_isr(int irq, void *dev_id)
++{
++	u32 i_raw, i_err=0;
++	struct falcon_i2c *priv = dev_id;
++
++	i_raw = i2c_r32(mis);
++	PRINTK("i_raw 0x%08X\n", i_raw);
++
++	/* error interrupt */
++	if (i_raw & I2C_RIS_I2C_ERR_INT_INTOCC) {
++		i_err = i2c_r32(err_irqss);
++		PRINTK("i_err 0x%08X bus_stat 0x%04X\n",
++			i_err, i2c_r32(bus_stat));
++
++		/* tx fifo overflow (8) */
++		if (i_err & I2C_ERR_IRQSS_TXF_OFL)
++			priv->msg_err |= FALCON_I2C_TX_OFL;
++
++		/* tx fifo underflow (4) */
++		if (i_err & I2C_ERR_IRQSS_TXF_UFL)
++			priv->msg_err |= FALCON_I2C_TX_UFL;
++
++		/* rx fifo overflow (2) */
++		if (i_err & I2C_ERR_IRQSS_RXF_OFL)
++			priv->msg_err |= FALCON_I2C_RX_OFL;
++
++		/* rx fifo underflow (1) */
++		if (i_err & I2C_ERR_IRQSS_RXF_UFL)
++			priv->msg_err |= FALCON_I2C_RX_UFL;
++
++		i2c_w32(i_err, err_irqsc);
++	}
++
++	/* protocol interrupt */
++	if (i_raw & I2C_RIS_I2C_P_INT_INTOCC)
++		falcon_i2c_isr_prot(priv);
++
++	if ((priv->msg_err) || (priv->status == STATUS_STOP))
++		complete(&priv->cmd_complete);
++
++	return IRQ_HANDLED;
++}
++
++static u32 falcon_i2c_functionality(struct i2c_adapter *adap)
++{
++	return	I2C_FUNC_I2C |
++		I2C_FUNC_10BIT_ADDR |
++		I2C_FUNC_SMBUS_EMUL;
++}
++
++static struct i2c_algorithm falcon_i2c_algorithm = {
++	.master_xfer	= falcon_i2c_xfer,
++	.functionality	= falcon_i2c_functionality,
++};
++
++static int __devinit falcon_i2c_probe(struct platform_device *pdev)
++{
++	int ret = 0;
++	struct falcon_i2c *priv;
++	struct i2c_adapter *adap;
++	struct resource *mmres, *ioarea,
++			*irqres_lb, *irqres_b, *irqres_err, *irqres_p;
++	struct clk *clk;
++
++	dev_dbg(&pdev->dev, "probing\n");
++
++	mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	irqres_lb = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
++						 "i2c_lb");
++	irqres_b = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "i2c_b");
++	irqres_err = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
++						  "i2c_err");
++	irqres_p = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "i2c_p");
++
++	if (!mmres || !irqres_lb || !irqres_b || !irqres_err || !irqres_p) {
++		dev_err(&pdev->dev, "no resources\n");
++		return -ENODEV;
++	}
++
++	clk = clk_get(&pdev->dev, "fpi");
++	if (IS_ERR(clk)) {
++		dev_err(&pdev->dev, "failed to get fpi clk\n");
++		return -ENOENT;
++	}
++
++	if (clk_get_rate(clk) != 100000000) {
++		dev_err(&pdev->dev, "input clock is not 100MHz\n");
++		return -ENOENT;
++	}
++
++	/* allocate private data */
++	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
++	if (!priv) {
++		dev_err(&pdev->dev, "can't allocate private data\n");
++		return -ENOMEM;
++	}
++
++	adap = &priv->adap;
++	i2c_set_adapdata(adap, priv);
++	adap->owner = THIS_MODULE;
++	adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
++	strlcpy(adap->name, DRV_NAME "-adapter", sizeof(adap->name));
++	adap->algo = &falcon_i2c_algorithm;
++
++	priv->mode = FALCON_I2C_MODE_100;
++	priv->clk = clk;
++	priv->dev = &pdev->dev;
++
++	init_completion(&priv->cmd_complete);
++	mutex_init(&priv->mutex);
++
++	ret = ltq_gpio_request(107, 0, 0, 0, DRV_NAME":sda");
++	if (ret) {
++		dev_err(&pdev->dev, "I2C gpio 107 (sda) not available\n");
++		ret = -ENXIO;
++		goto err_free_priv;
++	}
++	ret = ltq_gpio_request(108, 0, 0, 0, DRV_NAME":scl");
++	if (ret) {
++		gpio_free(107);
++		dev_err(&pdev->dev, "I2C gpio 108 (scl) not available\n");
++		ret = -ENXIO;
++		goto err_free_priv;
++	}
++
++	ioarea = request_mem_region(mmres->start, resource_size(mmres),
++					 pdev->name);
++
++	if (ioarea == NULL) {
++		dev_err(&pdev->dev, "I2C region already claimed\n");
++		ret = -ENXIO;
++		goto err_free_gpio;
++	}
++
++	/* map memory */
++	priv->membase = ioremap_nocache(mmres->start & ~KSEG1,
++		resource_size(mmres));
++	if (priv->membase == NULL) {
++		ret = -ENOMEM;
++		goto err_release_region;
++	}
++
++	priv->irq_lb = irqres_lb->start;
++	ret = request_irq(priv->irq_lb, falcon_i2c_isr_burst, IRQF_DISABLED,
++			  irqres_lb->name, priv);
++	if (ret) {
++		dev_err(&pdev->dev, "can't get last burst IRQ %d\n", irqres_lb->start);
++		ret = -ENODEV;
++		goto err_unmap_mem;
++	}
++
++	priv->irq_b = irqres_b->start;
++	ret = request_irq(priv->irq_b, falcon_i2c_isr_burst, IRQF_DISABLED,
++			  irqres_b->name, priv);
++	if (ret) {
++		dev_err(&pdev->dev, "can't get burst IRQ %d\n", irqres_b->start);
++		ret = -ENODEV;
++		goto err_free_lb_irq;
++	}
++
++	priv->irq_err = irqres_err->start;
++	ret = request_irq(priv->irq_err, falcon_i2c_isr, IRQF_DISABLED,
++			  irqres_err->name, priv);
++	if (ret) {
++		dev_err(&pdev->dev, "can't get error IRQ %d\n", irqres_err->start);
++		ret = -ENODEV;
++		goto err_free_b_irq;
++	}
++
++	priv->irq_p = irqres_p->start;
++	ret = request_irq(priv->irq_p, falcon_i2c_isr, IRQF_DISABLED,
++			  irqres_p->name, priv);
++	if (ret) {
++		dev_err(&pdev->dev, "can't get protocol IRQ %d\n", irqres_p->start);
++		ret = -ENODEV;
++		goto err_free_err_irq;
++	}
++
++	dev_dbg(&pdev->dev, "mapped io-space to %p\n", priv->membase);
++	dev_dbg(&pdev->dev, "use IRQs %d, %d, %d, %d\n", irqres_lb->start,
++	    irqres_b->start, irqres_err->start, irqres_p->start);
++
++	/* add our adapter to the i2c stack */
++	ret = i2c_add_numbered_adapter(adap);
++	if (ret) {
++		dev_err(&pdev->dev, "can't register I2C adapter\n");
++		goto err_free_p_irq;
++	}
++
++	platform_set_drvdata(pdev, priv);
++	i2c_set_adapdata(adap, priv);
++
++	/* print module version information */
++	dev_dbg(&pdev->dev, "module id=%u revision=%u\n",
++		(i2c_r32(id) & I2C_ID_ID_MASK) >> I2C_ID_ID_OFFSET,
++		(i2c_r32(id) & I2C_ID_REV_MASK) >> I2C_ID_REV_OFFSET);
++
++	/* initialize HW */
++	ret = falcon_i2c_hw_init(adap);
++	if (ret) {
++		dev_err(&pdev->dev, "can't configure adapter\n");
++		goto err_remove_adapter;
++	}
++
++	dev_info(&pdev->dev, "version %s\n", DRV_VERSION);
++
++	return 0;
++
++err_remove_adapter:
++	i2c_del_adapter(adap);
++	platform_set_drvdata(pdev, NULL);
++
++err_free_p_irq:
++	free_irq(priv->irq_p, priv);
++
++err_free_err_irq:
++	free_irq(priv->irq_err, priv);
++
++err_free_b_irq:
++	free_irq(priv->irq_b, priv);
++
++err_free_lb_irq:
++	free_irq(priv->irq_lb, priv);
++
++err_unmap_mem:
++	iounmap(priv->membase);
++
++err_release_region:
++	release_mem_region(mmres->start, resource_size(mmres));
++
++err_free_gpio:
++	gpio_free(108);
++	gpio_free(107);
++
++err_free_priv:
++	kfree(priv);
++
++	return ret;
++}
++
++static int __devexit falcon_i2c_remove(struct platform_device *pdev)
++{
++	struct falcon_i2c *priv = platform_get_drvdata(pdev);
++	struct resource *mmres;
++
++	/* disable bus */
++	i2c_w32_mask(I2C_RUN_CTRL_RUN_EN, 0, run_ctrl);
++
++	/* remove driver */
++	platform_set_drvdata(pdev, NULL);
++	i2c_del_adapter(&priv->adap);
++
++	free_irq(priv->irq_lb, priv);
++	free_irq(priv->irq_b, priv);
++	free_irq(priv->irq_err, priv);
++	free_irq(priv->irq_p, priv);
++
++	iounmap(priv->membase);
++
++	gpio_free(108);
++	gpio_free(107);
++
++	kfree(priv);
++
++	mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	release_mem_region(mmres->start, resource_size(mmres));
++
++	dev_dbg(&pdev->dev, "removed\n");
++
++	return 0;
++}
++
++static struct platform_driver falcon_i2c_driver = {
++	.probe	= falcon_i2c_probe,
++	.remove	= __devexit_p(falcon_i2c_remove),
++	.driver	= {
++		.name	= DRV_NAME,
++		.owner	= THIS_MODULE,
++	},
++};
++
++static int __init falcon_i2c_init(void)
++{
++	int ret;
++
++	ret = platform_driver_register(&falcon_i2c_driver);
++
++	if (ret)
++		pr_debug(DRV_NAME ": can't register platform driver\n");
++
++	return ret;
++}
++
++static void __exit falcon_i2c_exit(void)
++{
++	platform_driver_unregister(&falcon_i2c_driver);
++}
++
++module_init(falcon_i2c_init);
++module_exit(falcon_i2c_exit);
++
++MODULE_DESCRIPTION("Lantiq FALC(tm) ON - I2C bus adapter");
++MODULE_ALIAS("platform:" DRV_NAME);
++MODULE_LICENSE("GPL");
++MODULE_VERSION(DRV_VERSION);