aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/lantiq/base-files
diff options
context:
space:
mode:
authorMathias Kresin <dev@kresin.me>2017-06-09 19:28:36 +0200
committerMathias Kresin <dev@kresin.me>2018-05-17 07:40:19 +0200
commit0b62fe5ed87ecac52301096b15abb69f96117c8c (patch)
treed18f32394a3890198e4c28e5a72b4c340b69aa84 /target/linux/lantiq/base-files
parentd7b7483343b5c7f157a2a97244ce9e60f4260e43 (diff)
downloadupstream-0b62fe5ed87ecac52301096b15abb69f96117c8c.tar.gz
upstream-0b62fe5ed87ecac52301096b15abb69f96117c8c.tar.bz2
upstream-0b62fe5ed87ecac52301096b15abb69f96117c8c.zip
lantiq: complete AVM FRITZ!Box 3370 support
Rename the image and use a compatible string which indicates that only hardware revision 2 and higher is supported. It allows to use the wireless LED, as HWRev 1 uses GPIO#39 for the wireless LED and starting with HWRev 2 GPIO#35 is used for the wireless LED and GPIO#39 for IFX_GPIO_MODULE_EXTPHY_MDIO. The HWREV can be checked by connecting to the fritzbox right after power on via ftp: ftp> quote GETENV HWSubRevision Within the same HW revision 5 of the Fritz!Box 3370 different NAND flash chips are used. Usually it isn't a big deal but depending on the used NAND flash chip, the ECC calculation is done different (and incompatible of course). Boards with a Micron MT29F1G08ABADA NAND flash chip are using the NAND chip to calculate the ECC (on-die). Boards with a Hynix HY27UF081G2M NAND flash chip are doing the ECC calculation in software. Supporting both with a single DTS isn't possible. It might be possible to add a patch selecting the ECC mode dynamicaly based on the found NAND flash chip. But such a patch has no chance to get accepted upstream and most likely need to be touched with every kernel update. Instead two images are created. One for Micron NAND flash chip and one for Hynix NAND flash chip. So far no pattern is known to identify the used flash chip without opening the box. Add the power off GPIO. At least EVA version 2186 sets/keeps the GPIO as input, which will cause a reboot 30sec after power on. For boards with EVA version 2186 the installation is tricky as it has to be finished within the 30sec time frame. The EVA version can be checked by connecting to the fritzbox right after power on via ftp: ftp> quote GETENV urlader-version The ath9k eeprom/caldata is at a different and offset and stored in reverse order (from the last byte to the beginning) on the flash. Reverse the bits to bring the data into the format expected by the ath9k driver. Since the ath9k eeprom is stored in reverse order on flash, we can not use the mac address from the on flash eeprom. Get the MAC address from the tffs instead. Within the same HW revision 5 of the Fritz!Box 3370 both version of the vr9 SoC are used. During preparation of kernel 4.14 support, all devicetree source files were changed to load the vr9 v1.1 and vr9 v1.2 gphy firmware, which fixed the embedded phys for boards using the version 1.2 of the vr9 SoC. While at it, add a trigger to make use of the LAN LED. Setup the build-in switch and add a hint for LuCI two show the ports in order matching the labels on the case Add support for the second USB port and provide the volatage GPIOs. Use GPIO#21 as PCIe reset pin. The lan led is connected to GPIO#38. Name the rootfs partition ubi and remove the mtd/rootfs related kernel bootargs to use the OpenWrt autoprobing based on the partition name. Enable sysupgrade support to allow an upgrade from a running system. Since sysupgrade wasn't supported till now, drop image build code which was added to allow a sysupgrade from earlier OpenWrt versions. Build images that allow an (initial) installation via EVA bootloader. To install OpenWrt via Eva bootloader, within the first seconds after power on a ftp connection need to be established to the FRITZ!Box at 192.168.178.1 and the the following ftp commands need to be run: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote SETENV linux_fs_start 0 ftp> quote MEDIA FLSH ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-kernel.bin mtd1 ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-filesystem.bin mtd0 Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
Diffstat (limited to 'target/linux/lantiq/base-files')
-rwxr-xr-xtarget/linux/lantiq/base-files/etc/board.d/01_leds4
-rwxr-xr-xtarget/linux/lantiq/base-files/etc/board.d/02_network9
-rw-r--r--target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom24
-rwxr-xr-xtarget/linux/lantiq/base-files/lib/upgrade/platform.sh8
4 files changed, 40 insertions, 5 deletions
diff --git a/target/linux/lantiq/base-files/etc/board.d/01_leds b/target/linux/lantiq/base-files/etc/board.d/01_leds
index 0426fb18e6..4476a7eb43 100755
--- a/target/linux/lantiq/base-files/etc/board.d/01_leds
+++ b/target/linux/lantiq/base-files/etc/board.d/01_leds
@@ -53,6 +53,10 @@ bt,homehub-v5a)
netgear,dm200)
ucidef_set_led_netdev "lan" "lan" "dm200:green:lan" "eth0"
;;
+avm,fritz3370-rev2-hynix|\
+avm,fritz3370-rev2-micron)
+ ucidef_set_led_switch "lan" "LAN" "fritz3370:green:lan" "switch0" "0x17"
+ ;;
avm,fritz7320)
ucidef_set_led_netdev "wifi" "wifi" "fritz7320:green:wlan" "wlan0"
;;
diff --git a/target/linux/lantiq/base-files/etc/board.d/02_network b/target/linux/lantiq/base-files/etc/board.d/02_network
index ca974b071e..9da01d14cc 100755
--- a/target/linux/lantiq/base-files/etc/board.d/02_network
+++ b/target/linux/lantiq/base-files/etc/board.d/02_network
@@ -135,10 +135,13 @@ lantiq,easy80920-nand|lantiq,easy80920-nor)
"0:lan:4" "1:lan:3" "2:lan:2" "4:lan:1" "5:wan:5" "6t@eth0"
;;
-avm,fritz3370)
+avm,fritz3370-rev2-hynix|\
+avm,fritz3370-rev2-micron)
annex="b"
- wan_mac=$(macaddr_add "$(mtd_get_mac_binary urlader 2439)" 1)
- ucidef_set_interface_lan 'eth0'
+ lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
+ wan_mac=$(macaddr_add "$lan_mac" 3)
+ ucidef_add_switch "switch0" \
+ "0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "6t@eth0"
;;
avm,fritz7320)
diff --git a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
index 498a509012..75b763076e 100644
--- a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
+++ b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
@@ -47,6 +47,24 @@ ath9k_eeprom_extract_raw() {
ath9k_eeprom_die "failed to extract from $mtd"
}
+ath9k_eeprom_extract_reverse() {
+ local part=$1
+ local offset=$2
+ local count=$3
+ local mtd
+ local reversed
+ local caldata
+
+ mtd=$(find_mtd_chardev "$part")
+ reversed=$(hexdump -v -s $offset -n $count -e '/1 "%02x "' $mtd)
+
+ for byte in $reversed; do
+ caldata="\x${byte}${caldata}"
+ done
+
+ printf "%b" "$caldata" > /lib/firmware/$FIRMWARE
+}
+
ath9k_eeprom_extract() {
local part=$1
local offset=$2
@@ -138,7 +156,11 @@ case "$FIRMWARE" in
ath9k_eeprom_extract "calibration" 61440 0
ath9k_patch_fw_mac_crc $(macaddr_add $(mtd_get_mac_ascii uboot-env ethaddr) +2) 524
;;
- avm,fritz3370|avm,fritz7320|avm,fritz7360sl)
+ avm,fritz3370-rev2-hynix|\
+ avm,fritz3370-rev2-micron)
+ ath9k_eeprom_extract_reverse "urlader" 5441 1088
+ ;;
+ avm,fritz7320|avm,fritz7360sl)
ath9k_eeprom_extract "urlader" 2437 0
;;
tplink,tdw8970|tplink,tdw8980)
diff --git a/target/linux/lantiq/base-files/lib/upgrade/platform.sh b/target/linux/lantiq/base-files/lib/upgrade/platform.sh
index 2e58cb799a..ecbb939e36 100755
--- a/target/linux/lantiq/base-files/lib/upgrade/platform.sh
+++ b/target/linux/lantiq/base-files/lib/upgrade/platform.sh
@@ -9,7 +9,13 @@ platform_do_upgrade() {
local board=$(board_name)
case "$board" in
- bt,homehub-v2b|bt,homehub-v3a|bt,homehub-v5a|zyxel,p-2812hnu-f1|zyxel,p-2812hnu-f3)
+ avm,fritz3370-rev2-hynix|\
+ avm,fritz3370-rev2-micron|\
+ bt,homehub-v2b|\
+ bt,homehub-v3a|\
+ bt,homehub-v5a|\
+ zyxel,p-2812hnu-f1|\
+ zyxel,p-2812hnu-f3)
nand_do_upgrade $1
;;
*)