diff options
| author | Paul Wassi <p.wassi@gmx.at> | 2017-03-10 19:10:29 +0100 |
|---|---|---|
| committer | Mathias Kresin <dev@kresin.me> | 2017-07-04 16:29:07 +0200 |
| commit | 9808b9ae0248f0e2b525493f10752b2b9fc9fde4 (patch) | |
| tree | 49c36ed203fd79d89e06a5e1cf833e469d2a236c /target/linux/kirkwood | |
| parent | 08c499f865a1a42ed50e70c8ff68b9916a5033f1 (diff) | |
| download | upstream-9808b9ae0248f0e2b525493f10752b2b9fc9fde4.tar.gz upstream-9808b9ae0248f0e2b525493f10752b2b9fc9fde4.tar.bz2 upstream-9808b9ae0248f0e2b525493f10752b2b9fc9fde4.zip | |
kirkwood: switch to kernel 4.9
Add patches-4.9, some of them (heavily) rewritten:
- ea4500 is upstream available, keep only LEDE changes in dts
- ea3500 is changed to match the structure of the upstream ea4500 dts
- nsa310s rewritten to include the common dtsi
- nsa325 is dropped, since already upstream
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[refresh kernel config, add on100, use the switchdev based mv88e6171
driver for the linksys boards, keep lede specific rootfs/kernel
partition names for linksys boards, reorder patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Diffstat (limited to 'target/linux/kirkwood')
17 files changed, 1647 insertions, 3 deletions
diff --git a/target/linux/kirkwood/Makefile b/target/linux/kirkwood/Makefile index 8c8c272f98..d5df854433 100644 --- a/target/linux/kirkwood/Makefile +++ b/target/linux/kirkwood/Makefile @@ -13,7 +13,7 @@ FEATURES:=usb nand squashfs ramdisk CPU_TYPE:=xscale MAINTAINER:=Luka Perkov <luka@openwrt.org> -KERNEL_PATCHVER:=4.4 +KERNEL_PATCHVER:=4.9 include $(INCLUDE_DIR)/target.mk diff --git a/target/linux/kirkwood/base-files/lib/kirkwood.sh b/target/linux/kirkwood/base-files/lib/kirkwood.sh index dbf3456172..c29a315f79 100755 --- a/target/linux/kirkwood/base-files/lib/kirkwood.sh +++ b/target/linux/kirkwood/base-files/lib/kirkwood.sh @@ -41,11 +41,11 @@ kirkwood_board_detect() { name="pogo_e02" ;; - "Linksys EA3500") + "Linksys Audi (EA3500)") name="linksys-audi" ;; - "Linksys E4200v2 / EA4500") + "Linksys Viper (E4200v2 / EA4500)") name="linksys-viper" ;; diff --git a/target/linux/kirkwood/config-4.9 b/target/linux/kirkwood/config-4.9 new file mode 100644 index 0000000000..86d999edb1 --- /dev/null +++ b/target/linux/kirkwood/config-4.9 @@ -0,0 +1,333 @@ +CONFIG_ALIGNMENT_TRAP=y +CONFIG_ARCH_CLOCKSOURCE_DATA=y +CONFIG_ARCH_HAS_ELF_RANDOMIZE=y +CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y +CONFIG_ARCH_HAS_SG_CHAIN=y +CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y +CONFIG_ARCH_MULTIPLATFORM=y +CONFIG_ARCH_MULTI_CPU_AUTO=y +# CONFIG_ARCH_MULTI_V4 is not set +# CONFIG_ARCH_MULTI_V4T is not set +CONFIG_ARCH_MULTI_V4_V5=y +CONFIG_ARCH_MULTI_V5=y +CONFIG_ARCH_MVEBU=y +CONFIG_ARCH_NR_GPIO=0 +# CONFIG_ARCH_OXNAS is not set +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y +CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y +CONFIG_ARCH_SUPPORTS_UPROBES=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARCH_USE_BUILTIN_BSWAP=y +CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y +CONFIG_ARCH_WANT_GENERAL_HUGETLB=y +CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y +CONFIG_ARCH_WANT_LIBATA_LEDS=y +CONFIG_ARM=y +# CONFIG_ARMADA_THERMAL is not set +CONFIG_ARM_APPENDED_DTB=y +CONFIG_ARM_ATAG_DTB_COMPAT=y +# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is not set +CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y +# CONFIG_ARM_CPU_SUSPEND is not set +CONFIG_ARM_HAS_SG_CHAIN=y +# CONFIG_ARM_KIRKWOOD_CPUIDLE is not set +CONFIG_ARM_L1_CACHE_SHIFT=5 +# CONFIG_ARM_MVEBU_V7_CPUIDLE is not set +CONFIG_ARM_PATCH_PHYS_VIRT=y +# CONFIG_ARM_THUMB is not set +CONFIG_ATA=y +CONFIG_ATAGS=y +CONFIG_ATA_LEDS=y +CONFIG_AUTO_ZRELADDR=y +# CONFIG_BINFMT_FLAT is not set +CONFIG_BLK_DEV_SD=y +CONFIG_BLK_MQ_PCI=y +CONFIG_CACHE_FEROCEON_L2=y +# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set +# CONFIG_CACHE_L2X0 is not set +CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLKSRC_MMIO=y +CONFIG_CLKSRC_OF=y +CONFIG_CLKSRC_PROBE=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_COMMON_CLK=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5T=y +# CONFIG_CPU_BIG_ENDIAN is not set +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_FEROCEON=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y +CONFIG_CPU_FEROCEON=y +# CONFIG_CPU_FEROCEON_OLD_ID is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +CONFIG_CPU_IDLE=y +CONFIG_CPU_IDLE_GOV_LADDER=y +CONFIG_CPU_PABRT_LEGACY=y +CONFIG_CPU_PM=y +CONFIG_CPU_TLB_FEROCEON=y +CONFIG_CPU_USE_DOMAINS=y +CONFIG_CRC16=y +# CONFIG_CRC32_SARWATE is not set +CONFIG_CRC32_SLICEBY8=y +CONFIG_CRYPTO_CRC32C=y +CONFIG_CRYPTO_DEFLATE=y +CONFIG_CRYPTO_DES=y +CONFIG_CRYPTO_DEV_MARVELL_CESA=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_HW=y +CONFIG_CRYPTO_LZO=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_WORKQUEUE=y +CONFIG_DEBUG_LL=y +CONFIG_DEBUG_LL_INCLUDE="debug/8250.S" +CONFIG_DEBUG_MVEBU_UART0_ALTERNATE=y +# CONFIG_DEBUG_MVEBU_UART1_ALTERNATE is not set +CONFIG_DEBUG_UART_8250=y +# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set +CONFIG_DEBUG_UART_8250_SHIFT=2 +# CONFIG_DEBUG_UART_8250_WORD is not set +CONFIG_DEBUG_UART_PHYS=0xf1012000 +CONFIG_DEBUG_UART_VIRT=0xfed12000 +CONFIG_DEBUG_UNCOMPRESS=y +# CONFIG_DEBUG_USER is not set +# CONFIG_DLCI is not set +CONFIG_DNOTIFY=y +CONFIG_DTC=y +# CONFIG_EARLY_PRINTK is not set +CONFIG_EDAC_ATOMIC_SCRUB=y +CONFIG_EDAC_SUPPORT=y +CONFIG_EXT4_FS=y +CONFIG_FIXED_PHY=y +CONFIG_FIX_EARLYCON_MEM=y +CONFIG_FRAME_POINTER=y +CONFIG_FS_MBCACHE=y +CONFIG_GENERIC_ALLOCATOR=y +CONFIG_GENERIC_ATOMIC64=y +CONFIG_GENERIC_BUG=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_EARLY_IOREMAP=y +CONFIG_GENERIC_IDLE_POLL_SETUP=y +CONFIG_GENERIC_IO=y +CONFIG_GENERIC_IRQ_CHIP=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_IRQ_SHOW_LEVEL=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_PHY=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_STRNCPY_FROM_USER=y +CONFIG_GENERIC_STRNLEN_USER=y +CONFIG_GLOB=y +CONFIG_GPIOLIB=y +CONFIG_GPIO_MVEBU=y +CONFIG_GPIO_SYSFS=y +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set +CONFIG_HAVE_ARCH_AUDITSYSCALL=y +# CONFIG_HAVE_ARCH_BITREVERSE is not set +CONFIG_HAVE_ARCH_JUMP_LABEL=y +CONFIG_HAVE_ARCH_KGDB=y +CONFIG_HAVE_ARCH_PFN_VALID=y +CONFIG_HAVE_ARCH_SECCOMP_FILTER=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set +CONFIG_HAVE_CBPF_JIT=y +CONFIG_HAVE_CC_STACKPROTECTOR=y +CONFIG_HAVE_CLK=y +CONFIG_HAVE_CLK_PREPARE=y +CONFIG_HAVE_CONTEXT_TRACKING=y +CONFIG_HAVE_C_RECORDMCOUNT=y +CONFIG_HAVE_DEBUG_KMEMLEAK=y +CONFIG_HAVE_DMA_API_DEBUG=y +CONFIG_HAVE_DMA_CONTIGUOUS=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y +CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_HAVE_IDE=y +CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y +CONFIG_HAVE_MEMBLOCK=y +CONFIG_HAVE_MOD_ARCH_SPECIFIC=y +CONFIG_HAVE_NET_DSA=y +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_OPTPROBES=y +CONFIG_HAVE_PERF_EVENTS=y +CONFIG_HAVE_PERF_REGS=y +CONFIG_HAVE_PERF_USER_STACK_DUMP=y +CONFIG_HAVE_PROC_CPU=y +CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y +CONFIG_HAVE_SYSCALL_TRACEPOINTS=y +CONFIG_HAVE_UID16=y +CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y +CONFIG_HW_RANDOM=y +CONFIG_HZ_FIXED=0 +CONFIG_HZ_PERIODIC=y +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_MV64XXX=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_IOMMU_HELPER=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_WORK=y +CONFIG_JBD2=y +CONFIG_KIRKWOOD_CLK=y +CONFIG_KIRKWOOD_THERMAL=y +CONFIG_LEDS_GPIO=y +CONFIG_LEDS_NETXBIG=y +CONFIG_LEDS_NS2=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +CONFIG_LIBFDT=y +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y +CONFIG_MACH_KIRKWOOD=y +CONFIG_MACH_MVEBU_ANY=y +CONFIG_MANGLE_BOOTARGS=y +CONFIG_MDIO_BOARDINFO=y +# CONFIG_MFD_MAX77620 is not set +CONFIG_MIGHT_HAVE_PCI=y +CONFIG_MMC=y +CONFIG_MMC_BLOCK=y +CONFIG_MMC_MVSDIO=y +# CONFIG_MMC_TIFM_SD is not set +CONFIG_MODULES_USE_ELF_REL=y +# CONFIG_MTD_CFI is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_ECC=y +CONFIG_MTD_NAND_ORION=y +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_BEB_LIMIT=20 +CONFIG_MTD_UBI_BLOCK=y +# CONFIG_MTD_UBI_FASTMAP is not set +# CONFIG_MTD_UBI_GLUEBI is not set +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_MULTI_IRQ_HANDLER=y +CONFIG_MV643XX_ETH=y +CONFIG_MVEBU_CLK_COMMON=y +CONFIG_MVEBU_MBUS=y +CONFIG_MVMDIO=y +# CONFIG_MVNETA is not set +CONFIG_MVSW61XX_PHY=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEED_KUSER_HELPERS=y +CONFIG_NEED_PER_CPU_KM=y +CONFIG_NLS=y +CONFIG_NO_BOOTMEM=y +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_ADDRESS_PCI=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_MDIO=y +CONFIG_OF_NET=y +CONFIG_OF_PCI=y +CONFIG_OF_PCI_IRQ=y +CONFIG_OF_RESERVED_MEM=y +CONFIG_OLD_SIGACTION=y +CONFIG_OLD_SIGSUSPEND3=y +CONFIG_ORION_IRQCHIP=y +CONFIG_ORION_TIMER=y +CONFIG_ORION_WATCHDOG=y +CONFIG_OUTER_CACHE=y +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_DOMAINS_GENERIC=y +CONFIG_PCI_MVEBU=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PGTABLE_LEVELS=2 +CONFIG_PHYLIB=y +CONFIG_PHY_MVEBU_SATA=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_KIRKWOOD=y +CONFIG_PINCTRL_MVEBU=y +# CONFIG_PINCTRL_SINGLE is not set +CONFIG_PLAT_ORION=y +CONFIG_POWER_RESET=y +# CONFIG_POWER_RESET_BRCMKONA is not set +CONFIG_POWER_RESET_GPIO=y +# CONFIG_POWER_RESET_QNAP is not set +CONFIG_POWER_SUPPLY=y +CONFIG_RATIONAL=y +# CONFIG_RCU_STALL_COMMON is not set +CONFIG_REGMAP=y +CONFIG_REGMAP_I2C=y +CONFIG_REGMAP_SPI=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_MV=y +CONFIG_RTC_I2C_AND_SPI=y +CONFIG_RTC_MC146818_LIB=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_SATA_MV=y +# CONFIG_SCHED_INFO is not set +CONFIG_SCSI=y +CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y +CONFIG_SERIAL_8250_FSL=y +# CONFIG_SERIAL_MVEBU_UART is not set +CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_SG_POOL=y +CONFIG_SOC_BUS=y +CONFIG_SPARSE_IRQ=y +CONFIG_SPI=y +CONFIG_SPI_MASTER=y +CONFIG_SPI_ORION=y +CONFIG_SPLIT_PTLOCK_CPUS=999999 +CONFIG_SRAM=y +CONFIG_SRCU=y +CONFIG_SWCONFIG=y +CONFIG_SWIOTLB=y +CONFIG_SWPHY=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_THERMAL=y +CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y +CONFIG_THERMAL_GOV_STEP_WISE=y +CONFIG_THERMAL_OF=y +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_UBIFS_FS=y +CONFIG_UBIFS_FS_ADVANCED_COMPR=y +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_ZLIB=y +CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h" +CONFIG_USB=y +CONFIG_USB_COMMON=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_HCD_ORION=y +# CONFIG_USB_EHCI_HCD_PLATFORM is not set +CONFIG_USB_EHCI_PCI=y +CONFIG_USB_LED_TRIG=y +CONFIG_USB_STORAGE=y +CONFIG_USB_SUPPORT=y +# CONFIG_USB_UHCI_HCD is not set +CONFIG_USE_OF=y +CONFIG_VECTORS_BASE=0xffff0000 +# CONFIG_VFP is not set +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_WAN=y +CONFIG_WATCHDOG_CORE=y +CONFIG_XZ_DEC_ARM=y +CONFIG_XZ_DEC_BCJ=y +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZLIB_DEFLATE=y +CONFIG_ZLIB_INFLATE=y diff --git a/target/linux/kirkwood/patches-4.9/100-ib62x0.patch b/target/linux/kirkwood/patches-4.9/100-ib62x0.patch new file mode 100644 index 0000000000..d6d10d8144 --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/100-ib62x0.patch @@ -0,0 +1,21 @@ +--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts ++++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts +@@ -117,13 +117,13 @@ + }; + + partition@100000 { +- label = "uImage"; +- reg = <0x0100000 0x600000>; ++ label = "second stage u-boot"; ++ reg = <0x100000 0x200000>; + }; + +- partition@700000 { +- label = "root"; +- reg = <0x0700000 0xf900000>; ++ partition@200000 { ++ label = "ubi"; ++ reg = <0x200000 0xfe00000>; + }; + + }; diff --git a/target/linux/kirkwood/patches-4.9/101-iconnect.patch b/target/linux/kirkwood/patches-4.9/101-iconnect.patch new file mode 100644 index 0000000000..20fb0c8c57 --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/101-iconnect.patch @@ -0,0 +1,41 @@ +--- a/arch/arm/boot/dts/kirkwood-iconnect.dts ++++ b/arch/arm/boot/dts/kirkwood-iconnect.dts +@@ -145,28 +145,23 @@ + status = "okay"; + + partition@0 { +- label = "uboot"; +- reg = <0x0000000 0xc0000>; ++ label = "u-boot"; ++ reg = <0x0000000 0xe0000>; + }; + +- partition@a0000 { +- label = "env"; +- reg = <0xa0000 0x20000>; ++ partition@e0000 { ++ label = "u-boot environment"; ++ reg = <0xe0000 0x100000>; + }; + + partition@100000 { +- label = "zImage"; +- reg = <0x100000 0x300000>; ++ label = "second stage u-boot"; ++ reg = <0x100000 0x200000>; + }; + +- partition@540000 { +- label = "initrd"; +- reg = <0x540000 0x300000>; +- }; +- +- partition@980000 { +- label = "boot"; +- reg = <0x980000 0x1f400000>; ++ partition@200000 { ++ label = "ubi"; ++ reg = <0x200000 0x1fe00000>; + }; + }; + diff --git a/target/linux/kirkwood/patches-4.9/102-dockstar.patch b/target/linux/kirkwood/patches-4.9/102-dockstar.patch new file mode 100644 index 0000000000..f66e19d27f --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/102-dockstar.patch @@ -0,0 +1,32 @@ +--- a/arch/arm/boot/dts/kirkwood-dockstar.dts ++++ b/arch/arm/boot/dts/kirkwood-dockstar.dts +@@ -77,18 +77,22 @@ + + partition@0 { + label = "u-boot"; +- reg = <0x0000000 0x100000>; +- read-only; ++ reg = <0x0000000 0xe0000>; ++ }; ++ ++ partition@e0000 { ++ label = "u-boot environment"; ++ reg = <0xe0000 0x100000>; + }; + + partition@100000 { +- label = "uImage"; +- reg = <0x0100000 0x400000>; ++ label = "second stage u-boot"; ++ reg = <0x100000 0x200000>; + }; + +- partition@500000 { +- label = "data"; +- reg = <0x0500000 0xfb00000>; ++ partition@200000 { ++ label = "ubi"; ++ reg = <0x200000 0xfe00000>; + }; + }; + diff --git a/target/linux/kirkwood/patches-4.9/104-ea3500.patch b/target/linux/kirkwood/patches-4.9/104-ea3500.patch new file mode 100644 index 0000000000..3659f879b9 --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/104-ea3500.patch @@ -0,0 +1,258 @@ +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -220,6 +220,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ + kirkwood-linkstation-lswsxl.dtb \ + kirkwood-linkstation-lswvl.dtb \ + kirkwood-linkstation-lswxl.dtb \ ++ kirkwood-linksys-audi.dtb \ + kirkwood-linksys-viper.dtb \ + kirkwood-lschlv2.dtb \ + kirkwood-lsxhl.dtb \ +--- /dev/null ++++ b/arch/arm/boot/dts/kirkwood-linksys-audi.dts +@@ -0,0 +1,245 @@ ++/* ++ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500 ++ * ++ * (c) 2013 Jonas Gorski <jogo@openwrt.org> ++ * (c) 2013 Deutsche Telekom Innovation Laboratories ++ * (c) 2014 Luka Perkov <luka@openwrt.org> ++ * (c) 2014 Dan Walters <dan@walters.io> ++ * ++ * This file is licensed under the terms of the GNU General Public ++ * License version 2. This program is licensed "as is" without any ++ * warranty of any kind, whether express or implied. ++ */ ++ ++/dts-v1/; ++ ++#include "kirkwood.dtsi" ++#include "kirkwood-6282.dtsi" ++ ++/ { ++ model = "Linksys Audi (EA3500)"; ++ compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood"; ++ ++ memory { ++ device_type = "memory"; ++ reg = <0x00000000 0x4000000>; ++ }; ++ ++ aliases { ++ serial0 = &uart0; ++ }; ++ ++ chosen { ++ stdout-path = "serial0:115200n8"; ++ }; ++ ++ gpio_keys { ++ compatible = "gpio-keys"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >; ++ pinctrl-names = "default"; ++ ++ wps { ++ label = "WPS Button"; ++ linux,code = <KEY_WPS_BUTTON>; ++ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; ++ }; ++ ++ reset { ++ label = "Reset Button"; ++ linux,code = <KEY_RESTART>; ++ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ gpio-leds { ++ compatible = "gpio-leds"; ++ pinctrl-0 = < &pmx_led_green_power >; ++ pinctrl-names = "default"; ++ ++ green-power { ++ label = "audi:green:power"; ++ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ ++ mvsw61xx { ++ compatible = "marvell,88e6171"; ++ status = "okay"; ++ reg = <0x10>; ++ ++ mii-bus = <&mdio>; ++ cpu-port-0 = <5>; ++ cpu-port-1 = <6>; ++ is-indirect; ++ }; ++ ++ dsa { ++ compatible = "marvell,dsa"; ++ #address-cells = <2>; ++ #size-cells = <0>; ++ ++ dsa,ethernet = <ð0port>; ++ dsa,mii-bus = <&mdio>; ++ ++ switch@16,0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <16 0>; /* MDIO address 16, switch 0 in tree */ ++ ++ port@0 { ++ reg = <0>; ++ label = "ethernet1"; ++ }; ++ ++ port@1 { ++ reg = <1>; ++ label = "ethernet2"; ++ }; ++ ++ port@2 { ++ reg = <2>; ++ label = "ethernet3"; ++ }; ++ ++ port@3 { ++ reg = <3>; ++ label = "ethernet4"; ++ }; ++ ++ port@4 { ++ reg = <4>; ++ label = "internet"; ++ }; ++ ++ port@5 { ++ reg = <5>; ++ label = "cpu"; ++ }; ++ }; ++ }; ++}; ++ ++&pinctrl { ++ pmx_led_green_power: pmx-led-green-power { ++ marvell,pins = "mpp7"; ++ marvell,function = "gpo"; ++ }; ++ pmx_btn_wps: pmx-btn-wps { ++ marvell,pins = "mpp47"; ++ marvell,function = "gpio"; ++ }; ++ pmx_btn_reset: pmx-btn-reset { ++ marvell,pins = "mpp48"; ++ marvell,function = "gpio"; ++ }; ++}; ++ ++&nand { ++ status = "okay"; ++ pinctrl-0 = <&pmx_nand>; ++ pinctrl-names = "default"; ++ ++ partitions { ++ compatible = "fixed-partitions"; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ partition@0 { ++ label = "u-boot"; ++ reg = <0x0 0x80000>; ++ read-only; ++ }; ++ ++ partition@80000 { ++ label = "u_env"; ++ reg = <0x80000 0x4000>; ++ }; ++ ++ partition@84000 { ++ label = "s_env"; ++ reg = <0x84000 0x4000>; ++ }; ++ ++ partition@200000 { ++ label = "kernel1"; ++ reg = <0x200000 0x290000>; ++ }; ++ ++ partition@490000 { ++ label = "rootfs1"; ++ reg = <0x490000 0x1170000>; ++ }; ++ ++ partition@1600000 { ++ label = "kernel2"; ++ reg = <0x1600000 0x290000>; ++ }; ++ ++ partition@1890000 { ++ label = "rootfs2"; ++ reg = <0x1890000 0x1170000>; ++ }; ++ ++ partition@2a00000 { ++ label = "syscfg"; ++ reg = <0x2a00000 0x1600000>; ++ }; ++ ++ partition@88000 { ++ label = "unused"; ++ reg = <0x88000 0x178000>; ++ }; ++ ++ }; ++}; ++ ++&pciec { ++ status = "okay"; ++}; ++ ++&pcie0 { ++ status = "okay"; ++}; ++ ++&pcie1 { ++ status = "okay"; ++}; ++ ++&mdio { ++ status = "okay"; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set ++ * fixed speed and duplex. ++ */ ++ð0 { ++ status = "okay"; ++ ethernet0-port@0 { ++ speed = <1000>; ++ duplex = <1>; ++ }; ++}; ++ ++/* eth1 is connected to the switch at port 6. However DSA only supports a ++ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion. ++ */ ++ð1 { ++ status = "okay"; ++ ethernet1-port@0 { ++ speed = <1000>; ++ duplex = <1>; ++ }; ++}; ++ ++/* There is no battery on the board, so the RTC does not keep ++ * time when there is no power, making it useless. ++ */ ++&rtc { ++ status = "disabled"; ++}; diff --git a/target/linux/kirkwood/patches-4.9/105-ea4500.patch b/target/linux/kirkwood/patches-4.9/105-ea4500.patch new file mode 100644 index 0000000000..d76cdace51 --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/105-ea4500.patch @@ -0,0 +1,64 @@ +--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts ++++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts +@@ -69,6 +69,17 @@ + }; + }; + ++ mvsw61xx { ++ compatible = "marvell,88e6171"; ++ status = "okay"; ++ reg = <0x10>; ++ ++ mii-bus = <&mdio>; ++ cpu-port-0 = <5>; ++ cpu-port-1 = <6>; ++ is-indirect; ++ }; ++ + dsa { + compatible = "marvell,dsa"; + #address-cells = <2>; +@@ -161,22 +172,22 @@ + }; + + partition@200000 { +- label = "kernel"; ++ label = "kernel1"; + reg = <0x200000 0x2A0000>; + }; + + partition@4A0000 { +- label = "rootfs"; ++ label = "rootfs1"; + reg = <0x4A0000 0x1760000>; + }; + + partition@1C00000 { +- label = "alt_kernel"; ++ label = "kernel2"; + reg = <0x1C00000 0x2A0000>; + }; + + partition@1EA0000 { +- label = "alt_rootfs"; ++ label = "rootfs2"; + reg = <0x1EA0000 0x1760000>; + }; + +@@ -225,10 +236,14 @@ + }; + + /* eth1 is connected to the switch at port 6. However DSA only supports a +- * single CPU port. So leave this port disabled to avoid confusion. ++ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion. + */ + ð1 { +- status = "disabled"; ++ status = "okay"; ++ ethernet1-port@0 { ++ speed = <1000>; ++ duplex = <1>; ++ }; + }; + + /* There is no battery on the board, so the RTC does not keep diff --git a/target/linux/kirkwood/patches-4.9/105-goflexhome.patch b/target/linux/kirkwood/patches-4.9/105-goflexhome.patch new file mode 100644 index 0000000000..0962249664 --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/105-goflexhome.patch @@ -0,0 +1,130 @@ +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -207,6 +207,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ + kirkwood-ds411.dtb \ + kirkwood-ds411j.dtb \ + kirkwood-ds411slim.dtb \ ++ kirkwood-goflexhome.dtb \ + kirkwood-goflexnet.dtb \ + kirkwood-guruplug-server-plus.dtb \ + kirkwood-ib62x0.dtb \ +--- /dev/null ++++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts +@@ -0,0 +1,117 @@ ++/dts-v1/; ++ ++#include "kirkwood.dtsi" ++#include "kirkwood-6281.dtsi" ++ ++/ { ++ model = "Seagate GoFlex Home"; ++ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood"; ++ ++ memory { ++ device_type = "memory"; ++ reg = <0x00000000 0x8000000>; ++ }; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; ++ stdout-path = &uart0; ++ }; ++ ++ ocp@f1000000 { ++ pinctrl: pin-controller@10000 { ++ pmx_usb_power_enable: pmx-usb-power-enable { ++ marvell,pins = "mpp29"; ++ marvell,function = "gpio"; ++ }; ++ pmx_led_white: pmx-led-white { ++ marvell,pins = "mpp40"; ++ marvell,function = "gpio"; ++ }; ++ pmx_led_green: pmx-led_green { ++ marvell,pins = "mpp46"; ++ marvell,function = "gpio"; ++ }; ++ pmx_led_orange: pmx-led-orange { ++ marvell,pins = "mpp47"; ++ marvell,function = "gpio"; ++ }; ++ }; ++ serial@12000 { ++ status = "ok"; ++ }; ++ ++ sata@80000 { ++ status = "okay"; ++ nr-ports = <2>; ++ }; ++ ++ }; ++ gpio-leds { ++ compatible = "gpio-leds"; ++ ++ health { ++ label = "status:green:health"; ++ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "default-on"; ++ }; ++ fault { ++ label = "status:orange:fault"; ++ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; ++ }; ++ misc { ++ label = "status:white:misc"; ++ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "disk-activity"; ++ }; ++ }; ++ regulators { ++ compatible = "simple-bus"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-0 = <&pmx_usb_power_enable>; ++ pinctrl-names = "default"; ++ ++ usb_power: regulator@1 { ++ compatible = "regulator-fixed"; ++ reg = <1>; ++ regulator-name = "USB Power"; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ enable-active-high; ++ regulator-always-on; ++ regulator-boot-on; ++ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++}; ++ ++&nand { ++ chip-delay = <40>; ++ status = "okay"; ++ ++ partition@0 { ++ label = "u-boot"; ++ reg = <0x0000000 0x100000>; ++ read-only; ++ }; ++ ++ partition@100000 { ++ label = "ubi"; ++ reg = <0x100000 0x0ff00000>; ++ }; ++}; ++ ++&mdio { ++ status = "okay"; ++ ++ ethphy0: ethernet-phy@0 { ++ reg = <0>; ++ }; ++}; ++ ++ð0 { ++ status = "okay"; ++ ethernet0-port@0 { ++ phy-handle = <ðphy0>; ++ }; ++}; diff --git a/target/linux/kirkwood/patches-4.9/106-goflexnet.patch b/target/linux/kirkwood/patches-4.9/106-goflexnet.patch new file mode 100644 index 0000000000..9b0620b818 --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/106-goflexnet.patch @@ -0,0 +1,23 @@ +--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts ++++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts +@@ -158,18 +158,8 @@ + }; + + partition@100000 { +- label = "uImage"; +- reg = <0x0100000 0x400000>; +- }; +- +- partition@500000 { +- label = "pogoplug"; +- reg = <0x0500000 0x2000000>; +- }; +- +- partition@2500000 { +- label = "root"; +- reg = <0x02500000 0xd800000>; ++ label = "ubi"; ++ reg = <0x0100000 0x0ff00000>; + }; + }; + diff --git a/target/linux/kirkwood/patches-4.9/107-01-zyxel-nsa3x0-common-nand-partitions.patch b/target/linux/kirkwood/patches-4.9/107-01-zyxel-nsa3x0-common-nand-partitions.patch new file mode 100644 index 0000000000..a358e3962e --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/107-01-zyxel-nsa3x0-common-nand-partitions.patch @@ -0,0 +1,48 @@ +--- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi ++++ b/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi +@@ -111,40 +111,16 @@ + + partition@0 { + label = "uboot"; +- reg = <0x0000000 0x0100000>; ++ reg = <0x0000000 0x00c0000>; + read-only; + }; + partition@100000 { + label = "uboot_env"; +- reg = <0x0100000 0x0080000>; ++ reg = <0x00c0000 0x0080000>; + }; +- partition@180000 { +- label = "key_store"; +- reg = <0x0180000 0x0080000>; +- }; +- partition@200000 { +- label = "info"; +- reg = <0x0200000 0x0080000>; +- }; +- partition@280000 { +- label = "etc"; +- reg = <0x0280000 0x0a00000>; +- }; +- partition@c80000 { +- label = "kernel_1"; +- reg = <0x0c80000 0x0a00000>; +- }; +- partition@1680000 { +- label = "rootfs1"; +- reg = <0x1680000 0x2fc0000>; +- }; +- partition@4640000 { +- label = "kernel_2"; +- reg = <0x4640000 0x0a00000>; +- }; +- partition@5040000 { +- label = "rootfs2"; +- reg = <0x5040000 0x2fc0000>; ++ partition@140000 { ++ label = "ubi"; ++ reg = <0x0140000 0x7ec0000>; + }; + }; + diff --git a/target/linux/kirkwood/patches-4.9/107-02-nsa310b.patch b/target/linux/kirkwood/patches-4.9/107-02-nsa310b.patch new file mode 100644 index 0000000000..7110222936 --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/107-02-nsa310b.patch @@ -0,0 +1,147 @@ +kirkwood: add nsa310b dtb, a zyxel nsa310 variant + +add support to a nsa310 variant with red/green usb led +and lm85 temp/fan controller + +Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it> + +NOTE: this patch can be upstreamed as-is, LEDE-specific + nand partitions are set in another patch + +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -238,6 +238,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ + kirkwood-ns2mini.dtb \ + kirkwood-nsa310.dtb \ + kirkwood-nsa310a.dtb \ ++ kirkwood-nsa310b.dtb \ + kirkwood-nsa320.dtb \ + kirkwood-nsa325.dtb \ + kirkwood-openblocks_a6.dtb \ +--- /dev/null ++++ b/arch/arm/boot/dts/kirkwood-nsa310b.dts +@@ -0,0 +1,124 @@ ++/dts-v1/; ++ ++#include "kirkwood-nsa3x0-common.dtsi" ++ ++/* ++ * There are at least two different NSA310 designs. This variant has ++ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller. ++ */ ++ ++/ { ++ model = "ZyXEL NSA310b"; ++ compatible = "zyxel,nsa310a", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood"; ++ ++ memory { ++ device_type = "memory"; ++ reg = <0x00000000 0x10000000>; ++ }; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200"; ++ stdout-path = &uart0; ++ }; ++ ++ ocp@f1000000 { ++ pinctrl: pin-controller@10000 { ++ pinctrl-names = "default"; ++ ++ pmx_led_esata_green: pmx-led-esata-green { ++ marvell,pins = "mpp12"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_esata_red: pmx-led-esata-red { ++ marvell,pins = "mpp13"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_usb_green: pmx-led-usb-green { ++ marvell,pins = "mpp15"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_usb_red: pmx-led-usb-red { ++ marvell,pins = "mpp16"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_sys_green: pmx-led-sys-green { ++ marvell,pins = "mpp28"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_sys_red: pmx-led-sys-red { ++ marvell,pins = "mpp29"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_hdd_green: pmx-led-hdd-green { ++ marvell,pins = "mpp41"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_hdd_red: pmx-led-hdd-red { ++ marvell,pins = "mpp42"; ++ marvell,function = "gpio"; ++ }; ++ ++ }; ++ ++ i2c@11000 { ++ status = "okay"; ++ ++ lm85: lm85@2e { ++ compatible = "national,lm85"; ++ reg = <0x2e>; ++ }; ++ }; ++ }; ++ ++ gpio-leds { ++ compatible = "gpio-leds"; ++ ++ green-sys { ++ label = "nsa310:green:sys"; ++ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; ++ }; ++ red-sys { ++ label = "nsa310:red:sys"; ++ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; ++ }; ++ green-hdd { ++ label = "nsa310:green:hdd"; ++ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; ++ }; ++ red-hdd { ++ label = "nsa310:red:hdd"; ++ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; ++ }; ++ green-esata { ++ label = "nsa310:green:esata"; ++ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; ++ }; ++ red-esata { ++ label = "nsa310:red:esata"; ++ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; ++ }; ++ green-usb { ++ label = "nsa310:green:usb"; ++ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; ++ }; ++ red-usb { ++ label = "nsa310:red:usb"; ++ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; ++ }; ++ green-copy { ++ label = "nsa310:green:copy"; ++ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; ++ }; ++ red-copy { ++ label = "nsa310:red:copy"; ++ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++}; diff --git a/target/linux/kirkwood/patches-4.9/107-03-nsa310s.patch b/target/linux/kirkwood/patches-4.9/107-03-nsa310s.patch new file mode 100644 index 0000000000..0e69f0cfa4 --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/107-03-nsa310s.patch @@ -0,0 +1,267 @@ +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -239,6 +239,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ + kirkwood-nsa310.dtb \ + kirkwood-nsa310a.dtb \ + kirkwood-nsa310b.dtb \ ++ kirkwood-nsa310s.dtb \ + kirkwood-nsa320.dtb \ + kirkwood-nsa325.dtb \ + kirkwood-openblocks_a6.dtb \ +--- /dev/null ++++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts +@@ -0,0 +1,254 @@ ++/dts-v1/; ++ ++#include "kirkwood-nsa3x0-common.dtsi" ++ ++/ { ++ model = "ZyXEL NSA310S"; ++ compatible = "zyxel,nsa320s", "marvell,kirkwood-88f6702", "marvell,kirkwood"; ++ ++ memory { ++ device_type = "memory"; ++ reg = <0x00000000 0x10000000>; ++ }; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200n8 earlyprintk"; ++ stdout-path = &uart0; ++ }; ++ ++ ocp@f1000000 { ++ pinctrl: pin-controller@10000 { ++ pinctrl-names = "default"; ++ ++ pmx_sata0: pmx-sata0 { ++ marvell,pins; ++ marvell,function = "sata0"; ++ }; ++ ++ pmx_sata1: pmx-sata1 { ++ marvell,pins; ++ marvell,function = "sata1"; ++ }; ++ ++ pmx_usb_power: pmx-usb-power { ++ marvell,pins = "mpp21"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_pwr_off: pmx-pwr-off { ++ marvell,pins = "mpp27"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_btn_reset: pmx-btn-reset { ++ marvell,pins = "mpp24"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_btn_copy: pmx-btn-copy { ++ marvell,pins = "mpp25"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_btn_power: pmx-btn-power { ++ marvell,pins = "mpp26"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_hdd2_green: pmx-led-hdd2-green { ++ marvell,pins = "mpp34"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_hdd2_red: pmx-led-hdd2-red { ++ marvell,pins = "mpp12"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_usb_green: pmx-led-usb-green { ++ marvell,pins = "mpp15"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_copy_green: pmx-led-copy-green { ++ marvell,pins = "mpp22"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_copy_red: pmx-led-copy-red { ++ marvell,pins = "mpp23"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_sys_green: pmx-led-sys-green { ++ marvell,pins = "mpp28"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_sys_orange: pmx-led-sys-orange { ++ marvell,pins = "mpp29"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_hdd1_green: pmx-led-hdd1-green { ++ marvell,pins = "mpp16"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_hdd1_red: pmx-led-hdd1-red { ++ marvell,pins = "mpp13"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_pwr_sata1: pmx-pwr-sata1 { ++ marvell,pins = "mpp33"; ++ marvell,function = "gpio"; ++ }; ++ ++ }; ++ ++ i2c@11000 { ++ status = "okay"; ++ ++ ht1382: rtc@68 { ++ compatible = "htk,ht1382"; ++ reg = <0x68>; ++ }; ++ }; ++ }; ++ ++ regulators { ++ compatible = "simple-bus"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-0 = <&pmx_pwr_sata1>; ++ pinctrl-names = "default"; ++ ++ usb0_power: regulator@1 { ++ enable-active-high; ++ }; ++ ++ sata1_power: regulator@2 { ++ compatible = "regulator-fixed"; ++ reg = <2>; ++ regulator-name = "SATA1 Power"; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ regulator-always-on; ++ regulator-boot-on; ++ enable-active-high; ++ gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ ++ gpio_keys { ++ power { ++ gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>; ++ }; ++ copy { ++ gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; ++ }; ++ reset { ++ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ gpio-leds { ++ compatible = "gpio-leds"; ++ ++ green-sys { ++ label = "nsa310s:green:sys"; ++ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; ++ }; ++ orange-sys { ++ label = "nsa310s:orange:sys"; ++ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; ++ }; ++ green-hdd1 { ++ label = "nsa310s:green:hdd1"; ++ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; ++ }; ++ red-hdd1 { ++ label = "nsa310s:red:hdd1"; ++ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; ++ }; ++ green-hdd2 { ++ label = "nsa310s:green:hdd2"; ++ gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; ++ }; ++ red-hdd2 { ++ label = "nsa310s:red:hdd2"; ++ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; ++ }; ++ green-usb { ++ label = "nsa310s:green:usb"; ++ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; ++ }; ++ green-copy { ++ label = "nsa310s:green:copy"; ++ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; ++ }; ++ red-copy { ++ label = "nsa310s:red:copy"; ++ gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ ++ gpio_poweroff { ++ gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>; ++ }; ++}; ++ ++&nand { ++ status = "okay"; ++ chip-delay = <35>; ++ ++ partition@0 { ++ label = "uboot"; ++ reg = <0x0000000 0xe0000>; ++ read-only; ++ }; ++ ++ partition@e0000 { ++ label = "uboot_env"; ++ reg = <0xe0000 0x100000>; ++ }; ++ ++ partition@100000 { ++ label = "second stage u-boot"; ++ reg = <0x100000 0x200000>; ++ }; ++ ++ partition@200000 { ++ label = "ubi"; ++ reg = <0x200000 0x7e00000>; ++ }; ++}; ++ ++&sata { ++ status = "okay"; ++ nr-ports = <2>; ++}; ++ ++&mdio { ++ status = "okay"; ++ ethphy0: ethernet-phy@1 { ++ compatible = "marvell,88e1318s"; ++ reg = <1>; ++ marvell,reg-init = <0x1 0x16 0x0 0x3>, ++ <0x1 0x10 0x0 0x1017>, ++ <0x1 0x11 0x0 0x4408>, ++ <0x1 0x16 0x0 0x0>, ++ <0x1 0x4 0x0 0x1e1>, ++ <0x1 0x9 0x0 0x300>, ++ <0x1 0x10 0x0 0x3860>, ++ <0x1 0x0 0x0 0x9140>; ++ }; ++}; ++ ++ð0 { ++ status = "okay"; ++ ethernet0-port@0 { ++ phy-handle = <ðphy0>; ++ }; ++}; diff --git a/target/linux/kirkwood/patches-4.9/108-on100.patch b/target/linux/kirkwood/patches-4.9/108-on100.patch new file mode 100644 index 0000000000..28c3e535d2 --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/108-on100.patch @@ -0,0 +1,173 @@ +--- /dev/null ++++ b/arch/arm/boot/dts/kirkwood-on100.dts +@@ -0,0 +1,160 @@ ++/dts-v1/; ++ ++#include "kirkwood.dtsi" ++#include "kirkwood-6282.dtsi" ++ ++/ { ++ model = "Cisco Systems ON100"; ++ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood"; ++ ++ memory { ++ device_type = "memory"; ++ reg = <0x00000000 0x20000000>; ++ }; ++ ++ aliases { ++ serial0 = &uart0; ++ }; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200n8 earlyprintk"; ++ stdout-path = "serial0:115200n8"; ++ }; ++ ++ gpio_keys { ++ compatible = "gpio-keys"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-0 = <&pmx_btn_reset>; ++ pinctrl-names = "default"; ++ ++ button@1 { ++ label = "Reset Button"; ++ linux,code = <KEY_RESTART>; ++ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ gpio-leds { ++ compatible = "gpio-leds"; ++ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >; ++ pinctrl-names = "default"; ++ ++ health-g { ++ label = "on100:green:health"; ++ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; ++ }; ++ ++ health-r { ++ label = "on100:red:health"; ++ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; ++ }; ++ ++ health2-g { ++ label = "on100:green:health2"; ++ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; ++ }; ++ ++ health2-r { ++ label = "on100:red:health2"; ++ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++}; ++ ++ð0 { ++ status = "okay"; ++ ++ ethernet0-port@0 { ++ phy-handle = <ðphy0>; ++ phy-connection-type = "rgmii-id"; ++ }; ++}; ++ ++ð1 { ++ status = "okay"; ++ ++ ethernet1-port@0 { ++ phy-handle = <ðphy1>; ++ phy-connection-type = "rgmii-id"; ++ }; ++}; ++ ++&mdio { ++ status = "okay"; ++ ++ ethphy0: ethernet-phy@0 { ++ /* Marvell 88E1121R */ ++ compatible = "ethernet-phy-id0141.0cb0", ++ "ethernet-phy-ieee802.3-c22"; ++ reg = <0>; ++ }; ++ ++ ethphy1: ethernet-phy@1 { ++ /* Marvell 88E1121R */ ++ compatible = "ethernet-phy-id0141.0cb0", ++ "ethernet-phy-ieee802.3-c22"; ++ reg = <1>; ++ }; ++}; ++ ++&nand { ++ status = "okay"; ++ ++ partition@0 { ++ label = "u-boot"; ++ reg = <0x00000000 0x000a0000>; ++ read-only; ++ }; ++ ++ partition@a0000 { ++ label = "u-boot environment"; ++ reg = <0x000a0000 0x00020000>; ++ read-only; ++ }; ++ ++ partition@c0000 { ++ label = "kernel"; ++ reg = <0x000c0000 0x00540000>; ++ }; ++ ++ partition@600000 { ++ label = "ubi"; ++ reg = <0x00600000 0x1fa00000>; ++ }; ++}; ++ ++&pinctrl { ++ pmx_led_health_r: pmx-led-health-r { ++ marvell,pins = "mpp45"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_health_g: pmx-led-health-g { ++ marvell,pins = "mpp44"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_health2_r: pmx-led-health2-r { ++ marvell,pins = "mpp47"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led_health2_g: pmx-led-health2-g { ++ marvell,pins = "mpp46"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_btn_reset: pmx-led-reset { ++ marvell,pins = "mpp31"; ++ marvell,function = "gpio"; ++ }; ++}; ++ ++&sdio { ++ status = "okay"; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -242,6 +242,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ + kirkwood-nsa310s.dtb \ + kirkwood-nsa320.dtb \ + kirkwood-nsa325.dtb \ ++ kirkwood-on100.dtb \ + kirkwood-openblocks_a6.dtb \ + kirkwood-openblocks_a7.dtb \ + kirkwood-openrd-base.dtb \ diff --git a/target/linux/kirkwood/patches-4.9/200-disable-tso.patch b/target/linux/kirkwood/patches-4.9/200-disable-tso.patch new file mode 100644 index 0000000000..cde53d0218 --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/200-disable-tso.patch @@ -0,0 +1,35 @@ +From: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> +Subject: [PATCH] net: mv643xx_eth: Make TSO disabled by default + +Data corruption has been observed to be produced by TSO. For instance, +accessing files on a NFS-server with TSO enabled results in different data +transferred each time. + +This has been observed only on Kirkwood platforms, i.e. with the mv643xx_eth +driver. Same tests on platforms using the mvneta ethernet driver have +passed without errors. + +Make TSO disabled by default for now, until we can found a proper fix +for the regression. + +Fixes: 3ae8f4e0b98 ('net: mv643xx_eth: Implement software TSO') +Reported-by: Slawomir Gajzner <slawomir.gajzner <at> gmail.com> +Reported-by: Julien D'Ascenzio <jdascenzio <at> yahoo.fr> +Signed-off-by: Ezequiel Garcia <ezequiel.garcia <at> free-electrons.com> +--- +--- a/drivers/net/ethernet/marvell/mv643xx_eth.c ++++ b/drivers/net/ethernet/marvell/mv643xx_eth.c +@@ -3197,11 +3197,11 @@ static int mv643xx_eth_probe(struct plat + dev->watchdog_timeo = 2 * HZ; + dev->base_addr = 0; + +- dev->features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO; ++ dev->features = NETIF_F_SG | NETIF_F_IP_CSUM; + dev->vlan_features = dev->features; + + dev->features |= NETIF_F_RXCSUM; +- dev->hw_features = dev->features; ++ dev->hw_features = dev->features | NETIF_F_TSO; + + dev->priv_flags |= IFF_UNICAST_FLT; + dev->gso_max_segs = MV643XX_MAX_TSO_SEGS; diff --git a/target/linux/kirkwood/patches-4.9/201-enable-sata-port-specific-led-triggers.patch b/target/linux/kirkwood/patches-4.9/201-enable-sata-port-specific-led-triggers.patch new file mode 100644 index 0000000000..202c9c02e6 --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/201-enable-sata-port-specific-led-triggers.patch @@ -0,0 +1,10 @@ +--- a/arch/arm/mach-mvebu/Kconfig ++++ b/arch/arm/mach-mvebu/Kconfig +@@ -117,6 +117,7 @@ config MACH_DOVE + config MACH_KIRKWOOD + bool "Marvell Kirkwood boards" + depends on ARCH_MULTI_V5 ++ select ARCH_WANT_LIBATA_LEDS + select CPU_FEROCEON + select GPIOLIB + select KIRKWOOD_CLK diff --git a/target/linux/kirkwood/patches-4.9/202-linksys-find-active-root.patch b/target/linux/kirkwood/patches-4.9/202-linksys-find-active-root.patch new file mode 100644 index 0000000000..28fc153bda --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/202-linksys-find-active-root.patch @@ -0,0 +1,62 @@ +The WRT1900AC among other Linksys routers uses a dual-firmware layout. +Dynamically rename the active partition to "ubi". + +Signed-off-by: Imre Kaloz <kaloz@openwrt.org> +--- +--- a/drivers/mtd/ofpart.c ++++ b/drivers/mtd/ofpart.c +@@ -25,6 +25,8 @@ static bool node_has_compatible(struct d + return of_get_property(pp, "compatible", NULL); + } + ++static int mangled_rootblock; ++ + static int parse_ofpart_partitions(struct mtd_info *master, + const struct mtd_partition **pparts, + struct mtd_part_parser_data *data) +@@ -32,6 +34,7 @@ static int parse_ofpart_partitions(struc + struct mtd_partition *parts; + struct device_node *mtd_node; + struct device_node *ofpart_node; ++ const char *owrtpart = "ubi"; + const char *partname; + struct device_node *pp; + int nr_parts, i, ret = 0; +@@ -110,9 +113,15 @@ static int parse_ofpart_partitions(struc + parts[i].size = of_read_number(reg + a_cells, s_cells); + parts[i].of_node = pp; + +- partname = of_get_property(pp, "label", &len); +- if (!partname) +- partname = of_get_property(pp, "name", &len); ++ if (mangled_rootblock && (i == mangled_rootblock)) { ++ partname = owrtpart; ++ } else { ++ partname = of_get_property(pp, "label", &len); ++ ++ if (!partname) ++ partname = of_get_property(pp, "name", &len); ++ } ++ + parts[i].name = partname; + + if (of_get_property(pp, "read-only", &len)) +@@ -213,6 +222,18 @@ static int __init ofpart_parser_init(voi + return 0; + } + ++static int __init active_root(char *str) ++{ ++ get_option(&str, &mangled_rootblock); ++ ++ if (!mangled_rootblock) ++ return 1; ++ ++ return 1; ++} ++ ++__setup("mangled_rootblock=", active_root); ++ + static void __exit ofpart_parser_exit(void) + { + deregister_mtd_parser(&ofpart_parser); |