diff options
| author | Pawel Dembicki <paweldembicki@gmail.com> | 2020-04-20 10:06:36 +0200 |
|---|---|---|
| committer | Adrian Schmutzler <freifunk@adrianschmutzler.de> | 2020-04-28 16:49:31 +0200 |
| commit | 4fd7e539e4f90128bdd7cb71c729a4b32f5de86e (patch) | |
| tree | 74caf584970ce1d8c1b5c6604e2c228d3a97faea /target/linux/kirkwood/patches-5.4 | |
| parent | 4b3b8ec81cd1965d0bd548fa31db491295b83354 (diff) | |
| download | upstream-4fd7e539e4f90128bdd7cb71c729a4b32f5de86e.tar.gz upstream-4fd7e539e4f90128bdd7cb71c729a4b32f5de86e.tar.bz2 upstream-4fd7e539e4f90128bdd7cb71c729a4b32f5de86e.zip | |
kirkwood: switch from swconfig to dsa
This patch removes support for swconfig and switches to dsa driver.
swconfig and switch drivers are removed. DSA driver is enabled and
configuration is adjusted.
In kirkwood only two devices have switches: Linksys EA3500 and EA4500.
WAN MAC configuration in 02_network is required because otherwise WAN
would have the same MAC address as lan interfaces. In swconfig solution
the WAN address was assigned in u-Boot to eth1. Now, as eth1 is disabled
and wan is part of the switch, we have to set it manually.
Compile tested: EA3500, EA4500
Run tested: EA4500
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[minor commit title/message adjustments, remove swconfig package
for devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Diffstat (limited to 'target/linux/kirkwood/patches-5.4')
| -rw-r--r-- | target/linux/kirkwood/patches-5.4/105-ea4500.patch | 45 |
1 files changed, 1 insertions, 44 deletions
diff --git a/target/linux/kirkwood/patches-5.4/105-ea4500.patch b/target/linux/kirkwood/patches-5.4/105-ea4500.patch index 7302723029..0d97ad14a2 100644 --- a/target/linux/kirkwood/patches-5.4/105-ea4500.patch +++ b/target/linux/kirkwood/patches-5.4/105-ea4500.patch @@ -23,25 +23,7 @@ }; white-pulse { -@@ -66,6 +71,17 @@ - gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; - }; - }; -+ -+ mvsw61xx@10 { -+ compatible = "marvell,88e6171"; -+ status = "okay"; -+ reg = <0x10>; -+ -+ mii-bus = <&mdio>; -+ cpu-port-0 = <5>; -+ cpu-port-1 = <6>; -+ is-indirect; -+ }; - }; - - &pinctrl { -@@ -114,22 +130,22 @@ +@@ -114,22 +119,22 @@ }; partition@200000 { @@ -68,28 +50,3 @@ reg = <0x1EA0000 0x1760000>; }; -@@ -162,6 +178,7 @@ - status = "okay"; - - switch@10 { -+ status = "disabled"; - compatible = "marvell,mv88e6085"; - #address-cells = <1>; - #size-cells = <0>; -@@ -225,10 +242,14 @@ - }; - - /* eth1 is connected to the switch at port 6. However DSA only supports a -- * single CPU port. So leave this port disabled to avoid confusion. -+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion. - */ - ð1 { -- status = "disabled"; -+ status = "okay"; -+ ethernet1-port@0 { -+ speed = <1000>; -+ duplex = <1>; -+ }; - }; - - /* There is no battery on the board, so the RTC does not keep |