kirkwood: drop support for 3.14

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44610

1 files changed, 0 insertions, 127 deletions

diff --git a/target/linux/kirkwood/patches-3.14/150-pogoplug_e02.patch b/target/linux/kirkwood/patches-3.14/150-pogoplug_e02.patch
deleted file mode 100644
index 44b4c52556..0000000000
--- a/target/linux/kirkwood/patches-3.14/150-pogoplug_e02.patch
+++ /dev/null
@@ -1,127 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -112,6 +112,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-
- 	kirkwood-nsa310a.dtb \
- 	kirkwood-openblocks_a6.dtb \
- 	kirkwood-openblocks_a7.dtb \
-+	kirkwood-pogo_e02.dtb \
- 	kirkwood-sheevaplug.dtb \
- 	kirkwood-sheevaplug-esata.dtb \
- 	kirkwood-topkick.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
-@@ -0,0 +1,114 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+
-+/ {
-+	model = "Cloud Engines Pogoplug E02";
-+	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+	memory {
-+		device_type = "memory";
-+		reg = <0x00000000 0x10000000>;
-+	};
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200n8 earlyprintk";
-+	};
-+
-+	ocp@f1000000 {
-+		pinctrl: pinctrl@10000 {
-+			pmx_usb_power_enable: pmx-usb-power-enable {
-+				marvell,pins = "mpp29";
-+				marvell,function = "gpio";
-+			};
-+			pmx_led_green: pmx-led_green {
-+				marvell,pins = "mpp48";
-+				marvell,function = "gpio";
-+			};
-+			pmx_led_orange: pmx-led_orange {
-+				marvell,pins = "mpp49";
-+				marvell,function = "gpio";
-+			};
-+		};
-+		serial@12000 {
-+			status = "ok";
-+		};
-+	};
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+		pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
-+			      &pmx_led_green >;
-+		pinctrl-names = "default";
-+
-+		health {
-+			label = "status:green:health";
-+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
-+			default-state = "keep";
-+		};
-+		fault {
-+			label = "status:orange:fault";
-+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+	regulators {
-+		compatible = "simple-bus";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+		pinctrl-0 = <&pmx_usb_power_enable>;
-+		pinctrl-names = "default";
-+
-+		usb_power: regulator@1 {
-+			compatible = "regulator-fixed";
-+			reg = <1>;
-+			regulator-name = "USB Power";
-+			regulator-min-microvolt = <5000000>;
-+			regulator-max-microvolt = <5000000>;
-+			enable-active-high;
-+			regulator-always-on;
-+			regulator-boot-on;
-+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+		};
-+	};
-+};
-+
-+&nand {
-+	chip-delay = <40>;
-+	status = "okay";
-+
-+	partition@0 {
-+		label = "u-boot";
-+		reg = <0x0000000 0x100000>;
-+		read-only;
-+	};
-+
-+	partition@100000 {
-+		label = "uImage";
-+		reg = <0x0100000 0x400000>;
-+	};
-+
-+	partition@500000 {
-+		label = "pogoplug";
-+		reg = <0x0500000 0x2000000>;
-+	};
-+
-+	partition@2500000 {
-+		label = "root";
-+		reg = <0x02500000 0x5b00000>;
-+	};
-+};
-+
-+&mdio {
-+	status = "okay";
-+
-+	ethphy0: ethernet-phy@0 {
-+		reg = <0>;
-+	};
-+};
-+
-+&eth0 {
-+	status = "okay";
-+	ethernet0-port@0 {
-+		phy-handle = <&ethphy0>;
-+	};
-+};