aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/kirkwood/config-5.4
diff options
context:
space:
mode:
authorPawel Dembicki <paweldembicki@gmail.com>2020-01-26 17:22:28 +0100
committerPetr Štetiar <ynezz@true.cz>2020-07-11 13:33:28 +0200
commit67ce9aedd6d3f7995351f478e79e570c01ea71fc (patch)
treeb63e12a37c4c701204fb6909f129f746cd2a4a4b /target/linux/kirkwood/config-5.4
parentc881d7ab039022aac91a3524227df9cc5f60dd16 (diff)
downloadupstream-67ce9aedd6d3f7995351f478e79e570c01ea71fc.tar.gz
upstream-67ce9aedd6d3f7995351f478e79e570c01ea71fc.tar.bz2
upstream-67ce9aedd6d3f7995351f478e79e570c01ea71fc.zip
kirkwood: add support for Check Point L-50
This patch adds support for the Check Point L-50 from 600/1100 series routers. Specification: -CPU: Marvell Kirkwood 88F6281 1200MHz -RAM: 512MB -Flash: NAND 512MB -WiFi: mPCIe card based on Atheros AR9287 b/g/n -WAN: 1 Gigabit Port (Marvell 88E1116R PHY) -LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4)) -USB: 2x USB2.0 -Express card slot -SD card slot -Serial console: RJ-45 115200 8n1 -Unsupported DSL Known issues: -DSL not supported -Expresscard not tested Installation: Step one -> backup: make backup u-boot and env for revert stock posibility make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr Step two -> Use kwboot tool to upload openwrt u-boot to RAM: run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t" end start u-boot Step three -> Restore macs (e.g. below): setenv eth1addr 00:1C:XX:XX:XX:6C setenv ethaddr 00:1C:XX:XX:XX:6B setenv lan1_mac_addr 00:1C:XX:XX:XX:6C setenv lan2_mac_addr 00:1C:XX:XX:XX:6D setenv lan3_mac_addr 00:1C:XX:XX:XX:6E setenv lan4_mac_addr 00:1C:XX:XX:XX:6F setenv lan5_mac_addr 00:1C:XX:XX:XX:70 setenv lan6_mac_addr 00:1C:XX:XX:XX:71 setenv lan7_mac_addr 00:1C:XX:XX:XX:72 setenv lan8_mac_addr 00:1C:XX:XX:XX:73 setenv dmz_mac_addr 00:1C:XX:XX:XX:74 setenv dsl_mac_addr 00:1C:XX:XX:XX:75 Step four -> flash u-boot: mw 0x0800000 0xffff 0x100000 nand erase 0x0 100000 tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb nand write 0x0800000 0x0 0x100000 saveenv Step five -> run initramfs image: tftpboot 0x02000000 openwrt.bin; bootm 0x02000000; Step six -> install sysupgrade OpenWrt image: copy to /tmp/ sysupgrade image run sysupgrade Back to stock: Restore original u-boot end env. Install factory image via stock u-boot. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Diffstat (limited to 'target/linux/kirkwood/config-5.4')
-rw-r--r--target/linux/kirkwood/config-5.41
1 files changed, 1 insertions, 0 deletions
diff --git a/target/linux/kirkwood/config-5.4 b/target/linux/kirkwood/config-5.4
index 5529bf89df..61efa07d91 100644
--- a/target/linux/kirkwood/config-5.4
+++ b/target/linux/kirkwood/config-5.4
@@ -282,6 +282,7 @@ CONFIG_PINCTRL=y
CONFIG_PINCTRL_KIRKWOOD=y
CONFIG_PINCTRL_MVEBU=y
# CONFIG_PINCTRL_SINGLE is not set
+CONFIG_PINCTRL_SX150X=y
CONFIG_PLAT_ORION=y
CONFIG_POWER_RESET=y
CONFIG_POWER_RESET_GPIO=y