kirkwood: add support for Iomega Storcenter ix2-200

Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell
 Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of
 flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC

Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1000Mhz
- Flash-Chip: Hynix NAND
- Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16
- RAM: 256MB
- LAN: 1x 1000 Mbps Ethernet
- WiFi: none
- 3x USB 2.0
- UART: for serial console

Installation instructions - easy steps:
1. download factory.bin and copy into tftp server
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    setenv serverip 192.168.1.1
    setenv ipaddr 192.168.1.13
    tftpboot 0x00800000 factory.bin
    nand erase 0x100000 $(filesize)
    nand write 0x00800000 0x100000 $(filesize)
    run bootcmd
    ```
3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Installation steps nand bad blocks proof:
1. download initramfs-uImage and copy into usb ext2 partition
    ```
    mkfs.ext2 -L ext2 /dev/sdh1
    mount -t ext2 /dev/sdh1 /mnt
    cp initramfs-uImage /mnt/initramfs.bin
    umount /mnt
    ```
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000
    ```
3. log into openwrt and sysupgrade to install into flash
    ```
    sysupgrade -n /tmp/sysupgrade.bin
    ```
4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>

4 files changed, 15 insertions, 5 deletions

diff --git a/target/linux/kirkwood/base-files/etc/board.d/01_leds b/target/linux/kirkwood/base-files/etc/board.d/01_leds
index 4e72e344aa..5cfc4cf309 100755
--- a/target/linux/kirkwood/base-files/etc/board.d/01_leds
+++ b/target/linux/kirkwood/base-files/etc/board.d/01_leds
@@ -14,6 +14,9 @@ case "$board" in
 	ucidef_set_led_default "health" "health" "pogo_e02:green:health" "1"
 	ucidef_set_led_default "fault" "fault" "pogo_e02:orange:fault" "1"
 	;;
+"iom,ix2-200")
+	ucidef_set_led_timer "health" "health" "status:white:rebuild_led" "200" "800"
+	;;
 "linksys,audi")
 	ucidef_set_led_default "power" "power" "audi:green:power" "1"
 	;;
diff --git a/target/linux/kirkwood/base-files/etc/board.d/02_network b/target/linux/kirkwood/base-files/etc/board.d/02_network
index 5d66e0ffea..15e51d88f2 100755
--- a/target/linux/kirkwood/base-files/etc/board.d/02_network
+++ b/target/linux/kirkwood/base-files/etc/board.d/02_network
@@ -17,6 +17,7 @@ case "$board" in
 "cloudengines,pogoe02"|\
 "cloudengines,pogoplugv4"|\
 "iom,iconnect-1.1"|\
+"iom,ix2-200"|\
 "raidsonic,ib-nas62x0"|\
 "seagate,dockstar"|\
 "seagate,goflexhome"|\
diff --git a/target/linux/kirkwood/base-files/etc/diag.sh b/target/linux/kirkwood/base-files/etc/diag.sh
index 0667ad29fe..fc61846c11 100755
--- a/target/linux/kirkwood/base-files/etc/diag.sh
+++ b/target/linux/kirkwood/base-files/etc/diag.sh
@@ -15,6 +15,9 @@ get_status_led() {
 	cloudengines,pogoplugv4)
 		status_led="pogoplugv4:green:health"
 		;;
+	iom,ix2-200)
+		status_led="status:white:power_led"
+		;;
 	linksys,audi)
 		status_led="audi:green:power"
 		;;
diff --git a/target/linux/kirkwood/base-files/etc/init.d/nsa310_fancontrol b/target/linux/kirkwood/base-files/etc/init.d/hwmon_fancontrol
index 10eb5aa73c..0adc5d0726 100755
--- a/target/linux/kirkwood/base-files/etc/init.d/nsa310_fancontrol
+++ b/target/linux/kirkwood/base-files/etc/init.d/hwmon_fancontrol
@@ -4,17 +4,20 @@ START=98
 boot() {
 . /lib/functions.sh
 
-#configuring lm85 onboard temp/fan controller to run the fan on its own
+#configuring (lm85/lm63) onboard temp/fan controller to run the fan on its own
 #for more information, please read https://www.kernel.org/doc/Documentation/hwmon/sysfs-interface
 
-path_to_hwmon='/sys/devices/platform/ocp@f1000000/f1011000.i2c/i2c-0/0-002e/hwmon/hwmon0'
-
 case $(board_name) in
-	zyxel,nsa310b)
+zyxel,nsa310b)
+	path_to_hwmon='/sys/devices/platform/ocp@f1000000/f1011000.i2c/i2c-0/0-002e/hwmon/hwmon0'
 	echo 2 > "$path_to_hwmon/pwm1_enable" # fan is on pwm1
 	echo 1 > "$path_to_hwmon/pwm1_auto_channels" # temp1 is the only one that changes
 	echo 23000 > "$path_to_hwmon/temp1_auto_temp_min"
 	echo 43000 > "$path_to_hwmon/temp1_auto_temp_max" # next step is 49600 millicelsius, or 50 celsius, 43 celsius is better
-		;;
+	;;
+iom,ix2-200)
+	path_to_hwmon='/sys/class/hwmon/hwmon0'
+	echo 2 > "$path_to_hwmon/pwm1_enable" # fan is on pwm1
+	;;
 esac
 }