diff options
| author | Dirk Buchwalder <buchwalder@posteo.de> | 2022-01-01 23:17:51 +0100 |
|---|---|---|
| committer | Robert Marko <robimarko@gmail.com> | 2023-01-16 12:42:23 +0100 |
| commit | a36fc589fe7ac53ccb83f4503953bd6646477d0a (patch) | |
| tree | f17042390ca53762d5c3320da04492ece107a776 /target/linux/ipq807x/base-files | |
| parent | 8253cb2de59aff81e576ea2655b1d290e4098001 (diff) | |
| download | upstream-a36fc589fe7ac53ccb83f4503953bd6646477d0a.tar.gz upstream-a36fc589fe7ac53ccb83f4503953bd6646477d0a.tar.bz2 upstream-a36fc589fe7ac53ccb83f4503953bd6646477d0a.zip | |
ipq807x: add Edimax CAX1800
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.
Specifications:
• CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
• RAM: 512MB of DDR3
• Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
3 x GPIO-controlled System-LEDs
(form one virtual RGB System-LED)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An unpopulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, but it drops only
to a limited shell .
Installation Instructions:
black_small_square obtain serial access
black_small_square stop auto boot
black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
black_small_square bootm
black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
to the device
black_small_square write the image to the NAND:
black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs-
nand-factory.ubi
black_small_square reboot
Note: Device is not using dual partitioning (NAND contains other partitions
with different manufacture data etc.)
Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Diffstat (limited to 'target/linux/ipq807x/base-files')
3 files changed, 7 insertions, 0 deletions
diff --git a/target/linux/ipq807x/base-files/etc/board.d/02_network b/target/linux/ipq807x/base-files/etc/board.d/02_network index cfe7580f8e..e3f4d4f576 100644 --- a/target/linux/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/ipq807x/base-files/etc/board.d/02_network @@ -11,6 +11,9 @@ ipq807x_setup_interfaces() local board="$1" case "$board" in + edimax,cax1800) + ucidef_set_interfaces_lan_wan "lan" + ;; redmi,ax6|\ xiaomi,ax3600) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan" diff --git a/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index 0a2908f13d..7f919bafc5 100644 --- a/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -9,6 +9,7 @@ board=$(board_name) case "$FIRMWARE" in "ath11k/IPQ8074/hw2.0/cal-ahb-c000000.wifi.bin") case "$board" in + edimax,cax1800|\ redmi,ax6|\ xiaomi,ax3600) caldata_extract "0:art" 0x1000 0x20000 diff --git a/target/linux/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/ipq807x/base-files/lib/upgrade/platform.sh index f9c28fad09..d6e5d04a31 100644 --- a/target/linux/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq807x/base-files/lib/upgrade/platform.sh @@ -42,6 +42,9 @@ platform_pre_upgrade() { platform_do_upgrade() { case "$(board_name)" in + edimax,cax1800) + nand_do_upgrade "$1" + ;; redmi,ax6|\ xiaomi,ax3600) # Make sure that UART is enabled |