ipq807x: add Dynalink DL-WRX36

Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.

Specifications:

    •     CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
    •     RAM: 1024MB of DDR3
    •     Storage: 256MB Nand
    •     Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
          5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
    •     1x USB 3.0

    •     1 gpio-controlled dual color led (blue/red)

            • Buttons: 1x soft reset / 1x WPS
            • Power: 12V DC jack

        A poulated serial header is onboard (J1004)
        the connector size is a 4-pin 2.0 mm JST PH.
        RX/TX is working, u-boot bootwait is active, secure boot is enabled.

        Notes:
	- Serial is completely deactivated in the stock firmware image.
	- This commit adds only single partition support, that means
	  sysupgrade is upgrading the current rootfs partition.
	- Installation can be done by serial connection or
	  SSH access on OEM firmware

	Installation Instructions:

	Most part of the installation is performed from an initramfs image
	running OpenWrt, and there are two options to boot it.

	Boot initramfs option 1: Using serial connection (3.3V)
	1. Stop auto boot to get to U-boot shell
	2. Transfer initramfs image to device
	   (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
	   Tested using TFTP and a FAT-formatted USB flash drive.
	3. Boot the initramfs image
	   # bootm

	Boot initramfs option 2: From SSH access on OEM firmware
	1. Copy the initramfs image to a FAT-formatted flash drive
	   (tested on single-partition drive) and connect it to device USB port.
	2. Change boot command so it loads the initramfs image on next boot
	   Fallback to OEM firmware is provided.
	   # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
	3. Reboot the device to boot the initramfs
	   # reboot

	Install OpenWrt from initramfs image:
	1. Use SCP (or other way) to transfer OpenWrt factory image
	2. Connect to device using SSH (on a LAN port)
	3. Check MTD partition table.
	   rootfs and rootfs_1 should be mtd18 and mtd20
	   depending on current OEM slot.
	   # cat /proc/mtd
	4. Do a ubiformat to both rootfs partitions:
	   # ubiformat /dev/mtd18 -y -f /path_to/factory_image
	   # ubiformat /dev/mtd20 -y -f /path_to/factory_image
	5. Set U-boot env variable: mtdids
	   # fw_setenv mtdids 'nand0=nand0'
	6. Get offset of mtd18 to determine current OEM slot
	   - If current OEM slot is 1, offset is 16777216  (0x1000000)
	   - If current OEM slot is 2, offset is 127926272 (0x7a00000)
	   # cat /sys/class/mtd/mtd18/offset
	7. Set U-boot env variable: mtdparts
	   If current OEM slot is 1, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
	   If current OEM slot is 2, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
	8. Set U-boot env variable: bootcmd
	   # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
	9. Reboot the device
	   # reboot

        Note: this PR adds only single partition support, that means sysupgrade is
              upgrading the current rootfs partition

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>

2 files changed, 4 insertions, 0 deletions

diff --git a/target/linux/ipq807x/base-files/etc/board.d/02_network b/target/linux/ipq807x/base-files/etc/board.d/02_network
index 8856daff31..e2bd46f095 100644
--- a/target/linux/ipq807x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq807x/base-files/etc/board.d/02_network
@@ -11,6 +11,9 @@ ipq807x_setup_interfaces()
 	local board="$1"
 
 	case "$board" in
+	dynalink,dl-wrx36)
+		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
+		;;
 	edgecore,eap102)
 		ucidef_set_interfaces_lan_wan "lan" "wan"
 		;;
diff --git a/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
index a2290ac124..974e7607aa 100644
--- a/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
+++ b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
@@ -11,6 +11,7 @@ case "$FIRMWARE" in
 	case "$board" in
 	edgecore,eap102|\
 	edimax,cax1800|\
+	dynalink,dl-wrx36|\
 	qnap,301w|\
 	redmi,ax6|\
 	xiaomi,ax3600|\