ipq806x: 5:15: drop upstream patch

- Drop stmmac upstream patches
- Drop tsens patches
- Drop ADM driver
- Drop SMEM parser

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>

14 files changed, 0 insertions, 2244 deletions

diff --git a/target/linux/ipq806x/patches-5.15/100-v5.11-dmaengine-qcom-add_ADM_driver.patch b/target/linux/ipq806x/patches-5.15/100-v5.11-dmaengine-qcom-add_ADM_driver.patch
deleted file mode 100644
index 2d24da01e4..0000000000
--- a/target/linux/ipq806x/patches-5.15/100-v5.11-dmaengine-qcom-add_ADM_driver.patch
+++ /dev/null
@@ -1,965 +0,0 @@
-From 5c9f8c2dbdbe53818bcde6aa6695e1331e5f841f Mon Sep 17 00:00:00 2001
-From: Jonathan McDowell <noodles@earth.li>
-Date: Sat, 14 Nov 2020 14:02:33 +0000
-Subject: dmaengine: qcom: Add ADM driver
-
-Add the DMA engine driver for the QCOM Application Data Mover (ADM) DMA
-controller found in the MSM8x60 and IPQ/APQ8064 platforms.
-
-The ADM supports both memory to memory transactions and memory
-to/from peripheral device transactions.  The controller also provides
-flow control capabilities for transactions to/from peripheral devices.
-
-The initial release of this driver supports slave transfers to/from
-peripherals and also incorporates CRCI (client rate control interface)
-flow control.
-
-The hardware only supports a 32 bit physical address, so specifying
-!PHYS_ADDR_T_64BIT gives maximum COMPILE_TEST coverage without having to
-spend effort on kludging things in the code that will never actually be
-needed on real hardware.
-
-Signed-off-by: Andy Gross <agross@codeaurora.org>
-Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
-Signed-off-by: Jonathan McDowell <noodles@earth.li>
-Link: https://lore.kernel.org/r/20201114140233.GM32650@earth.li
-Signed-off-by: Vinod Koul <vkoul@kernel.org>
----
- drivers/dma/qcom/Kconfig    |  11 +
- drivers/dma/qcom/Makefile   |   1 +
- drivers/dma/qcom/qcom_adm.c | 903 ++++++++++++++++++++++++++++++++++++++++++++
- 3 files changed, 915 insertions(+)
- create mode 100644 drivers/dma/qcom/qcom_adm.c
-
---- a/drivers/dma/qcom/Kconfig
-+++ b/drivers/dma/qcom/Kconfig
-@@ -1,4 +1,15 @@
- # SPDX-License-Identifier: GPL-2.0-only
-+config QCOM_ADM
-+	tristate "Qualcomm ADM support"
-+	depends on (ARCH_QCOM || COMPILE_TEST) && !PHYS_ADDR_T_64BIT
-+	select DMA_ENGINE
-+	select DMA_VIRTUAL_CHANNELS
-+	help
-+	  Enable support for the Qualcomm Application Data Mover (ADM) DMA
-+	  controller, as present on MSM8x60, APQ8064, and IPQ8064 devices.
-+	  This controller provides DMA capabilities for both general purpose
-+	  and on-chip peripheral devices.
-+
- config QCOM_BAM_DMA
- 	tristate "QCOM BAM DMA support"
- 	depends on ARCH_QCOM || (COMPILE_TEST && OF && ARM)
---- a/drivers/dma/qcom/Makefile
-+++ b/drivers/dma/qcom/Makefile
-@@ -1,4 +1,5 @@
- # SPDX-License-Identifier: GPL-2.0
-+obj-$(CONFIG_QCOM_ADM) += qcom_adm.o
- obj-$(CONFIG_QCOM_BAM_DMA) += bam_dma.o
- obj-$(CONFIG_QCOM_HIDMA_MGMT) += hdma_mgmt.o
- hdma_mgmt-objs	 := hidma_mgmt.o hidma_mgmt_sys.o
---- /dev/null
-+++ b/drivers/dma/qcom/qcom_adm.c
-@@ -0,0 +1,903 @@
-+// SPDX-License-Identifier: GPL-2.0-only
-+/*
-+ * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
-+ */
-+
-+#include <linux/clk.h>
-+#include <linux/delay.h>
-+#include <linux/device.h>
-+#include <linux/dmaengine.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/init.h>
-+#include <linux/interrupt.h>
-+#include <linux/io.h>
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/of_address.h>
-+#include <linux/of_irq.h>
-+#include <linux/of_dma.h>
-+#include <linux/platform_device.h>
-+#include <linux/reset.h>
-+#include <linux/scatterlist.h>
-+#include <linux/slab.h>
-+
-+#include "../dmaengine.h"
-+#include "../virt-dma.h"
-+
-+/* ADM registers - calculated from channel number and security domain */
-+#define ADM_CHAN_MULTI			0x4
-+#define ADM_CI_MULTI			0x4
-+#define ADM_CRCI_MULTI			0x4
-+#define ADM_EE_MULTI			0x800
-+#define ADM_CHAN_OFFS(chan)		(ADM_CHAN_MULTI * (chan))
-+#define ADM_EE_OFFS(ee)			(ADM_EE_MULTI * (ee))
-+#define ADM_CHAN_EE_OFFS(chan, ee)	(ADM_CHAN_OFFS(chan) + ADM_EE_OFFS(ee))
-+#define ADM_CHAN_OFFS(chan)		(ADM_CHAN_MULTI * (chan))
-+#define ADM_CI_OFFS(ci)			(ADM_CHAN_OFF(ci))
-+#define ADM_CH_CMD_PTR(chan, ee)	(ADM_CHAN_EE_OFFS(chan, ee))
-+#define ADM_CH_RSLT(chan, ee)		(0x40 + ADM_CHAN_EE_OFFS(chan, ee))
-+#define ADM_CH_FLUSH_STATE0(chan, ee)	(0x80 + ADM_CHAN_EE_OFFS(chan, ee))
-+#define ADM_CH_STATUS_SD(chan, ee)	(0x200 + ADM_CHAN_EE_OFFS(chan, ee))
-+#define ADM_CH_CONF(chan)		(0x240 + ADM_CHAN_OFFS(chan))
-+#define ADM_CH_RSLT_CONF(chan, ee)	(0x300 + ADM_CHAN_EE_OFFS(chan, ee))
-+#define ADM_SEC_DOMAIN_IRQ_STATUS(ee)	(0x380 + ADM_EE_OFFS(ee))
-+#define ADM_CI_CONF(ci)			(0x390 + (ci) * ADM_CI_MULTI)
-+#define ADM_GP_CTL			0x3d8
-+#define ADM_CRCI_CTL(crci, ee)		(0x400 + (crci) * ADM_CRCI_MULTI + \
-+						ADM_EE_OFFS(ee))
-+
-+/* channel status */
-+#define ADM_CH_STATUS_VALID		BIT(1)
-+
-+/* channel result */
-+#define ADM_CH_RSLT_VALID		BIT(31)
-+#define ADM_CH_RSLT_ERR			BIT(3)
-+#define ADM_CH_RSLT_FLUSH		BIT(2)
-+#define ADM_CH_RSLT_TPD			BIT(1)
-+
-+/* channel conf */
-+#define ADM_CH_CONF_SHADOW_EN		BIT(12)
-+#define ADM_CH_CONF_MPU_DISABLE		BIT(11)
-+#define ADM_CH_CONF_PERM_MPU_CONF	BIT(9)
-+#define ADM_CH_CONF_FORCE_RSLT_EN	BIT(7)
-+#define ADM_CH_CONF_SEC_DOMAIN(ee)	((((ee) & 0x3) << 4) | (((ee) & 0x4) << 11))
-+
-+/* channel result conf */
-+#define ADM_CH_RSLT_CONF_FLUSH_EN	BIT(1)
-+#define ADM_CH_RSLT_CONF_IRQ_EN		BIT(0)
-+
-+/* CRCI CTL */
-+#define ADM_CRCI_CTL_MUX_SEL		BIT(18)
-+#define ADM_CRCI_CTL_RST		BIT(17)
-+
-+/* CI configuration */
-+#define ADM_CI_RANGE_END(x)		((x) << 24)
-+#define ADM_CI_RANGE_START(x)		((x) << 16)
-+#define ADM_CI_BURST_4_WORDS		BIT(2)
-+#define ADM_CI_BURST_8_WORDS		BIT(3)
-+
-+/* GP CTL */
-+#define ADM_GP_CTL_LP_EN		BIT(12)
-+#define ADM_GP_CTL_LP_CNT(x)		((x) << 8)
-+
-+/* Command pointer list entry */
-+#define ADM_CPLE_LP			BIT(31)
-+#define ADM_CPLE_CMD_PTR_LIST		BIT(29)
-+
-+/* Command list entry */
-+#define ADM_CMD_LC			BIT(31)
-+#define ADM_CMD_DST_CRCI(n)		(((n) & 0xf) << 7)
-+#define ADM_CMD_SRC_CRCI(n)		(((n) & 0xf) << 3)
-+
-+#define ADM_CMD_TYPE_SINGLE		0x0
-+#define ADM_CMD_TYPE_BOX		0x3
-+
-+#define ADM_CRCI_MUX_SEL		BIT(4)
-+#define ADM_DESC_ALIGN			8
-+#define ADM_MAX_XFER			(SZ_64K - 1)
-+#define ADM_MAX_ROWS			(SZ_64K - 1)
-+#define ADM_MAX_CHANNELS		16
-+
-+struct adm_desc_hw_box {
-+	u32 cmd;
-+	u32 src_addr;
-+	u32 dst_addr;
-+	u32 row_len;
-+	u32 num_rows;
-+	u32 row_offset;
-+};
-+
-+struct adm_desc_hw_single {
-+	u32 cmd;
-+	u32 src_addr;
-+	u32 dst_addr;
-+	u32 len;
-+};
-+
-+struct adm_async_desc {
-+	struct virt_dma_desc vd;
-+	struct adm_device *adev;
-+
-+	size_t length;
-+	enum dma_transfer_direction dir;
-+	dma_addr_t dma_addr;
-+	size_t dma_len;
-+
-+	void *cpl;
-+	dma_addr_t cp_addr;
-+	u32 crci;
-+	u32 mux;
-+	u32 blk_size;
-+};
-+
-+struct adm_chan {
-+	struct virt_dma_chan vc;
-+	struct adm_device *adev;
-+
-+	/* parsed from DT */
-+	u32 id;			/* channel id */
-+
-+	struct adm_async_desc *curr_txd;
-+	struct dma_slave_config slave;
-+	struct list_head node;
-+
-+	int error;
-+	int initialized;
-+};
-+
-+static inline struct adm_chan *to_adm_chan(struct dma_chan *common)
-+{
-+	return container_of(common, struct adm_chan, vc.chan);
-+}
-+
-+struct adm_device {
-+	void __iomem *regs;
-+	struct device *dev;
-+	struct dma_device common;
-+	struct device_dma_parameters dma_parms;
-+	struct adm_chan *channels;
-+
-+	u32 ee;
-+
-+	struct clk *core_clk;
-+	struct clk *iface_clk;
-+
-+	struct reset_control *clk_reset;
-+	struct reset_control *c0_reset;
-+	struct reset_control *c1_reset;
-+	struct reset_control *c2_reset;
-+	int irq;
-+};
-+
-+/**
-+ * adm_free_chan - Frees dma resources associated with the specific channel
-+ *
-+ * Free all allocated descriptors associated with this channel
-+ *
-+ */
-+static void adm_free_chan(struct dma_chan *chan)
-+{
-+	/* free all queued descriptors */
-+	vchan_free_chan_resources(to_virt_chan(chan));
-+}
-+
-+/**
-+ * adm_get_blksize - Get block size from burst value
-+ *
-+ */
-+static int adm_get_blksize(unsigned int burst)
-+{
-+	int ret;
-+
-+	switch (burst) {
-+	case 16:
-+	case 32:
-+	case 64:
-+	case 128:
-+		ret = ffs(burst >> 4) - 1;
-+		break;
-+	case 192:
-+		ret = 4;
-+		break;
-+	case 256:
-+		ret = 5;
-+		break;
-+	default:
-+		ret = -EINVAL;
-+		break;
-+	}
-+
-+	return ret;
-+}
-+
-+/**
-+ * adm_process_fc_descriptors - Process descriptors for flow controlled xfers
-+ *
-+ * @achan: ADM channel
-+ * @desc: Descriptor memory pointer
-+ * @sg: Scatterlist entry
-+ * @crci: CRCI value
-+ * @burst: Burst size of transaction
-+ * @direction: DMA transfer direction
-+ */
-+static void *adm_process_fc_descriptors(struct adm_chan *achan, void *desc,
-+					struct scatterlist *sg, u32 crci,
-+					u32 burst,
-+					enum dma_transfer_direction direction)
-+{
-+	struct adm_desc_hw_box *box_desc = NULL;
-+	struct adm_desc_hw_single *single_desc;
-+	u32 remainder = sg_dma_len(sg);
-+	u32 rows, row_offset, crci_cmd;
-+	u32 mem_addr = sg_dma_address(sg);
-+	u32 *incr_addr = &mem_addr;
-+	u32 *src, *dst;
-+
-+	if (direction == DMA_DEV_TO_MEM) {
-+		crci_cmd = ADM_CMD_SRC_CRCI(crci);
-+		row_offset = burst;
-+		src = &achan->slave.src_addr;
-+		dst = &mem_addr;
-+	} else {
-+		crci_cmd = ADM_CMD_DST_CRCI(crci);
-+		row_offset = burst << 16;
-+		src = &mem_addr;
-+		dst = &achan->slave.dst_addr;
-+	}
-+
-+	while (remainder >= burst) {
-+		box_desc = desc;
-+		box_desc->cmd = ADM_CMD_TYPE_BOX | crci_cmd;
-+		box_desc->row_offset = row_offset;
-+		box_desc->src_addr = *src;
-+		box_desc->dst_addr = *dst;
-+
-+		rows = remainder / burst;
-+		rows = min_t(u32, rows, ADM_MAX_ROWS);
-+		box_desc->num_rows = rows << 16 | rows;
-+		box_desc->row_len = burst << 16 | burst;
-+
-+		*incr_addr += burst * rows;
-+		remainder -= burst * rows;
-+		desc += sizeof(*box_desc);
-+	}
-+
-+	/* if leftover bytes, do one single descriptor */
-+	if (remainder) {
-+		single_desc = desc;
-+		single_desc->cmd = ADM_CMD_TYPE_SINGLE | crci_cmd;
-+		single_desc->len = remainder;
-+		single_desc->src_addr = *src;
-+		single_desc->dst_addr = *dst;
-+		desc += sizeof(*single_desc);
-+
-+		if (sg_is_last(sg))
-+			single_desc->cmd |= ADM_CMD_LC;
-+	} else {
-+		if (box_desc && sg_is_last(sg))
-+			box_desc->cmd |= ADM_CMD_LC;
-+	}
-+
-+	return desc;
-+}
-+
-+/**
-+ * adm_process_non_fc_descriptors - Process descriptors for non-fc xfers
-+ *
-+ * @achan: ADM channel
-+ * @desc: Descriptor memory pointer
-+ * @sg: Scatterlist entry
-+ * @direction: DMA transfer direction
-+ */
-+static void *adm_process_non_fc_descriptors(struct adm_chan *achan, void *desc,
-+					    struct scatterlist *sg,
-+					    enum dma_transfer_direction direction)
-+{
-+	struct adm_desc_hw_single *single_desc;
-+	u32 remainder = sg_dma_len(sg);
-+	u32 mem_addr = sg_dma_address(sg);
-+	u32 *incr_addr = &mem_addr;
-+	u32 *src, *dst;
-+
-+	if (direction == DMA_DEV_TO_MEM) {
-+		src = &achan->slave.src_addr;
-+		dst = &mem_addr;
-+	} else {
-+		src = &mem_addr;
-+		dst = &achan->slave.dst_addr;
-+	}
-+
-+	do {
-+		single_desc = desc;
-+		single_desc->cmd = ADM_CMD_TYPE_SINGLE;
-+		single_desc->src_addr = *src;
-+		single_desc->dst_addr = *dst;
-+		single_desc->len = (remainder > ADM_MAX_XFER) ?
-+				ADM_MAX_XFER : remainder;
-+
-+		remainder -= single_desc->len;
-+		*incr_addr += single_desc->len;
-+		desc += sizeof(*single_desc);
-+	} while (remainder);
-+
-+	/* set last command if this is the end of the whole transaction */
-+	if (sg_is_last(sg))
-+		single_desc->cmd |= ADM_CMD_LC;
-+
-+	return desc;
-+}
-+
-+/**
-+ * adm_prep_slave_sg - Prep slave sg transaction
-+ *
-+ * @chan: dma channel
-+ * @sgl: scatter gather list
-+ * @sg_len: length of sg
-+ * @direction: DMA transfer direction
-+ * @flags: DMA flags
-+ * @context: transfer context (unused)
-+ */
-+static struct dma_async_tx_descriptor *adm_prep_slave_sg(struct dma_chan *chan,
-+							 struct scatterlist *sgl,
-+							 unsigned int sg_len,
-+							 enum dma_transfer_direction direction,
-+							 unsigned long flags,
-+							 void *context)
-+{
-+	struct adm_chan *achan = to_adm_chan(chan);
-+	struct adm_device *adev = achan->adev;
-+	struct adm_async_desc *async_desc;
-+	struct scatterlist *sg;
-+	dma_addr_t cple_addr;
-+	u32 i, burst;
-+	u32 single_count = 0, box_count = 0, crci = 0;
-+	void *desc;
-+	u32 *cple;
-+	int blk_size = 0;
-+
-+	if (!is_slave_direction(direction)) {
-+		dev_err(adev->dev, "invalid dma direction\n");
-+		return NULL;
-+	}
-+
-+	/*
-+	 * get burst value from slave configuration
-+	 */
-+	burst = (direction == DMA_MEM_TO_DEV) ?
-+		achan->slave.dst_maxburst :
-+		achan->slave.src_maxburst;
-+
-+	/* if using flow control, validate burst and crci values */
-+	if (achan->slave.device_fc) {
-+		blk_size = adm_get_blksize(burst);
-+		if (blk_size < 0) {
-+			dev_err(adev->dev, "invalid burst value: %d\n",
-+				burst);
-+			return ERR_PTR(-EINVAL);
-+		}
-+
-+		crci = achan->slave.slave_id & 0xf;
-+		if (!crci || achan->slave.slave_id > 0x1f) {
-+			dev_err(adev->dev, "invalid crci value\n");
-+			return ERR_PTR(-EINVAL);
-+		}
-+	}
-+
-+	/* iterate through sgs and compute allocation size of structures */
-+	for_each_sg(sgl, sg, sg_len, i) {
-+		if (achan->slave.device_fc) {
-+			box_count += DIV_ROUND_UP(sg_dma_len(sg) / burst,
-+						  ADM_MAX_ROWS);
-+			if (sg_dma_len(sg) % burst)
-+				single_count++;
-+		} else {
-+			single_count += DIV_ROUND_UP(sg_dma_len(sg),
-+						     ADM_MAX_XFER);
-+		}
-+	}
-+
-+	async_desc = kzalloc(sizeof(*async_desc), GFP_NOWAIT);
-+	if (!async_desc)
-+		return ERR_PTR(-ENOMEM);
-+
-+	if (crci)
-+		async_desc->mux = achan->slave.slave_id & ADM_CRCI_MUX_SEL ?
-+					ADM_CRCI_CTL_MUX_SEL : 0;
-+	async_desc->crci = crci;
-+	async_desc->blk_size = blk_size;
-+	async_desc->dma_len = single_count * sizeof(struct adm_desc_hw_single) +
-+				box_count * sizeof(struct adm_desc_hw_box) +
-+				sizeof(*cple) + 2 * ADM_DESC_ALIGN;
-+
-+	async_desc->cpl = kzalloc(async_desc->dma_len, GFP_NOWAIT);
-+	if (!async_desc->cpl)
-+		goto free;
-+
-+	async_desc->adev = adev;
-+
-+	/* both command list entry and descriptors must be 8 byte aligned */
-+	cple = PTR_ALIGN(async_desc->cpl, ADM_DESC_ALIGN);
-+	desc = PTR_ALIGN(cple + 1, ADM_DESC_ALIGN);
-+
-+	for_each_sg(sgl, sg, sg_len, i) {
-+		async_desc->length += sg_dma_len(sg);
-+
-+		if (achan->slave.device_fc)
-+			desc = adm_process_fc_descriptors(achan, desc, sg, crci,
-+							  burst, direction);
-+		else
-+			desc = adm_process_non_fc_descriptors(achan, desc, sg,
-+							      direction);
-+	}
-+
-+	async_desc->dma_addr = dma_map_single(adev->dev, async_desc->cpl,
-+					      async_desc->dma_len,
-+					      DMA_TO_DEVICE);
-+	if (dma_mapping_error(adev->dev, async_desc->dma_addr))
-+		goto free;
-+
-+	cple_addr = async_desc->dma_addr + ((void *)cple - async_desc->cpl);
-+
-+	/* init cmd list */
-+	dma_sync_single_for_cpu(adev->dev, cple_addr, sizeof(*cple),
-+				DMA_TO_DEVICE);
-+	*cple = ADM_CPLE_LP;
-+	*cple |= (async_desc->dma_addr + ADM_DESC_ALIGN) >> 3;
-+	dma_sync_single_for_device(adev->dev, cple_addr, sizeof(*cple),
-+				   DMA_TO_DEVICE);
-+
-+	return vchan_tx_prep(&achan->vc, &async_desc->vd, flags);
-+
-+free:
-+	kfree(async_desc);
-+	return ERR_PTR(-ENOMEM);
-+}
-+
-+/**
-+ * adm_terminate_all - terminate all transactions on a channel
-+ * @achan: adm dma channel
-+ *
-+ * Dequeues and frees all transactions, aborts current transaction
-+ * No callbacks are done
-+ *
-+ */
-+static int adm_terminate_all(struct dma_chan *chan)
-+{
-+	struct adm_chan *achan = to_adm_chan(chan);
-+	struct adm_device *adev = achan->adev;
-+	unsigned long flags;
-+	LIST_HEAD(head);
-+
-+	spin_lock_irqsave(&achan->vc.lock, flags);
-+	vchan_get_all_descriptors(&achan->vc, &head);
-+
-+	/* send flush command to terminate current transaction */
-+	writel_relaxed(0x0,
-+		       adev->regs + ADM_CH_FLUSH_STATE0(achan->id, adev->ee));
-+
-+	spin_unlock_irqrestore(&achan->vc.lock, flags);
-+
-+	vchan_dma_desc_free_list(&achan->vc, &head);
-+
-+	return 0;
-+}
-+
-+static int adm_slave_config(struct dma_chan *chan, struct dma_slave_config *cfg)
-+{
-+	struct adm_chan *achan = to_adm_chan(chan);
-+	unsigned long flag;
-+
-+	spin_lock_irqsave(&achan->vc.lock, flag);
-+	memcpy(&achan->slave, cfg, sizeof(struct dma_slave_config));
-+	spin_unlock_irqrestore(&achan->vc.lock, flag);
-+
-+	return 0;
-+}
-+
-+/**
-+ * adm_start_dma - start next transaction
-+ * @achan - ADM dma channel
-+ */
-+static void adm_start_dma(struct adm_chan *achan)
-+{
-+	struct virt_dma_desc *vd = vchan_next_desc(&achan->vc);
-+	struct adm_device *adev = achan->adev;
-+	struct adm_async_desc *async_desc;
-+
-+	lockdep_assert_held(&achan->vc.lock);
-+
-+	if (!vd)
-+		return;
-+
-+	list_del(&vd->node);
-+
-+	/* write next command list out to the CMD FIFO */
-+	async_desc = container_of(vd, struct adm_async_desc, vd);
-+	achan->curr_txd = async_desc;
-+
-+	/* reset channel error */
-+	achan->error = 0;
-+
-+	if (!achan->initialized) {
-+		/* enable interrupts */
-+		writel(ADM_CH_CONF_SHADOW_EN |
-+		       ADM_CH_CONF_PERM_MPU_CONF |
-+		       ADM_CH_CONF_MPU_DISABLE |
-+		       ADM_CH_CONF_SEC_DOMAIN(adev->ee),
-+		       adev->regs + ADM_CH_CONF(achan->id));
-+
-+		writel(ADM_CH_RSLT_CONF_IRQ_EN | ADM_CH_RSLT_CONF_FLUSH_EN,
-+		       adev->regs + ADM_CH_RSLT_CONF(achan->id, adev->ee));
-+
-+		achan->initialized = 1;
-+	}
-+
-+	/* set the crci block size if this transaction requires CRCI */
-+	if (async_desc->crci) {
-+		writel(async_desc->mux | async_desc->blk_size,
-+		       adev->regs + ADM_CRCI_CTL(async_desc->crci, adev->ee));
-+	}
-+
-+	/* make sure IRQ enable doesn't get reordered */
-+	wmb();
-+
-+	/* write next command list out to the CMD FIFO */
-+	writel(ALIGN(async_desc->dma_addr, ADM_DESC_ALIGN) >> 3,
-+	       adev->regs + ADM_CH_CMD_PTR(achan->id, adev->ee));
-+}
-+
-+/**
-+ * adm_dma_irq - irq handler for ADM controller
-+ * @irq: IRQ of interrupt
-+ * @data: callback data
-+ *
-+ * IRQ handler for the bam controller
-+ */
-+static irqreturn_t adm_dma_irq(int irq, void *data)
-+{
-+	struct adm_device *adev = data;
-+	u32 srcs, i;
-+	struct adm_async_desc *async_desc;
-+	unsigned long flags;
-+
-+	srcs = readl_relaxed(adev->regs +
-+			ADM_SEC_DOMAIN_IRQ_STATUS(adev->ee));
-+
-+	for (i = 0; i < ADM_MAX_CHANNELS; i++) {
-+		struct adm_chan *achan = &adev->channels[i];
-+		u32 status, result;
-+
-+		if (srcs & BIT(i)) {
-+			status = readl_relaxed(adev->regs +
-+					       ADM_CH_STATUS_SD(i, adev->ee));
-+
-+			/* if no result present, skip */
-+			if (!(status & ADM_CH_STATUS_VALID))
-+				continue;
-+
-+			result = readl_relaxed(adev->regs +
-+				ADM_CH_RSLT(i, adev->ee));
-+
-+			/* no valid results, skip */
-+			if (!(result & ADM_CH_RSLT_VALID))
-+				continue;
-+
-+			/* flag error if transaction was flushed or failed */
-+			if (result & (ADM_CH_RSLT_ERR | ADM_CH_RSLT_FLUSH))
-+				achan->error = 1;
-+
-+			spin_lock_irqsave(&achan->vc.lock, flags);
-+			async_desc = achan->curr_txd;
-+
-+			achan->curr_txd = NULL;
-+
-+			if (async_desc) {
-+				vchan_cookie_complete(&async_desc->vd);
-+
-+				/* kick off next DMA */
-+				adm_start_dma(achan);
-+			}
-+
-+			spin_unlock_irqrestore(&achan->vc.lock, flags);
-+		}
-+	}
-+
-+	return IRQ_HANDLED;
-+}
-+
-+/**
-+ * adm_tx_status - returns status of transaction
-+ * @chan: dma channel
-+ * @cookie: transaction cookie
-+ * @txstate: DMA transaction state
-+ *
-+ * Return status of dma transaction
-+ */
-+static enum dma_status adm_tx_status(struct dma_chan *chan, dma_cookie_t cookie,
-+				     struct dma_tx_state *txstate)
-+{
-+	struct adm_chan *achan = to_adm_chan(chan);
-+	struct virt_dma_desc *vd;
-+	enum dma_status ret;
-+	unsigned long flags;
-+	size_t residue = 0;
-+
-+	ret = dma_cookie_status(chan, cookie, txstate);
-+	if (ret == DMA_COMPLETE || !txstate)
-+		return ret;
-+
-+	spin_lock_irqsave(&achan->vc.lock, flags);
-+
-+	vd = vchan_find_desc(&achan->vc, cookie);
-+	if (vd)
-+		residue = container_of(vd, struct adm_async_desc, vd)->length;
-+
-+	spin_unlock_irqrestore(&achan->vc.lock, flags);
-+
-+	/*
-+	 * residue is either the full length if it is in the issued list, or 0
-+	 * if it is in progress.  We have no reliable way of determining
-+	 * anything inbetween
-+	 */
-+	dma_set_residue(txstate, residue);
-+
-+	if (achan->error)
-+		return DMA_ERROR;
-+
-+	return ret;
-+}
-+
-+/**
-+ * adm_issue_pending - starts pending transactions
-+ * @chan: dma channel
-+ *
-+ * Issues all pending transactions and starts DMA
-+ */
-+static void adm_issue_pending(struct dma_chan *chan)
-+{
-+	struct adm_chan *achan = to_adm_chan(chan);
-+	unsigned long flags;
-+
-+	spin_lock_irqsave(&achan->vc.lock, flags);
-+
-+	if (vchan_issue_pending(&achan->vc) && !achan->curr_txd)
-+		adm_start_dma(achan);
-+	spin_unlock_irqrestore(&achan->vc.lock, flags);
-+}
-+
-+/**
-+ * adm_dma_free_desc - free descriptor memory
-+ * @vd: virtual descriptor
-+ *
-+ */
-+static void adm_dma_free_desc(struct virt_dma_desc *vd)
-+{
-+	struct adm_async_desc *async_desc = container_of(vd,
-+			struct adm_async_desc, vd);
-+
-+	dma_unmap_single(async_desc->adev->dev, async_desc->dma_addr,
-+			 async_desc->dma_len, DMA_TO_DEVICE);
-+	kfree(async_desc->cpl);
-+	kfree(async_desc);
-+}
-+
-+static void adm_channel_init(struct adm_device *adev, struct adm_chan *achan,
-+			     u32 index)
-+{
-+	achan->id = index;
-+	achan->adev = adev;
-+
-+	vchan_init(&achan->vc, &adev->common);
-+	achan->vc.desc_free = adm_dma_free_desc;
-+}
-+
-+static int adm_dma_probe(struct platform_device *pdev)
-+{
-+	struct adm_device *adev;
-+	int ret;
-+	u32 i;
-+
-+	adev = devm_kzalloc(&pdev->dev, sizeof(*adev), GFP_KERNEL);
-+	if (!adev)
-+		return -ENOMEM;
-+
-+	adev->dev = &pdev->dev;
-+
-+	adev->regs = devm_platform_ioremap_resource(pdev, 0);
-+	if (IS_ERR(adev->regs))
-+		return PTR_ERR(adev->regs);
-+
-+	adev->irq = platform_get_irq(pdev, 0);
-+	if (adev->irq < 0)
-+		return adev->irq;
-+
-+	ret = of_property_read_u32(pdev->dev.of_node, "qcom,ee", &adev->ee);
-+	if (ret) {
-+		dev_err(adev->dev, "Execution environment unspecified\n");
-+		return ret;
-+	}
-+
-+	adev->core_clk = devm_clk_get(adev->dev, "core");
-+	if (IS_ERR(adev->core_clk))
-+		return PTR_ERR(adev->core_clk);
-+
-+	adev->iface_clk = devm_clk_get(adev->dev, "iface");
-+	if (IS_ERR(adev->iface_clk))
-+		return PTR_ERR(adev->iface_clk);
-+
-+	adev->clk_reset = devm_reset_control_get_exclusive(&pdev->dev, "clk");
-+	if (IS_ERR(adev->clk_reset)) {
-+		dev_err(adev->dev, "failed to get ADM0 reset\n");
-+		return PTR_ERR(adev->clk_reset);
-+	}
-+
-+	adev->c0_reset = devm_reset_control_get_exclusive(&pdev->dev, "c0");
-+	if (IS_ERR(adev->c0_reset)) {
-+		dev_err(adev->dev, "failed to get ADM0 C0 reset\n");
-+		return PTR_ERR(adev->c0_reset);
-+	}
-+
-+	adev->c1_reset = devm_reset_control_get_exclusive(&pdev->dev, "c1");
-+	if (IS_ERR(adev->c1_reset)) {
-+		dev_err(adev->dev, "failed to get ADM0 C1 reset\n");
-+		return PTR_ERR(adev->c1_reset);
-+	}
-+
-+	adev->c2_reset = devm_reset_control_get_exclusive(&pdev->dev, "c2");
-+	if (IS_ERR(adev->c2_reset)) {
-+		dev_err(adev->dev, "failed to get ADM0 C2 reset\n");
-+		return PTR_ERR(adev->c2_reset);
-+	}
-+
-+	ret = clk_prepare_enable(adev->core_clk);
-+	if (ret) {
-+		dev_err(adev->dev, "failed to prepare/enable core clock\n");
-+		return ret;
-+	}
-+
-+	ret = clk_prepare_enable(adev->iface_clk);
-+	if (ret) {
-+		dev_err(adev->dev, "failed to prepare/enable iface clock\n");
-+		goto err_disable_core_clk;
-+	}
-+
-+	reset_control_assert(adev->clk_reset);
-+	reset_control_assert(adev->c0_reset);
-+	reset_control_assert(adev->c1_reset);
-+	reset_control_assert(adev->c2_reset);
-+
-+	udelay(2);
-+
-+	reset_control_deassert(adev->clk_reset);
-+	reset_control_deassert(adev->c0_reset);
-+	reset_control_deassert(adev->c1_reset);
-+	reset_control_deassert(adev->c2_reset);
-+
-+	adev->channels = devm_kcalloc(adev->dev, ADM_MAX_CHANNELS,
-+				      sizeof(*adev->channels), GFP_KERNEL);
-+
-+	if (!adev->channels) {
-+		ret = -ENOMEM;
-+		goto err_disable_clks;
-+	}
-+
-+	/* allocate and initialize channels */
-+	INIT_LIST_HEAD(&adev->common.channels);
-+
-+	for (i = 0; i < ADM_MAX_CHANNELS; i++)
-+		adm_channel_init(adev, &adev->channels[i], i);
-+
-+	/* reset CRCIs */
-+	for (i = 0; i < 16; i++)
-+		writel(ADM_CRCI_CTL_RST, adev->regs +
-+			ADM_CRCI_CTL(i, adev->ee));
-+
-+	/* configure client interfaces */
-+	writel(ADM_CI_RANGE_START(0x40) | ADM_CI_RANGE_END(0xb0) |
-+	       ADM_CI_BURST_8_WORDS, adev->regs + ADM_CI_CONF(0));
-+	writel(ADM_CI_RANGE_START(0x2a) | ADM_CI_RANGE_END(0x2c) |
-+	       ADM_CI_BURST_8_WORDS, adev->regs + ADM_CI_CONF(1));
-+	writel(ADM_CI_RANGE_START(0x12) | ADM_CI_RANGE_END(0x28) |
-+	       ADM_CI_BURST_8_WORDS, adev->regs + ADM_CI_CONF(2));
-+	writel(ADM_GP_CTL_LP_EN | ADM_GP_CTL_LP_CNT(0xf),
-+	       adev->regs + ADM_GP_CTL);
-+
-+	ret = devm_request_irq(adev->dev, adev->irq, adm_dma_irq,
-+			       0, "adm_dma", adev);
-+	if (ret)
-+		goto err_disable_clks;
-+
-+	platform_set_drvdata(pdev, adev);
-+
-+	adev->common.dev = adev->dev;
-+	adev->common.dev->dma_parms = &adev->dma_parms;
-+
-+	/* set capabilities */
-+	dma_cap_zero(adev->common.cap_mask);
-+	dma_cap_set(DMA_SLAVE, adev->common.cap_mask);
-+	dma_cap_set(DMA_PRIVATE, adev->common.cap_mask);
-+
-+	/* initialize dmaengine apis */
-+	adev->common.directions = BIT(DMA_DEV_TO_MEM | DMA_MEM_TO_DEV);
-+	adev->common.residue_granularity = DMA_RESIDUE_GRANULARITY_DESCRIPTOR;
-+	adev->common.src_addr_widths = DMA_SLAVE_BUSWIDTH_4_BYTES;
-+	adev->common.dst_addr_widths = DMA_SLAVE_BUSWIDTH_4_BYTES;
-+	adev->common.device_free_chan_resources = adm_free_chan;
-+	adev->common.device_prep_slave_sg = adm_prep_slave_sg;
-+	adev->common.device_issue_pending = adm_issue_pending;
-+	adev->common.device_tx_status = adm_tx_status;
-+	adev->common.device_terminate_all = adm_terminate_all;
-+	adev->common.device_config = adm_slave_config;
-+
-+	ret = dma_async_device_register(&adev->common);
-+	if (ret) {
-+		dev_err(adev->dev, "failed to register dma async device\n");
-+		goto err_disable_clks;
-+	}
-+
-+	ret = of_dma_controller_register(pdev->dev.of_node,
-+					 of_dma_xlate_by_chan_id,
-+					 &adev->common);
-+	if (ret)
-+		goto err_unregister_dma;
-+
-+	return 0;
-+
-+err_unregister_dma:
-+	dma_async_device_unregister(&adev->common);
-+err_disable_clks:
-+	clk_disable_unprepare(adev->iface_clk);
-+err_disable_core_clk:
-+	clk_disable_unprepare(adev->core_clk);
-+
-+	return ret;
-+}
-+
-+static int adm_dma_remove(struct platform_device *pdev)
-+{
-+	struct adm_device *adev = platform_get_drvdata(pdev);
-+	struct adm_chan *achan;
-+	u32 i;
-+
-+	of_dma_controller_free(pdev->dev.of_node);
-+	dma_async_device_unregister(&adev->common);
-+
-+	for (i = 0; i < ADM_MAX_CHANNELS; i++) {
-+		achan = &adev->channels[i];
-+
-+		/* mask IRQs for this channel/EE pair */
-+		writel(0, adev->regs + ADM_CH_RSLT_CONF(achan->id, adev->ee));
-+
-+		tasklet_kill(&adev->channels[i].vc.task);
-+		adm_terminate_all(&adev->channels[i].vc.chan);
-+	}
-+
-+	devm_free_irq(adev->dev, adev->irq, adev);
-+
-+	clk_disable_unprepare(adev->core_clk);
-+	clk_disable_unprepare(adev->iface_clk);
-+
-+	return 0;
-+}
-+
-+static const struct of_device_id adm_of_match[] = {
-+	{ .compatible = "qcom,adm", },
-+	{}
-+};
-+MODULE_DEVICE_TABLE(of, adm_of_match);
-+
-+static struct platform_driver adm_dma_driver = {
-+	.probe = adm_dma_probe,
-+	.remove = adm_dma_remove,
-+	.driver = {
-+		.name = "adm-dma-engine",
-+		.of_match_table = adm_of_match,
-+	},
-+};
-+
-+module_platform_driver(adm_dma_driver);
-+
-+MODULE_AUTHOR("Andy Gross <agross@codeaurora.org>");
-+MODULE_DESCRIPTION("QCOM ADM DMA engine driver");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/ipq806x/patches-5.15/101-5.12-mtd-parsers-Add-Qcom-SMEM-parser.patch b/target/linux/ipq806x/patches-5.15/101-5.12-mtd-parsers-Add-Qcom-SMEM-parser.patch
deleted file mode 100644
index a78dc82a47..0000000000
--- a/target/linux/ipq806x/patches-5.15/101-5.12-mtd-parsers-Add-Qcom-SMEM-parser.patch
+++ /dev/null
@@ -1,217 +0,0 @@
-From 803eb124e1a64e42888542c3444bfe6dac412c7f Mon Sep 17 00:00:00 2001
-From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-Date: Mon, 4 Jan 2021 09:41:35 +0530
-Subject: mtd: parsers: Add Qcom SMEM parser
-
-NAND based Qualcomm platforms have the partition table populated in the
-Shared Memory (SMEM). Hence, add a parser for parsing the partitions
-from it.
-
-Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
-Link: https://lore.kernel.org/linux-mtd/20210104041137.113075-3-manivannan.sadhasivam@linaro.org
----
- drivers/mtd/parsers/Kconfig        |   8 ++
- drivers/mtd/parsers/Makefile       |   1 +
- drivers/mtd/parsers/qcomsmempart.c | 170 +++++++++++++++++++++++++++++++++++++
- 3 files changed, 179 insertions(+)
- create mode 100644 drivers/mtd/parsers/qcomsmempart.c
-
---- a/drivers/mtd/parsers/Kconfig
-+++ b/drivers/mtd/parsers/Kconfig
-@@ -196,6 +196,14 @@ config MTD_REDBOOT_PARTS_READONLY
- 
- endif # MTD_REDBOOT_PARTS
- 
-+config MTD_QCOMSMEM_PARTS
-+	tristate "Qualcomm SMEM NAND flash partition parser"
-+	depends on MTD_NAND_QCOM || COMPILE_TEST
-+	depends on QCOM_SMEM
-+	help
-+	  This provides support for parsing partitions from Shared Memory (SMEM)
-+	  for NAND flash on Qualcomm platforms.
-+
- config MTD_ROUTERBOOT_PARTS
- 	tristate "RouterBoot flash partition parser"
- 	depends on MTD && OF
---- a/drivers/mtd/parsers/Makefile
-+++ b/drivers/mtd/parsers/Makefile
-@@ -13,4 +13,5 @@ obj-$(CONFIG_MTD_AFS_PARTS)		+= afs.o
- obj-$(CONFIG_MTD_PARSER_TRX)		+= parser_trx.o
- obj-$(CONFIG_MTD_SHARPSL_PARTS)		+= sharpslpart.o
- obj-$(CONFIG_MTD_REDBOOT_PARTS)		+= redboot.o
-+obj-$(CONFIG_MTD_QCOMSMEM_PARTS)	+= qcomsmempart.o
- obj-$(CONFIG_MTD_ROUTERBOOT_PARTS)		+= routerbootpart.o
---- /dev/null
-+++ b/drivers/mtd/parsers/qcomsmempart.c
-@@ -0,0 +1,170 @@
-+// SPDX-License-Identifier: GPL-2.0-only
-+/*
-+ * Qualcomm SMEM NAND flash partition parser
-+ *
-+ * Copyright (C) 2020, Linaro Ltd.
-+ */
-+
-+#include <linux/ctype.h>
-+#include <linux/module.h>
-+#include <linux/mtd/mtd.h>
-+#include <linux/mtd/partitions.h>
-+#include <linux/slab.h>
-+#include <linux/soc/qcom/smem.h>
-+
-+#define SMEM_AARM_PARTITION_TABLE	9
-+#define SMEM_APPS			0
-+
-+#define SMEM_FLASH_PART_MAGIC1		0x55ee73aa
-+#define SMEM_FLASH_PART_MAGIC2		0xe35ebddb
-+#define SMEM_FLASH_PTABLE_V3		3
-+#define SMEM_FLASH_PTABLE_V4		4
-+#define SMEM_FLASH_PTABLE_MAX_PARTS_V3	16
-+#define SMEM_FLASH_PTABLE_MAX_PARTS_V4	48
-+#define SMEM_FLASH_PTABLE_HDR_LEN	(4 * sizeof(u32))
-+#define SMEM_FLASH_PTABLE_NAME_SIZE	16
-+
-+/**
-+ * struct smem_flash_pentry - SMEM Flash partition entry
-+ * @name: Name of the partition
-+ * @offset: Offset in blocks
-+ * @length: Length of the partition in blocks
-+ * @attr: Flags for this partition
-+ */
-+struct smem_flash_pentry {
-+	char name[SMEM_FLASH_PTABLE_NAME_SIZE];
-+	__le32 offset;
-+	__le32 length;
-+	u8 attr;
-+} __packed __aligned(4);
-+
-+/**
-+ * struct smem_flash_ptable - SMEM Flash partition table
-+ * @magic1: Partition table Magic 1
-+ * @magic2: Partition table Magic 2
-+ * @version: Partition table version
-+ * @numparts: Number of partitions in this ptable
-+ * @pentry: Flash partition entries belonging to this ptable
-+ */
-+struct smem_flash_ptable {
-+	__le32 magic1;
-+	__le32 magic2;
-+	__le32 version;
-+	__le32 numparts;
-+	struct smem_flash_pentry pentry[SMEM_FLASH_PTABLE_MAX_PARTS_V4];
-+} __packed __aligned(4);
-+
-+static int parse_qcomsmem_part(struct mtd_info *mtd,
-+			       const struct mtd_partition **pparts,
-+			       struct mtd_part_parser_data *data)
-+{
-+	struct smem_flash_pentry *pentry;
-+	struct smem_flash_ptable *ptable;
-+	size_t len = SMEM_FLASH_PTABLE_HDR_LEN;
-+	struct mtd_partition *parts;
-+	int ret, i, numparts;
-+	char *name, *c;
-+
-+	pr_debug("Parsing partition table info from SMEM\n");
-+	ptable = qcom_smem_get(SMEM_APPS, SMEM_AARM_PARTITION_TABLE, &len);
-+	if (IS_ERR(ptable)) {
-+		pr_err("Error reading partition table header\n");
-+		return PTR_ERR(ptable);
-+	}
-+
-+	/* Verify ptable magic */
-+	if (le32_to_cpu(ptable->magic1) != SMEM_FLASH_PART_MAGIC1 ||
-+	    le32_to_cpu(ptable->magic2) != SMEM_FLASH_PART_MAGIC2) {
-+		pr_err("Partition table magic verification failed\n");
-+		return -EINVAL;
-+	}
-+
-+	/* Ensure that # of partitions is less than the max we have allocated */
-+	numparts = le32_to_cpu(ptable->numparts);
-+	if (numparts > SMEM_FLASH_PTABLE_MAX_PARTS_V4) {
-+		pr_err("Partition numbers exceed the max limit\n");
-+		return -EINVAL;
-+	}
-+
-+	/* Find out length of partition data based on table version */
-+	if (le32_to_cpu(ptable->version) <= SMEM_FLASH_PTABLE_V3) {
-+		len = SMEM_FLASH_PTABLE_HDR_LEN + SMEM_FLASH_PTABLE_MAX_PARTS_V3 *
-+			sizeof(struct smem_flash_pentry);
-+	} else if (le32_to_cpu(ptable->version) == SMEM_FLASH_PTABLE_V4) {
-+		len = SMEM_FLASH_PTABLE_HDR_LEN + SMEM_FLASH_PTABLE_MAX_PARTS_V4 *
-+			sizeof(struct smem_flash_pentry);
-+	} else {
-+		pr_err("Unknown ptable version (%d)", le32_to_cpu(ptable->version));
-+		return -EINVAL;
-+	}
-+
-+	/*
-+	 * Now that the partition table header has been parsed, verified
-+	 * and the length of the partition table calculated, read the
-+	 * complete partition table
-+	 */
-+	ptable = qcom_smem_get(SMEM_APPS, SMEM_AARM_PARTITION_TABLE, &len);
-+	if (IS_ERR_OR_NULL(ptable)) {
-+		pr_err("Error reading partition table\n");
-+		return PTR_ERR(ptable);
-+	}
-+
-+	parts = kcalloc(numparts, sizeof(*parts), GFP_KERNEL);
-+	if (!parts)
-+		return -ENOMEM;
-+
-+	for (i = 0; i < numparts; i++) {
-+		pentry = &ptable->pentry[i];
-+		if (pentry->name[0] == '\0')
-+			continue;
-+
-+		name = kstrdup(pentry->name, GFP_KERNEL);
-+		if (!name) {
-+			ret = -ENOMEM;
-+			goto out_free_parts;
-+		}
-+
-+		/* Convert name to lower case */
-+		for (c = name; *c != '\0'; c++)
-+			*c = tolower(*c);
-+
-+		parts[i].name = name;
-+		parts[i].offset = le32_to_cpu(pentry->offset) * mtd->erasesize;
-+		parts[i].mask_flags = pentry->attr;
-+		parts[i].size = le32_to_cpu(pentry->length) * mtd->erasesize;
-+		pr_debug("%d: %s offs=0x%08x size=0x%08x attr:0x%08x\n",
-+			 i, pentry->name, le32_to_cpu(pentry->offset),
-+			 le32_to_cpu(pentry->length), pentry->attr);
-+	}
-+
-+	pr_debug("SMEM partition table found: ver: %d len: %d\n",
-+		 le32_to_cpu(ptable->version), numparts);
-+	*pparts = parts;
-+
-+	return numparts;
-+
-+out_free_parts:
-+	while (--i >= 0)
-+		kfree(parts[i].name);
-+	kfree(parts);
-+	*pparts = NULL;
-+
-+	return ret;
-+}
-+
-+static const struct of_device_id qcomsmem_of_match_table[] = {
-+	{ .compatible = "qcom,smem-part" },
-+	{},
-+};
-+MODULE_DEVICE_TABLE(of, qcomsmem_of_match_table);
-+
-+static struct mtd_part_parser mtd_parser_qcomsmem = {
-+	.parse_fn = parse_qcomsmem_part,
-+	.name = "qcomsmem",
-+	.of_match_table = qcomsmem_of_match_table,
-+};
-+module_mtd_part_parser(mtd_parser_qcomsmem);
-+
-+MODULE_LICENSE("GPL v2");
-+MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>");
-+MODULE_DESCRIPTION("Qualcomm SMEM NAND flash partition parser");
diff --git a/target/linux/ipq806x/patches-5.15/104-1-drivers-thermal-tsens-Add-VER_0-tsens-version.patch b/target/linux/ipq806x/patches-5.15/104-1-drivers-thermal-tsens-Add-VER_0-tsens-version.patch
deleted file mode 100644
index 8627244c59..0000000000
--- a/target/linux/ipq806x/patches-5.15/104-1-drivers-thermal-tsens-Add-VER_0-tsens-version.patch
+++ /dev/null
@@ -1,285 +0,0 @@
-From 5c7d1181056feef0b58fb2f556f55e170ba5b479 Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Sat, 25 Jul 2020 19:14:59 +0200
-Subject: [PATCH 01/10] drivers: thermal: tsens: Add VER_0 tsens version
-
-VER_0 is used to describe device based on tsens version before v0.1.
-These device are devices based on msm8960 for example apq8064 or
-ipq806x.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
-Reported-by: kernel test robot <lkp@intel.com>
-Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
----
- drivers/thermal/qcom/tsens.c | 150 ++++++++++++++++++++++++++++-------
- drivers/thermal/qcom/tsens.h |   4 +-
- 2 files changed, 124 insertions(+), 30 deletions(-)
-
---- a/drivers/thermal/qcom/tsens.c
-+++ b/drivers/thermal/qcom/tsens.c
-@@ -12,6 +12,7 @@
- #include <linux/of.h>
- #include <linux/of_address.h>
- #include <linux/of_platform.h>
-+#include <linux/mfd/syscon.h>
- #include <linux/platform_device.h>
- #include <linux/pm.h>
- #include <linux/regmap.h>
-@@ -515,6 +516,15 @@ static irqreturn_t tsens_irq_thread(int
- 			dev_dbg(priv->dev, "[%u] %s: no violation:  %d\n",
- 				hw_id, __func__, temp);
- 		}
-+
-+		if (tsens_version(priv) < VER_0_1) {
-+			/* Constraint: There is only 1 interrupt control register for all
-+			 * 11 temperature sensor. So monitoring more than 1 sensor based
-+			 * on interrupts will yield inconsistent result. To overcome this
-+			 * issue we will monitor only sensor 0 which is the master sensor.
-+			 */
-+			break;
-+		}
- 	}
- 
- 	return IRQ_HANDLED;
-@@ -530,6 +540,13 @@ static int tsens_set_trips(void *_sensor
- 	int high_val, low_val, cl_high, cl_low;
- 	u32 hw_id = s->hw_id;
- 
-+	if (tsens_version(priv) < VER_0_1) {
-+		/* Pre v0.1 IP had a single register for each type of interrupt
-+		 * and thresholds
-+		 */
-+		hw_id = 0;
-+	}
-+
- 	dev_dbg(dev, "[%u] %s: proposed thresholds: (%d:%d)\n",
- 		hw_id, __func__, low, high);
- 
-@@ -584,18 +601,21 @@ int get_temp_tsens_valid(const struct ts
- 	u32 valid;
- 	int ret;
- 
--	ret = regmap_field_read(priv->rf[valid_idx], &valid);
--	if (ret)
--		return ret;
--	while (!valid) {
--		/* Valid bit is 0 for 6 AHB clock cycles.
--		 * At 19.2MHz, 1 AHB clock is ~60ns.
--		 * We should enter this loop very, very rarely.
--		 */
--		ndelay(400);
-+	/* VER_0 doesn't have VALID bit */
-+	if (tsens_version(priv) >= VER_0_1) {
- 		ret = regmap_field_read(priv->rf[valid_idx], &valid);
- 		if (ret)
- 			return ret;
-+		while (!valid) {
-+			/* Valid bit is 0 for 6 AHB clock cycles.
-+			 * At 19.2MHz, 1 AHB clock is ~60ns.
-+			 * We should enter this loop very, very rarely.
-+			 */
-+			ndelay(400);
-+			ret = regmap_field_read(priv->rf[valid_idx], &valid);
-+			if (ret)
-+				return ret;
-+		}
- 	}
- 
- 	/* Valid bit is set, OK to read the temperature */
-@@ -608,15 +628,29 @@ int get_temp_common(const struct tsens_s
- {
- 	struct tsens_priv *priv = s->priv;
- 	int hw_id = s->hw_id;
--	int last_temp = 0, ret;
-+	int last_temp = 0, ret, trdy;
-+	unsigned long timeout;
- 
--	ret = regmap_field_read(priv->rf[LAST_TEMP_0 + hw_id], &last_temp);
--	if (ret)
--		return ret;
-+	timeout = jiffies + usecs_to_jiffies(TIMEOUT_US);
-+	do {
-+		if (tsens_version(priv) == VER_0) {
-+			ret = regmap_field_read(priv->rf[TRDY], &trdy);
-+			if (ret)
-+				return ret;
-+			if (!trdy)
-+				continue;
-+		}
- 
--	*temp = code_to_degc(last_temp, s) * 1000;
-+		ret = regmap_field_read(priv->rf[LAST_TEMP_0 + hw_id], &last_temp);
-+		if (ret)
-+			return ret;
- 
--	return 0;
-+		*temp = code_to_degc(last_temp, s) * 1000;
-+
-+		return 0;
-+	} while (time_before(jiffies, timeout));
-+
-+	return -ETIMEDOUT;
- }
- 
- #ifdef CONFIG_DEBUG_FS
-@@ -738,19 +772,34 @@ int __init init_common(struct tsens_priv
- 		priv->tm_offset = 0x1000;
- 	}
- 
--	res = platform_get_resource(op, IORESOURCE_MEM, 0);
--	tm_base = devm_ioremap_resource(dev, res);
--	if (IS_ERR(tm_base)) {
--		ret = PTR_ERR(tm_base);
--		goto err_put_device;
-+	if (tsens_version(priv) >= VER_0_1) {
-+		res = platform_get_resource(op, IORESOURCE_MEM, 0);
-+		tm_base = devm_ioremap_resource(dev, res);
-+		if (IS_ERR(tm_base)) {
-+			ret = PTR_ERR(tm_base);
-+			goto err_put_device;
-+		}
-+
-+		priv->tm_map = devm_regmap_init_mmio(dev, tm_base, &tsens_config);
-+	} else { /* VER_0 share the same gcc regs using a syscon */
-+		struct device *parent = priv->dev->parent;
-+
-+		if (parent)
-+			priv->tm_map = syscon_node_to_regmap(parent->of_node);
- 	}
- 
--	priv->tm_map = devm_regmap_init_mmio(dev, tm_base, &tsens_config);
--	if (IS_ERR(priv->tm_map)) {
--		ret = PTR_ERR(priv->tm_map);
-+	if (IS_ERR_OR_NULL(priv->tm_map)) {
-+		if (!priv->tm_map)
-+			ret = -ENODEV;
-+		else
-+			ret = PTR_ERR(priv->tm_map);
- 		goto err_put_device;
- 	}
- 
-+	/* VER_0 have only tm_map */
-+	if (!priv->srot_map)
-+		priv->srot_map = priv->tm_map;
-+
- 	if (tsens_version(priv) > VER_0_1) {
- 		for (i = VER_MAJOR; i <= VER_STEP; i++) {
- 			priv->rf[i] = devm_regmap_field_alloc(dev, priv->srot_map,
-@@ -771,6 +820,10 @@ int __init init_common(struct tsens_priv
- 		ret = PTR_ERR(priv->rf[TSENS_EN]);
- 		goto err_put_device;
- 	}
-+	/* in VER_0 TSENS need to be explicitly enabled */
-+	if (tsens_version(priv) == VER_0)
-+		regmap_field_write(priv->rf[TSENS_EN], 1);
-+
- 	ret = regmap_field_read(priv->rf[TSENS_EN], &enabled);
- 	if (ret)
- 		goto err_put_device;
-@@ -793,6 +846,19 @@ int __init init_common(struct tsens_priv
- 		goto err_put_device;
- 	}
- 
-+	priv->rf[TSENS_SW_RST] =
-+		devm_regmap_field_alloc(dev, priv->srot_map, priv->fields[TSENS_SW_RST]);
-+	if (IS_ERR(priv->rf[TSENS_SW_RST])) {
-+		ret = PTR_ERR(priv->rf[TSENS_SW_RST]);
-+		goto err_put_device;
-+	}
-+
-+	priv->rf[TRDY] = devm_regmap_field_alloc(dev, priv->tm_map, priv->fields[TRDY]);
-+	if (IS_ERR(priv->rf[TRDY])) {
-+		ret = PTR_ERR(priv->rf[TRDY]);
-+		goto err_put_device;
-+	}
-+
- 	/* This loop might need changes if enum regfield_ids is reordered */
- 	for (j = LAST_TEMP_0; j <= UP_THRESH_15; j += 16) {
- 		for (i = 0; i < priv->feat->max_sensors; i++) {
-@@ -808,7 +874,7 @@ int __init init_common(struct tsens_priv
- 		}
- 	}
- 
--	if (priv->feat->crit_int) {
-+	if (priv->feat->crit_int || tsens_version(priv) < VER_0_1) {
- 		/* Loop might need changes if enum regfield_ids is reordered */
- 		for (j = CRITICAL_STATUS_0; j <= CRIT_THRESH_15; j += 16) {
- 			for (i = 0; i < priv->feat->max_sensors; i++) {
-@@ -846,7 +912,11 @@ int __init init_common(struct tsens_priv
- 	}
- 
- 	spin_lock_init(&priv->ul_lock);
--	tsens_enable_irq(priv);
-+
-+	/* VER_0 interrupt doesn't need to be enabled */
-+	if (tsens_version(priv) >= VER_0_1)
-+		tsens_enable_irq(priv);
-+
- 	tsens_debug_init(op);
- 
- err_put_device:
-@@ -945,10 +1015,19 @@ static int tsens_register_irq(struct tse
- 		if (irq == -ENXIO)
- 			ret = 0;
- 	} else {
--		ret = devm_request_threaded_irq(&pdev->dev, irq,
--						NULL, thread_fn,
--						IRQF_ONESHOT,
--						dev_name(&pdev->dev), priv);
-+		/* VER_0 interrupt is TRIGGER_RISING, VER_0_1 and up is ONESHOT */
-+		if (tsens_version(priv) == VER_0)
-+			ret = devm_request_threaded_irq(&pdev->dev, irq,
-+							thread_fn, NULL,
-+							IRQF_TRIGGER_RISING,
-+							dev_name(&pdev->dev),
-+							priv);
-+		else
-+			ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
-+							thread_fn, IRQF_ONESHOT,
-+							dev_name(&pdev->dev),
-+							priv);
-+
- 		if (ret)
- 			dev_err(&pdev->dev, "%s: failed to get irq\n",
- 				__func__);
-@@ -977,6 +1056,19 @@ static int tsens_register(struct tsens_p
- 			priv->ops->enable(priv, i);
- 	}
- 
-+	/* VER_0 require to set MIN and MAX THRESH
-+	 * These 2 regs are set using the:
-+	 * - CRIT_THRESH_0 for MAX THRESH hardcoded to 120°C
-+	 * - CRIT_THRESH_1 for MIN THRESH hardcoded to   0°C
-+	 */
-+	if (tsens_version(priv) < VER_0_1) {
-+		regmap_field_write(priv->rf[CRIT_THRESH_0],
-+				   tsens_mC_to_hw(priv->sensor, 120000));
-+
-+		regmap_field_write(priv->rf[CRIT_THRESH_1],
-+				   tsens_mC_to_hw(priv->sensor, 0));
-+	}
-+
- 	ret = tsens_register_irq(priv, "uplow", tsens_irq_thread);
- 	if (ret < 0)
- 		return ret;
---- a/drivers/thermal/qcom/tsens.h
-+++ b/drivers/thermal/qcom/tsens.h
-@@ -13,6 +13,7 @@
- #define CAL_DEGC_PT2		120
- #define SLOPE_FACTOR		1000
- #define SLOPE_DEFAULT		3200
-+#define TIMEOUT_US		100
- #define THRESHOLD_MAX_ADC_CODE	0x3ff
- #define THRESHOLD_MIN_ADC_CODE	0x0
- 
-@@ -25,7 +26,8 @@ struct tsens_priv;
- 
- /* IP version numbers in ascending order */
- enum tsens_ver {
--	VER_0_1 = 0,
-+	VER_0 = 0,
-+	VER_0_1,
- 	VER_1_X,
- 	VER_2_X,
- };
diff --git a/target/linux/ipq806x/patches-5.15/104-2-drivers-thermal-tsens-Don-t-hardcode-sensor-slope.patch b/target/linux/ipq806x/patches-5.15/104-2-drivers-thermal-tsens-Don-t-hardcode-sensor-slope.patch
deleted file mode 100644
index 109f524bbd..0000000000
--- a/target/linux/ipq806x/patches-5.15/104-2-drivers-thermal-tsens-Don-t-hardcode-sensor-slope.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From efa0d50a6c5ec7619371dfe4d3e6ca54b73787d5 Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Wed, 25 Nov 2020 16:47:21 +0100
-Subject: [PATCH 02/10] drivers: thermal: tsens: Don't hardcode sensor slope
-
-Function compute_intercept_slope hardcode the sensor slope to
-SLOPE_DEFAULT. Change this and use the default value only if a slope is
-not defined. This is needed for tsens VER_0 that has a hardcoded slope
-table.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
----
- drivers/thermal/qcom/tsens.c | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/drivers/thermal/qcom/tsens.c
-+++ b/drivers/thermal/qcom/tsens.c
-@@ -86,7 +86,8 @@ void compute_intercept_slope(struct tsen
- 			"%s: sensor%d - data_point1:%#x data_point2:%#x\n",
- 			__func__, i, p1[i], p2[i]);
- 
--		priv->sensor[i].slope = SLOPE_DEFAULT;
-+		if (!priv->sensor[i].slope)
-+			priv->sensor[i].slope = SLOPE_DEFAULT;
- 		if (mode == TWO_PT_CALIB) {
- 			/*
- 			 * slope (m) = adc_code2 - adc_code1 (y2 - y1)/
diff --git a/target/linux/ipq806x/patches-5.15/104-3-drivers-thermal-tsens-Convert-msm8960-to-reg_field.patch b/target/linux/ipq806x/patches-5.15/104-3-drivers-thermal-tsens-Convert-msm8960-to-reg_field.patch
deleted file mode 100644
index bf378107c6..0000000000
--- a/target/linux/ipq806x/patches-5.15/104-3-drivers-thermal-tsens-Convert-msm8960-to-reg_field.patch
+++ /dev/null
@@ -1,119 +0,0 @@
-From 6bac2e2fa36c2d7c304768a689d8b73155b90aa2 Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Wed, 25 Nov 2020 17:15:51 +0100
-Subject: [PATCH 03/10] drivers: thermal: tsens: Convert msm8960 to reg_field
-
-Convert msm9860 driver to reg_field to use the init_common
-function.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
----
- drivers/thermal/qcom/tsens-8960.c | 80 ++++++++++++++++++++++++++++++-
- 1 file changed, 79 insertions(+), 1 deletion(-)
-
---- a/drivers/thermal/qcom/tsens-8960.c
-+++ b/drivers/thermal/qcom/tsens-8960.c
-@@ -51,11 +51,22 @@
- #define MIN_LIMIT_TH		0x0
- #define MAX_LIMIT_TH		0xff
- 
--#define S0_STATUS_ADDR		0x3628
- #define INT_STATUS_ADDR		0x363c
- #define TRDY_MASK		BIT(7)
- #define TIMEOUT_US		100
- 
-+#define S0_STATUS_OFF		0x3628
-+#define S1_STATUS_OFF		0x362c
-+#define S2_STATUS_OFF		0x3630
-+#define S3_STATUS_OFF		0x3634
-+#define S4_STATUS_OFF		0x3638
-+#define S5_STATUS_OFF		0x3664  /* Sensors 5-10 found on apq8064/msm8960 */
-+#define S6_STATUS_OFF		0x3668
-+#define S7_STATUS_OFF		0x366c
-+#define S8_STATUS_OFF		0x3670
-+#define S9_STATUS_OFF		0x3674
-+#define S10_STATUS_OFF		0x3678
-+
- static int suspend_8960(struct tsens_priv *priv)
- {
- 	int ret;
-@@ -269,6 +280,71 @@ static int get_temp_8960(const struct ts
- 	return -ETIMEDOUT;
- }
- 
-+static struct tsens_features tsens_8960_feat = {
-+	.ver_major	= VER_0,
-+	.crit_int	= 0,
-+	.adc		= 1,
-+	.srot_split	= 0,
-+	.max_sensors	= 11,
-+};
-+
-+static const struct reg_field tsens_8960_regfields[MAX_REGFIELDS] = {
-+	/* ----- SROT ------ */
-+	/* No VERSION information */
-+
-+	/* CNTL */
-+	[TSENS_EN]     = REG_FIELD(CNTL_ADDR,  0, 0),
-+	[TSENS_SW_RST] = REG_FIELD(CNTL_ADDR,  1, 1),
-+	/* 8960 has 5 sensors, 8660 has 11, we only handle 5 */
-+	[SENSOR_EN]    = REG_FIELD(CNTL_ADDR,  3, 7),
-+
-+	/* ----- TM ------ */
-+	/* INTERRUPT ENABLE */
-+	/* NO INTERRUPT ENABLE */
-+
-+	/* Single UPPER/LOWER TEMPERATURE THRESHOLD for all sensors */
-+	[LOW_THRESH_0]   = REG_FIELD(THRESHOLD_ADDR,  0,  7),
-+	[UP_THRESH_0]    = REG_FIELD(THRESHOLD_ADDR,  8, 15),
-+	/* MIN_THRESH_0 and MAX_THRESH_0 are not present in the regfield
-+	 * Recycle CRIT_THRESH_0 and 1 to set the required regs to hardcoded temp
-+	 * MIN_THRESH_0 -> CRIT_THRESH_1
-+	 * MAX_THRESH_0 -> CRIT_THRESH_0
-+	 */
-+	[CRIT_THRESH_1]   = REG_FIELD(THRESHOLD_ADDR, 16, 23),
-+	[CRIT_THRESH_0]   = REG_FIELD(THRESHOLD_ADDR, 24, 31),
-+
-+	/* UPPER/LOWER INTERRUPT [CLEAR/STATUS] */
-+	/* 1 == clear, 0 == normal operation */
-+	[LOW_INT_CLEAR_0]   = REG_FIELD(CNTL_ADDR,  9,  9),
-+	[UP_INT_CLEAR_0]    = REG_FIELD(CNTL_ADDR, 10, 10),
-+
-+	/* NO CRITICAL INTERRUPT SUPPORT on 8960 */
-+
-+	/* Sn_STATUS */
-+	[LAST_TEMP_0]  = REG_FIELD(S0_STATUS_OFF,  0,  7),
-+	[LAST_TEMP_1]  = REG_FIELD(S1_STATUS_OFF,  0,  7),
-+	[LAST_TEMP_2]  = REG_FIELD(S2_STATUS_OFF,  0,  7),
-+	[LAST_TEMP_3]  = REG_FIELD(S3_STATUS_OFF,  0,  7),
-+	[LAST_TEMP_4]  = REG_FIELD(S4_STATUS_OFF,  0,  7),
-+	[LAST_TEMP_5]  = REG_FIELD(S5_STATUS_OFF,  0,  7),
-+	[LAST_TEMP_6]  = REG_FIELD(S6_STATUS_OFF,  0,  7),
-+	[LAST_TEMP_7]  = REG_FIELD(S7_STATUS_OFF,  0,  7),
-+	[LAST_TEMP_8]  = REG_FIELD(S8_STATUS_OFF,  0,  7),
-+	[LAST_TEMP_9]  = REG_FIELD(S9_STATUS_OFF,  0,  7),
-+	[LAST_TEMP_10] = REG_FIELD(S10_STATUS_OFF, 0,  7),
-+
-+	/* No VALID field on 8960 */
-+	/* TSENS_INT_STATUS bits: 1 == threshold violated */
-+	[MIN_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 0, 0),
-+	[LOWER_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 1, 1),
-+	[UPPER_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 2, 2),
-+	/* No CRITICAL field on 8960 */
-+	[MAX_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 3, 3),
-+
-+	/* TRDY: 1=ready, 0=in progress */
-+	[TRDY] = REG_FIELD(INT_STATUS_ADDR, 7, 7),
-+};
-+
- static const struct tsens_ops ops_8960 = {
- 	.init		= init_8960,
- 	.calibrate	= calibrate_8960,
-@@ -282,4 +358,6 @@ static const struct tsens_ops ops_8960 =
- struct tsens_plat_data data_8960 = {
- 	.num_sensors	= 11,
- 	.ops		= &ops_8960,
-+	.feat		= &tsens_8960_feat,
-+	.fields		= tsens_8960_regfields,
- };
diff --git a/target/linux/ipq806x/patches-5.15/104-4-drivers-thermal-tsens-Use-init_common-for-msm8960.patch b/target/linux/ipq806x/patches-5.15/104-4-drivers-thermal-tsens-Use-init_common-for-msm8960.patch
deleted file mode 100644
index ae8a52c100..0000000000
--- a/target/linux/ipq806x/patches-5.15/104-4-drivers-thermal-tsens-Use-init_common-for-msm8960.patch
+++ /dev/null
@@ -1,81 +0,0 @@
-From c04f98a496929f75d75c65115d5717423c3d0634 Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Wed, 25 Nov 2020 17:16:36 +0100
-Subject: [PATCH 04/10] drivers: thermal: tsens: Use init_common for msm8960
-
-Use init_common and drop custom init for msm8960.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
----
- drivers/thermal/qcom/tsens-8960.c | 52 +------------------------------
- 1 file changed, 1 insertion(+), 51 deletions(-)
-
---- a/drivers/thermal/qcom/tsens-8960.c
-+++ b/drivers/thermal/qcom/tsens-8960.c
-@@ -173,56 +173,6 @@ static void disable_8960(struct tsens_pr
- 	regmap_write(priv->tm_map, CNTL_ADDR, reg_cntl);
- }
- 
--static int init_8960(struct tsens_priv *priv)
--{
--	int ret, i;
--	u32 reg_cntl;
--
--	priv->tm_map = dev_get_regmap(priv->dev, NULL);
--	if (!priv->tm_map)
--		return -ENODEV;
--
--	/*
--	 * The status registers for each sensor are discontiguous
--	 * because some SoCs have 5 sensors while others have more
--	 * but the control registers stay in the same place, i.e
--	 * directly after the first 5 status registers.
--	 */
--	for (i = 0; i < priv->num_sensors; i++) {
--		if (i >= 5)
--			priv->sensor[i].status = S0_STATUS_ADDR + 40;
--		priv->sensor[i].status += i * 4;
--	}
--
--	reg_cntl = SW_RST;
--	ret = regmap_update_bits(priv->tm_map, CNTL_ADDR, SW_RST, reg_cntl);
--	if (ret)
--		return ret;
--
--	if (priv->num_sensors > 1) {
--		reg_cntl |= SLP_CLK_ENA | (MEASURE_PERIOD << 18);
--		reg_cntl &= ~SW_RST;
--		ret = regmap_update_bits(priv->tm_map, CONFIG_ADDR,
--					 CONFIG_MASK, CONFIG);
--	} else {
--		reg_cntl |= SLP_CLK_ENA_8660 | (MEASURE_PERIOD << 16);
--		reg_cntl &= ~CONFIG_MASK_8660;
--		reg_cntl |= CONFIG_8660 << CONFIG_SHIFT_8660;
--	}
--
--	reg_cntl |= GENMASK(priv->num_sensors - 1, 0) << SENSOR0_SHIFT;
--	ret = regmap_write(priv->tm_map, CNTL_ADDR, reg_cntl);
--	if (ret)
--		return ret;
--
--	reg_cntl |= EN;
--	ret = regmap_write(priv->tm_map, CNTL_ADDR, reg_cntl);
--	if (ret)
--		return ret;
--
--	return 0;
--}
--
- static int calibrate_8960(struct tsens_priv *priv)
- {
- 	int i;
-@@ -346,7 +296,7 @@ static const struct reg_field tsens_8960
- };
- 
- static const struct tsens_ops ops_8960 = {
--	.init		= init_8960,
-+	.init		= init_common,
- 	.calibrate	= calibrate_8960,
- 	.get_temp	= get_temp_8960,
- 	.enable		= enable_8960,
diff --git a/target/linux/ipq806x/patches-5.15/104-5-drivers-thermal-tsens-Fix-bug-in-sensor-enable-for-m.patch b/target/linux/ipq806x/patches-5.15/104-5-drivers-thermal-tsens-Fix-bug-in-sensor-enable-for-m.patch
deleted file mode 100644
index 7b01a67d90..0000000000
--- a/target/linux/ipq806x/patches-5.15/104-5-drivers-thermal-tsens-Fix-bug-in-sensor-enable-for-m.patch
+++ /dev/null
@@ -1,66 +0,0 @@
-From b3e8bd33b84a6b6c863bd1733bd15b5f1483b8ab Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Wed, 25 Nov 2020 17:06:55 +0100
-Subject: [PATCH 05/10] drivers: thermal: tsens: Fix bug in sensor enable for
- msm8960
-
-Device based on tsens VER_0 contains a hardware bug that results in some
-problem with sensor enablement. Sensor id 6-11 can't be enabled
-selectively and all of them must be enabled in one step.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
----
- drivers/thermal/qcom/tsens-8960.c | 23 ++++++++++++++++++++---
- 1 file changed, 20 insertions(+), 3 deletions(-)
-
---- a/drivers/thermal/qcom/tsens-8960.c
-+++ b/drivers/thermal/qcom/tsens-8960.c
-@@ -27,9 +27,9 @@
- #define EN			BIT(0)
- #define SW_RST			BIT(1)
- #define SENSOR0_EN		BIT(3)
-+#define MEASURE_PERIOD		BIT(18)
- #define SLP_CLK_ENA		BIT(26)
- #define SLP_CLK_ENA_8660	BIT(24)
--#define MEASURE_PERIOD		1
- #define SENSOR0_SHIFT		3
- 
- /* INT_STATUS_ADDR bitmasks */
-@@ -126,17 +126,34 @@ static int resume_8960(struct tsens_priv
- static int enable_8960(struct tsens_priv *priv, int id)
- {
- 	int ret;
--	u32 reg, mask;
-+	u32 reg, mask = BIT(id);
- 
- 	ret = regmap_read(priv->tm_map, CNTL_ADDR, &reg);
- 	if (ret)
- 		return ret;
- 
--	mask = BIT(id + SENSOR0_SHIFT);
-+	/* HARDWARE BUG:
-+	 * On platforms with more than 6 sensors, all remaining sensors
-+	 * must be enabled together, otherwise undefined results are expected.
-+	 * (Sensor 6-7 disabled, Sensor 3 disabled...) In the original driver,
-+	 * all the sensors are enabled in one step hence this bug is not
-+	 * triggered.
-+	 */
-+	if (id > 5)
-+		mask = GENMASK(10, 6);
-+
-+	mask <<= SENSOR0_SHIFT;
-+
-+	/* Sensors already enabled. Skip. */
-+	if ((reg & mask) == mask)
-+		return 0;
-+
- 	ret = regmap_write(priv->tm_map, CNTL_ADDR, reg | SW_RST);
- 	if (ret)
- 		return ret;
- 
-+	reg |= MEASURE_PERIOD;
-+
- 	if (priv->num_sensors > 1)
- 		reg |= mask | SLP_CLK_ENA | EN;
- 	else
diff --git a/target/linux/ipq806x/patches-5.15/104-6-drivers-thermal-tsens-Replace-custom-8960-apis-with-.patch b/target/linux/ipq806x/patches-5.15/104-6-drivers-thermal-tsens-Replace-custom-8960-apis-with-.patch
deleted file mode 100644
index a82f596954..0000000000
--- a/target/linux/ipq806x/patches-5.15/104-6-drivers-thermal-tsens-Replace-custom-8960-apis-with-.patch
+++ /dev/null
@@ -1,109 +0,0 @@
-From 1ff9f982051759e0387e8c7e793b49c48eae291d Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Wed, 25 Nov 2020 17:11:05 +0100
-Subject: [PATCH 06/10] drivers: thermal: tsens: Replace custom 8960 apis with
- generic apis
-
-Rework calibrate function to use common function. Derive the offset from
-a missing hardcoded slope table and the data from the nvmem calib
-efuses.
-Drop custom get_temp function and use generic api.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
----
- drivers/thermal/qcom/tsens-8960.c | 56 +++++++++----------------------
- 1 file changed, 15 insertions(+), 41 deletions(-)
-
---- a/drivers/thermal/qcom/tsens-8960.c
-+++ b/drivers/thermal/qcom/tsens-8960.c
-@@ -67,6 +67,13 @@
- #define S9_STATUS_OFF		0x3674
- #define S10_STATUS_OFF		0x3678
- 
-+/* Original slope - 200 to compensate mC to C inaccuracy */
-+static u32 tsens_msm8960_slope[] = {
-+			976, 976, 954, 976,
-+			911, 932, 932, 999,
-+			932, 999, 932
-+			};
-+
- static int suspend_8960(struct tsens_priv *priv)
- {
- 	int ret;
-@@ -194,9 +201,7 @@ static int calibrate_8960(struct tsens_p
- {
- 	int i;
- 	char *data;
--
--	ssize_t num_read = priv->num_sensors;
--	struct tsens_sensor *s = priv->sensor;
-+	u32 p1[11];
- 
- 	data = qfprom_read(priv->dev, "calib");
- 	if (IS_ERR(data))
-@@ -204,49 +209,18 @@ static int calibrate_8960(struct tsens_p
- 	if (IS_ERR(data))
- 		return PTR_ERR(data);
- 
--	for (i = 0; i < num_read; i++, s++)
--		s->offset = data[i];
-+	for (i = 0; i < priv->num_sensors; i++) {
-+		p1[i] = data[i];
-+		priv->sensor[i].slope = tsens_msm8960_slope[i];
-+	}
-+
-+	compute_intercept_slope(priv, p1, NULL, ONE_PT_CALIB);
- 
- 	kfree(data);
- 
- 	return 0;
- }
- 
--/* Temperature on y axis and ADC-code on x-axis */
--static inline int code_to_mdegC(u32 adc_code, const struct tsens_sensor *s)
--{
--	int slope, offset;
--
--	slope = thermal_zone_get_slope(s->tzd);
--	offset = CAL_MDEGC - slope * s->offset;
--
--	return adc_code * slope + offset;
--}
--
--static int get_temp_8960(const struct tsens_sensor *s, int *temp)
--{
--	int ret;
--	u32 code, trdy;
--	struct tsens_priv *priv = s->priv;
--	unsigned long timeout;
--
--	timeout = jiffies + usecs_to_jiffies(TIMEOUT_US);
--	do {
--		ret = regmap_read(priv->tm_map, INT_STATUS_ADDR, &trdy);
--		if (ret)
--			return ret;
--		if (!(trdy & TRDY_MASK))
--			continue;
--		ret = regmap_read(priv->tm_map, s->status, &code);
--		if (ret)
--			return ret;
--		*temp = code_to_mdegC(code, s);
--		return 0;
--	} while (time_before(jiffies, timeout));
--
--	return -ETIMEDOUT;
--}
--
- static struct tsens_features tsens_8960_feat = {
- 	.ver_major	= VER_0,
- 	.crit_int	= 0,
-@@ -315,7 +289,7 @@ static const struct reg_field tsens_8960
- static const struct tsens_ops ops_8960 = {
- 	.init		= init_common,
- 	.calibrate	= calibrate_8960,
--	.get_temp	= get_temp_8960,
-+	.get_temp	= get_temp_common,
- 	.enable		= enable_8960,
- 	.disable	= disable_8960,
- 	.suspend	= suspend_8960,
diff --git a/target/linux/ipq806x/patches-5.15/104-7-drivers-thermal-tsens-Drop-unused-define-for-msm8960.patch b/target/linux/ipq806x/patches-5.15/104-7-drivers-thermal-tsens-Drop-unused-define-for-msm8960.patch
deleted file mode 100644
index 77ca3cfe45..0000000000
--- a/target/linux/ipq806x/patches-5.15/104-7-drivers-thermal-tsens-Drop-unused-define-for-msm8960.patch
+++ /dev/null
@@ -1,65 +0,0 @@
-From 5716a61239c6ac9ceb137e825e93c3aea06c4634 Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Fri, 19 Mar 2021 00:48:23 +0100
-Subject: [PATCH 07/10] drivers: thermal: tsens: Drop unused define for msm8960
-
-Drop unused define for msm8960 replaced by generic api and reg_field.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
----
- drivers/thermal/qcom/tsens-8960.c | 24 +-----------------------
- 1 file changed, 1 insertion(+), 23 deletions(-)
-
---- a/drivers/thermal/qcom/tsens-8960.c
-+++ b/drivers/thermal/qcom/tsens-8960.c
-@@ -10,8 +10,6 @@
- #include <linux/thermal.h>
- #include "tsens.h"
- 
--#define CAL_MDEGC		30000
--
- #define CONFIG_ADDR		0x3640
- #define CONFIG_ADDR_8660	0x3620
- /* CONFIG_ADDR bitmasks */
-@@ -21,39 +19,19 @@
- #define CONFIG_SHIFT_8660	28
- #define CONFIG_MASK_8660	(3 << CONFIG_SHIFT_8660)
- 
--#define STATUS_CNTL_ADDR_8064	0x3660
- #define CNTL_ADDR		0x3620
- /* CNTL_ADDR bitmasks */
- #define EN			BIT(0)
- #define SW_RST			BIT(1)
--#define SENSOR0_EN		BIT(3)
-+
- #define MEASURE_PERIOD		BIT(18)
- #define SLP_CLK_ENA		BIT(26)
- #define SLP_CLK_ENA_8660	BIT(24)
- #define SENSOR0_SHIFT		3
- 
--/* INT_STATUS_ADDR bitmasks */
--#define MIN_STATUS_MASK		BIT(0)
--#define LOWER_STATUS_CLR	BIT(1)
--#define UPPER_STATUS_CLR	BIT(2)
--#define MAX_STATUS_MASK		BIT(3)
--
- #define THRESHOLD_ADDR		0x3624
--/* THRESHOLD_ADDR bitmasks */
--#define THRESHOLD_MAX_LIMIT_SHIFT	24
--#define THRESHOLD_MIN_LIMIT_SHIFT	16
--#define THRESHOLD_UPPER_LIMIT_SHIFT	8
--#define THRESHOLD_LOWER_LIMIT_SHIFT	0
--
--/* Initial temperature threshold values */
--#define LOWER_LIMIT_TH		0x50
--#define UPPER_LIMIT_TH		0xdf
--#define MIN_LIMIT_TH		0x0
--#define MAX_LIMIT_TH		0xff
- 
- #define INT_STATUS_ADDR		0x363c
--#define TRDY_MASK		BIT(7)
--#define TIMEOUT_US		100
- 
- #define S0_STATUS_OFF		0x3628
- #define S1_STATUS_OFF		0x362c
diff --git a/target/linux/ipq806x/patches-5.15/104-8-drivers-thermal-tsens-Add-support-for-ipq8064-tsens.patch b/target/linux/ipq806x/patches-5.15/104-8-drivers-thermal-tsens-Add-support-for-ipq8064-tsens.patch
deleted file mode 100644
index 127abaefc3..0000000000
--- a/target/linux/ipq806x/patches-5.15/104-8-drivers-thermal-tsens-Add-support-for-ipq8064-tsens.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From 0d0c22a59bf2672b57e23da9a9ea743e91b71f54 Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Sat, 25 Jul 2020 19:55:57 +0200
-Subject: [PATCH 08/10] drivers: thermal: tsens: Add support for ipq8064-tsens
-
-Add support for tsens present in ipq806x SoCs based on generic msm8960
-tsens driver.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
----
- drivers/thermal/qcom/tsens.c | 3 +++
- 1 file changed, 3 insertions(+)
-
---- a/drivers/thermal/qcom/tsens.c
-+++ b/drivers/thermal/qcom/tsens.c
-@@ -968,6 +968,9 @@ static SIMPLE_DEV_PM_OPS(tsens_pm_ops, t
- 
- static const struct of_device_id tsens_table[] = {
- 	{
-+		.compatible = "qcom,ipq8064-tsens",
-+		.data = &data_8960,
-+	}, {
- 		.compatible = "qcom,msm8916-tsens",
- 		.data = &data_8916,
- 	}, {
diff --git a/target/linux/ipq806x/patches-5.15/104-9-dt-bindings-thermal-tsens-Document-ipq8064-bindings.patch b/target/linux/ipq806x/patches-5.15/104-9-dt-bindings-thermal-tsens-Document-ipq8064-bindings.patch
deleted file mode 100644
index 382106863f..0000000000
--- a/target/linux/ipq806x/patches-5.15/104-9-dt-bindings-thermal-tsens-Document-ipq8064-bindings.patch
+++ /dev/null
@@ -1,112 +0,0 @@
-From ac369071920d427dd484cf74cddba2774bba45f5 Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Thu, 9 Jul 2020 22:35:54 +0200
-Subject: [PATCH 09/10] dt-bindings: thermal: tsens: Document ipq8064 bindings
-
-Document the use of bindings used for msm8960 tsens based devices.
-msm8960 use the same gcc regs and is set as a child of the qcom gcc.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Reviewed-by: Rob Herring <robh@kernel.org>
----
- .../bindings/thermal/qcom-tsens.yaml          | 56 ++++++++++++++++---
- 1 file changed, 48 insertions(+), 8 deletions(-)
-
---- a/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml
-+++ b/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml
-@@ -19,6 +19,11 @@ description: |
- properties:
-   compatible:
-     oneOf:
-+      - description: msm9860 TSENS based
-+        items:
-+          - enum:
-+              - qcom,ipq8064-tsens
-+
-       - description: v0.1 of TSENS
-         items:
-           - enum:
-@@ -73,7 +78,9 @@ properties:
-     maxItems: 2
-     items:
-       - const: calib
--      - const: calib_sel
-+      - enum:
-+          - calib_backup
-+          - calib_sel
- 
-   "#qcom,sensors":
-     description:
-@@ -88,12 +95,20 @@ properties:
-       Number of cells required to uniquely identify the thermal sensors. Since
-       we have multiple sensors this is set to 1
- 
-+required:
-+  - compatible
-+  - interrupts
-+  - interrupt-names
-+  - "#thermal-sensor-cells"
-+  - "#qcom,sensors"
-+
- allOf:
-   - if:
-       properties:
-         compatible:
-           contains:
-             enum:
-+              - qcom,ipq8064-tsens
-               - qcom,msm8916-tsens
-               - qcom,msm8974-tsens
-               - qcom,msm8976-tsens
-@@ -114,19 +129,44 @@ allOf:
-         interrupt-names:
-           minItems: 2
- 
--required:
--  - compatible
--  - reg
--  - "#qcom,sensors"
--  - interrupts
--  - interrupt-names
--  - "#thermal-sensor-cells"
-+  - if:
-+      properties:
-+        compatible:
-+          contains:
-+            enum:
-+              - qcom,tsens-v0_1
-+              - qcom,tsens-v1
-+              - qcom,tsens-v2
-+
-+    then:
-+      required:
-+        - reg
- 
- additionalProperties: false
- 
- examples:
-   - |
-     #include <dt-bindings/interrupt-controller/arm-gic.h>
-+    // Example msm9860 based SoC (ipq8064):
-+    gcc: clock-controller {
-+
-+           /* ... */
-+
-+           tsens: thermal-sensor {
-+                compatible = "qcom,ipq8064-tsens";
-+
-+                 nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
-+                 nvmem-cell-names = "calib", "calib_backup";
-+                 interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
-+                 interrupt-names = "uplow";
-+
-+                 #qcom,sensors = <11>;
-+                 #thermal-sensor-cells = <1>;
-+          };
-+    };
-+
-+  - |
-+    #include <dt-bindings/interrupt-controller/arm-gic.h>
-     // Example 1 (legacy: for pre v1 IP):
-     tsens1: thermal-sensor@900000 {
-            compatible = "qcom,msm8916-tsens", "qcom,tsens-v0_1";
diff --git a/target/linux/ipq806x/patches-5.15/105-10-drivers-thermal-tsens-Fix-wrong-slope-on-msm-8960.patch b/target/linux/ipq806x/patches-5.15/105-10-drivers-thermal-tsens-Fix-wrong-slope-on-msm-8960.patch
deleted file mode 100644
index 6cdc0b263f..0000000000
--- a/target/linux/ipq806x/patches-5.15/105-10-drivers-thermal-tsens-Fix-wrong-slope-on-msm-8960.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From 68e720ed73c8f038c8c500e4c49c1e65a993a448 Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Tue, 6 Apr 2021 04:45:31 +0200
-Subject: [PATCH 10/10] drivers: thermal: tsens: Fix wrong slope on msm-8960
-
-Some user using some stats with the old legacy implementation and the
-new implementation using the compute_intercept_slope reported an offset
-of 3C. Fix the slope table to reflect the original temp.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
----
- drivers/thermal/qcom/tsens-8960.c | 8 ++++----
- 1 file changed, 4 insertions(+), 4 deletions(-)
-
---- a/drivers/thermal/qcom/tsens-8960.c
-+++ b/drivers/thermal/qcom/tsens-8960.c
-@@ -45,11 +45,11 @@
- #define S9_STATUS_OFF		0x3674
- #define S10_STATUS_OFF		0x3678
- 
--/* Original slope - 200 to compensate mC to C inaccuracy */
-+/* Original slope - 350 to compensate mC to C inaccuracy */
- static u32 tsens_msm8960_slope[] = {
--			976, 976, 954, 976,
--			911, 932, 932, 999,
--			932, 999, 932
-+			826, 826, 804, 826,
-+			761, 782, 782, 849,
-+			782, 849, 782
- 			};
- 
- static int suspend_8960(struct tsens_priv *priv)
diff --git a/target/linux/ipq806x/patches-5.15/108-v5.14-net-stmmac-explicitly-deassert-gmac-ahb-reset.patch b/target/linux/ipq806x/patches-5.15/108-v5.14-net-stmmac-explicitly-deassert-gmac-ahb-reset.patch
deleted file mode 100644
index dd1e506e5b..0000000000
--- a/target/linux/ipq806x/patches-5.15/108-v5.14-net-stmmac-explicitly-deassert-gmac-ahb-reset.patch
+++ /dev/null
@@ -1,75 +0,0 @@
-From e67f325e9cd67562b761e884680c0fec03a6f404 Mon Sep 17 00:00:00 2001
-From: Matthew Hagan <mnhagan88@gmail.com>
-Date: Tue, 8 Jun 2021 19:59:06 +0100
-Subject: net: stmmac: explicitly deassert GMAC_AHB_RESET
-
-We are currently assuming that GMAC_AHB_RESET will already be deasserted
-by the bootloader. However if this has not been done, probing of the GMAC
-will fail. To remedy this we must ensure GMAC_AHB_RESET has been deasserted
-prior to probing.
-
-v2 changes:
- - remove NULL condition check for stmmac_ahb_rst in stmmac_main.c
- - unwrap dev_err() message in stmmac_main.c
- - add PTR_ERR() around plat->stmmac_ahb_rst in stmmac_platform.c
-
-v3 changes:
- - add error pointer to dev_err() output
- - add reset_control_assert(stmmac_ahb_rst) in stmmac_dvr_remove
- - revert PTR_ERR() around plat->stmmac_ahb_rst since this is performed
-   on the returned value of ret by the calling function
-
-Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
-Signed-off-by: David S. Miller <davem@davemloft.net>
----
- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c     | 5 +++++
- drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 6 ++++++
- include/linux/stmmac.h                                | 1 +
- 3 files changed, 12 insertions(+)
-
---- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
-+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
-@@ -5021,6 +5021,10 @@ int stmmac_dvr_probe(struct device *devi
- 			reset_control_reset(priv->plat->stmmac_rst);
- 	}
- 
-+	ret = reset_control_deassert(priv->plat->stmmac_ahb_rst);
-+	if (ret == -ENOTSUPP)
-+		dev_err(priv->device, "unable to bring out of ahb reset\n");
-+
- 	/* Init MAC and get the capabilities */
- 	ret = stmmac_hw_init(priv);
- 	if (ret)
-@@ -5245,6 +5249,7 @@ int stmmac_dvr_remove(struct device *dev
- 	phylink_destroy(priv->phylink);
- 	if (priv->plat->stmmac_rst)
- 		reset_control_assert(priv->plat->stmmac_rst);
-+	reset_control_assert(priv->plat->stmmac_ahb_rst);
- 	pm_runtime_put(dev);
- 	pm_runtime_disable(dev);
- 	if (priv->hw->pcs != STMMAC_PCS_TBI &&
---- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
-+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
-@@ -617,6 +617,12 @@ stmmac_probe_config_dt(struct platform_d
- 		plat->stmmac_rst = NULL;
- 	}
- 
-+	plat->stmmac_ahb_rst = devm_reset_control_get_optional_shared(
-+							&pdev->dev, "ahb");
-+	if (IS_ERR(plat->stmmac_ahb_rst))
-+		if (PTR_ERR(plat->stmmac_ahb_rst) == -EPROBE_DEFER)
-+			goto error_hw_init;
-+
- 	return plat;
- 
- error_hw_init:
---- a/include/linux/stmmac.h
-+++ b/include/linux/stmmac.h
-@@ -192,6 +192,7 @@ struct plat_stmmacenet_data {
- 	unsigned int clk_ref_rate;
- 	s32 ptp_max_adj;
- 	struct reset_control *stmmac_rst;
-+	struct reset_control *stmmac_ahb_rst;
- 	struct stmmac_axi *axi;
- 	int has_gmac4;
- 	bool has_sun8i;
diff --git a/target/linux/ipq806x/patches-5.15/109-v5.15-arm-dts-qcom-add-ahb-reset-to-ipq806x-gmac.patch b/target/linux/ipq806x/patches-5.15/109-v5.15-arm-dts-qcom-add-ahb-reset-to-ipq806x-gmac.patch
deleted file mode 100644
index 4a047ed6eb..0000000000
--- a/target/linux/ipq806x/patches-5.15/109-v5.15-arm-dts-qcom-add-ahb-reset-to-ipq806x-gmac.patch
+++ /dev/null
@@ -1,64 +0,0 @@
-From f95c4c56d65225a537a2d88735fde7ec4d37641d Mon Sep 17 00:00:00 2001
-From: Matthew Hagan <mnhagan88@gmail.com>
-Date: Sat, 5 Jun 2021 18:35:38 +0100
-Subject: ARM: dts: qcom: add ahb reset to ipq806x-gmac
-
-Add GMAC_AHB_RESET to the resets property of each gmac node.
-
-Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
-Link: https://lore.kernel.org/r/20210605173546.4102455-2-mnhagan88@gmail.com
-Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
----
- arch/arm/boot/dts/qcom-ipq8064.dtsi | 20 ++++++++++++--------
- 1 file changed, 12 insertions(+), 8 deletions(-)
-
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -1335,8 +1335,9 @@
- 			clocks = <&gcc GMAC_CORE1_CLK>;
- 			clock-names = "stmmaceth";
- 
--			resets = <&gcc GMAC_CORE1_RESET>;
--			reset-names = "stmmaceth";
-+			resets = <&gcc GMAC_CORE1_RESET>,
-+				 <&gcc GMAC_AHB_RESET>;
-+			reset-names = "stmmaceth", "ahb";
- 
- 			status = "disabled";
- 		};
-@@ -1358,8 +1359,9 @@
- 			clocks = <&gcc GMAC_CORE2_CLK>;
- 			clock-names = "stmmaceth";
- 
--			resets = <&gcc GMAC_CORE2_RESET>;
--			reset-names = "stmmaceth";
-+			resets = <&gcc GMAC_CORE2_RESET>,
-+				 <&gcc GMAC_AHB_RESET>;
-+			reset-names = "stmmaceth", "ahb";
- 
- 			status = "disabled";
- 		};
-@@ -1381,8 +1383,9 @@
- 			clocks = <&gcc GMAC_CORE3_CLK>;
- 			clock-names = "stmmaceth";
- 
--			resets = <&gcc GMAC_CORE3_RESET>;
--			reset-names = "stmmaceth";
-+			resets = <&gcc GMAC_CORE3_RESET>,
-+				 <&gcc GMAC_AHB_RESET>;
-+			reset-names = "stmmaceth", "ahb";
- 
- 			status = "disabled";
- 		};
-@@ -1404,8 +1407,9 @@
- 			clocks = <&gcc GMAC_CORE4_CLK>;
- 			clock-names = "stmmaceth";
- 
--			resets = <&gcc GMAC_CORE4_RESET>;
--			reset-names = "stmmaceth";
-+			resets = <&gcc GMAC_CORE4_RESET>,
-+				 <&gcc GMAC_AHB_RESET>;
-+			reset-names = "stmmaceth", "ahb";
- 
- 			status = "disabled";
- 		};