aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x
diff options
context:
space:
mode:
authorINAGAKI Hiroshi <musashino.open@gmail.com>2018-12-24 15:20:25 +0900
committerChristian Lamparter <chunkeey@gmail.com>2019-01-01 16:39:59 +0100
commit51fe956c4fbd6ea78f46a4aa835f142e94f32cee (patch)
treefd241b09e356baa4150380976314c27d8d71adac /target/linux/ipq806x
parent7e9b93fb1b9d1f04df905b77d79ef8a182b2fb83 (diff)
downloadupstream-51fe956c4fbd6ea78f46a4aa835f142e94f32cee.tar.gz
upstream-51fe956c4fbd6ea78f46a4aa835f142e94f32cee.tar.bz2
upstream-51fe956c4fbd6ea78f46a4aa835f142e94f32cee.zip
ipq806x: add support for Buffalo WXR-2533DHP
Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. The U-Boot on WXR-2533DHP employs a complicated dual firmware protection scheme against corruptions of the kernel and rootfs images. See the notes in buffalo.sh for details. specifications: - Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T) - 512 MB of RAM (DDR3) - 256 MB of Flash (NAND) - 4T4R 2.4/5 GHz Wlan (QCA9980) - 5x 10/100/1000 Mbps Ethernet - 10x LEDs, 8x keys (6x buttons, 2x slide-switches) - 2x USB 3.0 Type-A - 12VDC/4A AC Adapter - UART through-hole on PCB - J3: Vcc, GND, TX, RX from USB port side - 115200n8 Boot instructions for the initramfs image: 1. Prepare the TFTP server with the initramfs image renamed to "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10". 2. Press the "AOSS" button while powering on the WXR-2533DHP. 3. Wait until the "Wireless" LED flashes before releasing the AOSS button. The WXR-2533DHP will grab the image from TFTP server and will boot it. Flashing instructions: To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to let it finish the flashing process. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
Diffstat (limited to 'target/linux/ipq806x')
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/01_leds4
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata8
-rw-r--r--target/linux/ipq806x/base-files/lib/upgrade/buffalo.sh45
-rw-r--r--target/linux/ipq806x/base-files/lib/upgrade/platform.sh5
-rw-r--r--target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts535
-rw-r--r--target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064.dtsi4
-rw-r--r--target/linux/ipq806x/image/Makefile22
-rw-r--r--target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch3
9 files changed, 624 insertions, 3 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index 769afb8b85..509d334c41 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -11,6 +11,10 @@ board=$(board_name)
boardname="${board##*,}"
case "$board" in
+buffalo,wxr-2533dhp)
+ ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:white:wireless" "phy0tpt"
+ ucidef_set_led_switch "wan" "WAN" "${boardname}:white:internet" "switch0" "0x20"
+ ;;
compex,wpq864)
ucidef_set_led_usbport "usb" "USB" "wpq864:green:usb" "usb1-port1" "usb2-port1"
ucidef_set_led_usbport "pcie-usb" "PCIe USB" "wpq864:green:usb-pcie" "usb3-port1"
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index 3417466fbb..a3aa0fce70 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -12,6 +12,7 @@ board_config_update
board=$(board_name)
case "$board" in
+buffalo,wxr-2533dhp |\
compex,wpq864 |\
netgear,d7800 |\
netgear,r7500 |\
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index ba7a8e0b14..e05f2b2c7b 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -79,6 +79,10 @@ board=$(board_name)
case "$FIRMWARE" in
"ath10k/pre-cal-pci-0000:01:00.0.bin")
case $board in
+ buffalo,wxr-2533dhp)
+ ath10kcal_extract "ART" 4096 12064
+ ath10kcal_patch_mac_crc $(mtd_get_mac_binary ART 30)
+ ;;
linksys,ea8500)
ath10kcal_extract "art" 4096 12064
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +1)
@@ -109,6 +113,10 @@ case "$FIRMWARE" in
;;
"ath10k/pre-cal-pci-0001:01:00.0.bin")
case $board in
+ buffalo,wxr-2533dhp)
+ ath10kcal_extract "ART" 20480 12064
+ ath10kcal_patch_mac_crc $(mtd_get_mac_binary ART 24)
+ ;;
linksys,ea8500)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +2)
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/buffalo.sh b/target/linux/ipq806x/base-files/lib/upgrade/buffalo.sh
new file mode 100644
index 0000000000..77fa65e60e
--- /dev/null
+++ b/target/linux/ipq806x/base-files/lib/upgrade/buffalo.sh
@@ -0,0 +1,45 @@
+#!/bin/sh
+# Copyright (C) 2018 OpenWrt.org
+#
+
+. /lib/functions.sh
+
+# The mtd partition 'ubi' and 'rootfs_1' on NAND flash are os-image
+# partitions. These partitions are called as "Bank1/Bank2" in U-Boot
+# on WXR-2533DHP, and they are checked conditions when booting.
+# Then, U-Boot checks kernel and rootfs volumes in ubi, but U-Boot
+# needs "ubi_rootfs" as rootfs volume name. And, U-Boot checks the
+# checksum at the end of rootfs (ubi_rootfs).
+# When U-Boot writes os-image into the Bank, only kernel, rootfs
+# (ubi_rootfs) and rootfs_data (ubi_rootfs_data) volumes are wrote
+# into the Bank. (not full ubi image)
+#
+# == U-Boot Behaviors ==
+# - Bank1/Bank2 images are good, images are different
+# -> writes os-image to Bank1 from Bank2
+# (this behavior is used to firmware upgrade in stock firmware)
+# - Bank1 image is broken (or checksum error)
+# -> writes os-image to Bank1 from Bank2
+# - Bank2 image is broken (or checksum error)
+# -> writes os-image to Bank2 from Bank1
+# - Bank1/Bank2 images are broken (or checksum error)
+# -> start tftp
+
+buffalo_upgrade_prepare_ubi() {
+ local ubidev="$( nand_find_ubi ubi )"
+ local mtdnum2="$( find_mtd_index rootfs_1 )"
+
+ if [ ! "$mtdnum2" ]; then
+ echo "cannot find second ubi mtd partition rootfs_1"
+ return 1
+ fi
+
+ local ubidev2="$( nand_find_ubi rootfs_1 )"
+ if [ ! "$ubidev2" ] && [ -n "$mtdnum2" ]; then
+ ubiattach -m "$mtdnum2"
+ ubidev2="$( nand_find_ubi rootfs_1 )"
+ fi
+
+ ubirmvol /dev/$ubidev -N ubi_rootfs_data &> /dev/null || true
+ ubirmvol /dev/$ubidev2 -N kernel &> /dev/null || true
+}
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index 4b88f9cf5e..2f0190629e 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -10,6 +10,11 @@ platform_check_image() {
platform_do_upgrade() {
case "$(board_name)" in
+ buffalo,wxr-2533dhp)
+ buffalo_upgrade_prepare_ubi
+ CI_ROOTPART="ubi_rootfs"
+ nand_do_upgrade "$ARGV"
+ ;;
compex,wpq864|\
netgear,d7800 |\
netgear,r7500 |\
diff --git a/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts
new file mode 100644
index 0000000000..7b5ee799ee
--- /dev/null
+++ b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts
@@ -0,0 +1,535 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Buffalo WXR-2533DHP";
+ compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064";
+
+ memory@42000000 {
+ reg = <0x42000000 0x1e000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &gsbi4_serial;
+
+ led-boot = &power;
+ led-failsafe = &diag;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ chosen {
+ /* use "ubi_rootfs" volume in "ubi" partition as rootfs */
+ bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs";
+ stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ nand@1ac00000 {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ cs@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ubi@0 {
+ label = "ubi";
+ reg = <0x0000000 0x4000000>;
+ };
+
+ rootfs_1@4000000 {
+ label = "rootfs_1";
+ reg = <0x4000000 0x4000000>;
+ };
+ };
+ };
+ };
+
+ mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
+ <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ ethernet-phy@0 {
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x07600000 /* PAD0_MODE */
+ 0x00008 0x01000000 /* PAD5_MODE */
+ 0x0000c 0x00000080 /* PAD6_MODE */
+ 0x00050 0xcc35cc35 /* LED_CTRL0 */
+ 0x00054 0xca35ca35 /* LED_CTRL1 */
+ 0x00058 0xc935c935 /* LED_CTRL2 */
+ 0x0005c 0x03ffff00 /* LED_CTRL3 */
+ 0x000e4 0x0006a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x0000007e /* PORT0_STATUS */
+ 0x00094 0x0000007e /* PORT6_STATUS */
+ >;
+ };
+
+ ethernet-phy@4 {
+ reg = <4>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ usb {
+ label = "wxr-2533dhp:green:usb";
+ gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "usbport";
+ trigger-sources = <&hub_port0 &hub_port1>;
+ };
+
+ guestport {
+ label = "wxr-2533dhp:green:guestport";
+ gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ diag: diag {
+ label = "wxr-2533dhp:orange:diag";
+ gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ internet_orange {
+ label = "wxr-2533dhp:orange:internet";
+ gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ internet_white {
+ label = "wxr-2533dhp:white:internet";
+ gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+ };
+
+ wireless_orange {
+ label = "wxr-2533dhp:orange:wireless";
+ gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ wireless_white {
+ label = "wxr-2533dhp:white:wireless";
+ gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ router_orange {
+ label = "wxr-2533dhp:orange:router";
+ gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
+ };
+
+ router_white {
+ label = "wxr-2533dhp:white:router";
+ gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
+ };
+
+ power: power {
+ label = "wxr-2533dhp:white:power";
+ gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
+
+ power {
+ label = "power";
+ gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ eject {
+ label = "eject";
+ gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_EJECTCD>;
+ };
+
+ guest {
+ label = "guest";
+ gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ };
+
+ ap {
+ label = "ap";
+ gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ linux,input-type = <EV_SW>;
+ };
+
+ router {
+ label = "router";
+ gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ linux,input-type = <EV_SW>;
+ };
+
+ auto {
+ label = "auto";
+ gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ linux,input-type = <EV_SW>;
+ };
+ };
+};
+
+&adm_dma {
+ status = "okay";
+};
+
+&gmac1 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&ART 6>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "ok";
+
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&ART 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gsbi4 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+};
+
+&gsbi4_serial {
+ status = "okay";
+
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+};
+
+&gsbi5 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_SPI>;
+
+ spi@1a280000 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x0 0x10000>;
+ read-only;
+ };
+
+ MIBIB@10000 {
+ label = "MIBIB";
+ reg = <0x10000 0x20000>;
+ read-only;
+ };
+
+ SBL2@30000 {
+ label = "SBL2";
+ reg = <0x30000 0x30000>;
+ read-only;
+ };
+
+ SBL3@60000 {
+ label = "SBL3";
+ reg = <0x60000 0x30000>;
+ read-only;
+ };
+
+ DDRCONFIG@90000 {
+ label = "DDRCONFIG";
+ reg = <0x90000 0x10000>;
+ read-only;
+ };
+
+ SSD@a0000 {
+ label = "SSD";
+ reg = <0xa0000 0x10000>;
+ read-only;
+ };
+
+ TZ@b0000 {
+ label = "TZ";
+ reg = <0xb0000 0x30000>;
+ read-only;
+ };
+
+ RPM@e0000 {
+ label = "RPM";
+ reg = <0xe0000 0x20000>;
+ read-only;
+ };
+
+ APPSBL@100000 {
+ label = "APPSBL";
+ reg = <0x100000 0x70000>;
+ read-only;
+ };
+
+ APPSBLENV@170000 {
+ label = "APPSBLENV";
+ reg = <0x170000 0x10000>;
+ read-only;
+ };
+
+ ART: ART@180000 {
+ label = "ART";
+ reg = <0x180000 0x40000>;
+ read-only;
+ };
+
+ BOOTCONFIG@1c0000 {
+ label = "BOOTCONFIG";
+ reg = <0x1c0000 0x10000>;
+ read-only;
+ };
+
+ APPSBL_1@1d0000 {
+ label = "APPSBL_1";
+ reg = <0x1d0000 0x70000>;
+ read-only;
+ };
+ };
+ };
+ };
+};
+
+&hs_phy_0 { /* USB3 port 0 HS phy */
+ status = "okay";
+};
+
+&ss_phy_0 { /* USB3 port 0 SS phy */
+ status = "okay";
+};
+
+&hs_phy_1 { /* USB3 port 1 HS phy */
+ status = "okay";
+};
+
+&ss_phy_1 { /* USB3 port 1 SS phy */
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+
+ pinctrl-0 = <&usb_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&dwc3_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub_port0: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&dwc3_1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+};
+
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57",
+ "gpio58", "gpio64", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22",
+ "gpio23", "gpio24", "gpio25", "gpio26", "gpio53";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ uart0_pins: uart0_pins {
+ mux {
+ pins = "gpio10", "gpio11";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ bias-pull-down;
+ };
+
+ data {
+ pins = "gpio18", "gpio19";
+ drive-strength = <10>;
+ };
+
+ cs{
+ pins = "gpio20";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ clk {
+ pins = "gpio21";
+ drive-strength = <12>;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ mux {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39",
+ "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ pullups {
+ pins = "gpio39";
+ bias-pull-up;
+ };
+
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ bias-bus-hold;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ usb_pwr_en_pins: usb_pwr_en_pins {
+ mux{
+ pins = "gpio68";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ output-high;
+ };
+ };
+}; \ No newline at end of file
diff --git a/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064.dtsi b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064.dtsi
index d38fc29b68..08b8e003a8 100644
--- a/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -972,7 +972,7 @@
status = "disabled";
- dwc3@11000000 {
+ dwc3_0: dwc3@11000000 {
compatible = "snps,dwc3";
reg = <0x11000000 0xcd00>;
interrupts = <0 110 0x4>;
@@ -997,7 +997,7 @@
status = "disabled";
- dwc3@10000000 {
+ dwc3_1: dwc3@10000000 {
compatible = "snps,dwc3";
reg = <0x10000000 0xcd00>;
interrupts = <0 205 0x4>;
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index 6109765041..e1eb090de3 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -3,6 +3,13 @@
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
+define Build/buffalo-rootfs-cksum
+ ( \
+ echo -ne "\x$$(od -A n -t u1 $@ | tr -s ' ' '\n' | \
+ $(STAGING_DIR_HOST)/bin/awk '{s+=$$0}END{printf "%x", 255-s%256}')"; \
+ ) >> $@
+endef
+
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
@@ -72,6 +79,21 @@ define Device/ZyXELImage
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to $$$${BLOCKSIZE} | sysupgrade-tar rootfs=$$$$@ | append-metadata
endef
+define Device/buffalo_wxr-2533dhp
+ $(call Device/LegacyImage)
+ DEVICE_DTS := qcom-ipq8064-wxr-2533dhp
+ DEVICE_TITLE := Buffalo WXR-2533DHP
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 65536k
+ KERNEL_IN_UBI := 1
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-rootfs | buffalo-rootfs-cksum | \
+ sysupgrade-tar rootfs=$$$$@ | append-metadata
+ DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
+endef
+TARGET_DEVICES += buffalo_wxr-2533dhp
+
define Device/compex_wpq864
$(call Device/FitImage)
$(call Device/UbiFit)
diff --git a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch
index 0a62a0bc84..e11378b42a 100644
--- a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -699,6 +699,17 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -699,6 +699,18 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8084-mtp.dtb \
qcom-ipq4019-ap.dk01.1-c1.dtb \
qcom-ipq8064-ap148.dtb \
@@ -23,6 +23,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq8064-r7500v2.dtb \
+ qcom-ipq8064-wg2600hp.dtb \
+ qcom-ipq8064-wpq864.dtb \
++ qcom-ipq8064-wxr-2533dhp.dtb \
+ qcom-ipq8065-nbg6817.dtb \
+ qcom-ipq8065-r7800.dtb \
qcom-msm8660-surf.dtb \