aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x
diff options
context:
space:
mode:
authorChristian Lamparter <chunkeey@googlemail.com>2017-03-14 17:04:28 +0100
committerJohn Crispin <john@phrozen.org>2017-03-22 09:45:18 +0100
commit1cb406d019dc84497a8405c470f0b0394d5ff64a (patch)
tree1b83a4443b6e8a82bf8512dd4713be40d97f9830 /target/linux/ipq806x
parentc2d50bdeb34cfc359f28aeb2fe7648cc335bc623 (diff)
downloadupstream-1cb406d019dc84497a8405c470f0b0394d5ff64a.tar.gz
upstream-1cb406d019dc84497a8405c470f0b0394d5ff64a.tar.bz2
upstream-1cb406d019dc84497a8405c470f0b0394d5ff64a.zip
ipq806x: add ipq4019 fritz4040 support
This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
Diffstat (limited to 'target/linux/ipq806x')
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/01_leds5
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/02_network5
-rw-r--r--target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata15
-rw-r--r--target/linux/ipq806x/base-files/lib/ipq806x.sh3
-rw-r--r--target/linux/ipq806x/base-files/lib/upgrade/platform.sh3
-rw-r--r--target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-fritz4040.dts2
-rw-r--r--target/linux/ipq806x/image/Makefile26
7 files changed, 55 insertions, 4 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index 977b3b104e..1371767268 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -26,6 +26,11 @@ r7800)
ucidef_set_led_netdev "wan" "WAN" "${board}:white:wan" "eth0"
ucidef_set_led_ide "esata" "eSATA" "${board}:white:esata"
;;
+fritz4040)
+ ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" "phy1tpt"
+ ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1"
+ ucidef_set_led_switch "lan" "LAN" "${board}:green:lan" "switch0" "0x1e"
+ ;;
nbg6817)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:amber:wifi2g" "phy1tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:amber:wifi5g" "phy0tpt"
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index 52bb1629f7..36e0fb3a0e 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -36,6 +36,11 @@ ea8500)
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
;;
+fritz4040)
+ ucidef_set_interfaces_lan_wan "eth0" "eth1"
+ ucidef_add_switch "switch0" \
+ "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
+ ;;
nbg6817)
hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 72c3ae88c2..652621247f 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -46,6 +46,21 @@ board=$(ipq806x_board_name)
case "$FIRMWARE" in
+"ath10k/pre-cal-ahb-a000000.wifi.bin")
+ case "$board" in
+ fritz4040)
+ /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
+ ;;
+ esac
+ ;;
+"ath10k/pre-cal-ahb-a800000.wifi.bin")
+ case "$board" in
+ fritz4040)
+ /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
+ ;;
+ esac
+ ;;
+
"ath10k/cal-pci-0000:01:00.0.bin")
case $board in
c2600)
diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh
index a8b909ac04..348a3a8951 100644
--- a/target/linux/ipq806x/base-files/lib/ipq806x.sh
+++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh
@@ -17,6 +17,9 @@ ipq806x_board_detect() {
*"AP148")
name="ap148"
;;
+ *"4040")
+ name="fritz4040"
+ ;;
*"C2600")
name="c2600"
;;
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index c3741f9ff2..89702850fc 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -42,6 +42,9 @@ platform_do_upgrade() {
MTD_CONFIG_ARGS="-s 0x200000"
default_do_upgrade "$ARGV"
;;
+ *)
+ default_do_upgrade "$ARGV"
+ ;;
esac
}
diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-fritz4040.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-fritz4040.dts
index fdd565c2ea..1bd5b512c8 100644
--- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-fritz4040.dts
+++ b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-fritz4040.dts
@@ -272,7 +272,7 @@
read-only;
};
partition11@2A0000 {
- label = "image"; /* firmware */
+ label = "firmware";
reg = <0x002A0000 0x01C60000>;
};
partition12@1f00000 {
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index 70c8056d90..8091d9951a 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -5,8 +5,6 @@ include $(INCLUDE_DIR)/image.mk
UBIFS_OPTS = -m 2048 -e 124KiB -c 4096 -U -F
-KERNEL_LOADADDR := 0x42208000
-
define Image/Prepare
$(CP) $(LINUX_DIR)/vmlinux $(KDIR)/$(IMG_PREFIX)-vmlinux.elf
endef
@@ -30,6 +28,7 @@ define Device/Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
KERNEL_PREFIX := $$(IMAGE_PREFIX)
+ KERNEL_LOADADDR = 0x42208000
SUPPORTED_DEVICES = $$(BOARD_NAME)
IMAGE/sysupgrade.tar = sysupgrade-tar | append-metadata
endef
@@ -46,6 +45,12 @@ define Device/FitImage
KERNEL_NAME := Image
endef
+define Device/FitImageLzma
+ KERNEL_SUFFIX := -fit-uImage.itb
+ KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
+ KERNEL_NAME := Image
+endef
+
define Device/UbiFit
KERNEL_IN_UBI := 1
IMAGES := nand-factory.ubi nand-sysupgrade.tar
@@ -165,6 +170,20 @@ define Device/EA8500
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
+define Device/FRITZ4040
+ $(call Device/FitImageLzma)
+ DEVICE_DTS := qcom-ipq4019-fritz4040
+ KERNEL_LOADADDR := 0x80208000
+ BLOCKSIZE := 4k
+ PAGESIZE := 256
+ BOARD_NAME := fritz4040
+ DEVICE_TITLE := AVM Fritz!Box 4040
+ IMAGE_SIZE := 29753344
+ IMAGES = sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+ DEVICE_PACKAGES := kmod-usb-phy-qcom-ipq4019 ipq-wifi-fritz4040 fritz-tools u-boot-fritz4040
+endef
+
define Device/R7500
$(call Device/DniImage)
DEVICE_DTS := qcom-ipq8064-r7500
@@ -231,6 +250,7 @@ define Device/VR2600v
IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
endef
-TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817 VR2600v
+TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 FRITZ4040 R7500 \
+ R7500v2 R7800 NBG6817 VR2600v
$(eval $(call BuildImage))