ipq806x: update target to v3.18

Patches in the ipq806x/patches folder were out of tree in v3.14. The
newest patch at the time was from June, so we can safely assume that
either the patches have been merged, or they have been rejected for
a good reason. If patches are seen missing, we'll cherry-pick them
on a per-needed basis.

This new kernel have been tested on AP148, which seems to works fine.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 44386

1 files changed, 0 insertions, 83 deletions

diff --git a/target/linux/ipq806x/patches/0133-spi-qup-Remove-chip-select-function.patch b/target/linux/ipq806x/patches/0133-spi-qup-Remove-chip-select-function.patch
deleted file mode 100644
index 14ae782b49..0000000000
--- a/target/linux/ipq806x/patches/0133-spi-qup-Remove-chip-select-function.patch
+++ /dev/null
@@ -1,83 +0,0 @@
-From 9bc674f40f22596ef8c2ff6d7f9e53da0baa57e9 Mon Sep 17 00:00:00 2001
-From: Andy Gross <agross@codeaurora.org>
-Date: Thu, 12 Jun 2014 14:34:10 -0500
-Subject: [PATCH 133/182] spi: qup: Remove chip select function
-
-This patch removes the chip select function.  Chip select should instead be
-supported using GPIOs, defining the DT entry "cs-gpios", and letting the SPI
-core assert/deassert the chip select as it sees fit.
-
-Signed-off-by: Andy Gross <agross@codeaurora.org>
----
- .../devicetree/bindings/spi/qcom,spi-qup.txt       |    6 ++++
- drivers/spi/spi-qup.c                              |   33 ++++----------------
- 2 files changed, 12 insertions(+), 27 deletions(-)
-
---- a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
-+++ b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
-@@ -23,6 +23,12 @@ Optional properties:
- - spi-max-frequency: Specifies maximum SPI clock frequency,
-                      Units - Hz. Definition as per
-                      Documentation/devicetree/bindings/spi/spi-bus.txt
-+- num-cs:	total number of chipselects
-+- cs-gpios:	should specify GPIOs used for chipselects.
-+		The gpios will be referred to as reg = <index> in the SPI child
-+		nodes.  If unspecified, a single SPI device without a chip
-+		select can be used.
-+
- 
- SPI slave nodes must be children of the SPI master node and can contain
- properties described in Documentation/devicetree/bindings/spi/spi-bus.txt
---- a/drivers/spi/spi-qup.c
-+++ b/drivers/spi/spi-qup.c
-@@ -424,31 +424,6 @@ static int spi_qup_io_config(struct spi_
- 	return 0;
- }
- 
--static void spi_qup_set_cs(struct spi_device *spi, bool enable)
--{
--	struct spi_qup *controller = spi_master_get_devdata(spi->master);
--
--	u32 iocontol, mask;
--
--	iocontol = readl_relaxed(controller->base + SPI_IO_CONTROL);
--
--	/* Disable auto CS toggle and use manual */
--	iocontol &= ~SPI_IO_C_MX_CS_MODE;
--	iocontol |= SPI_IO_C_FORCE_CS;
--
--	iocontol &= ~SPI_IO_C_CS_SELECT_MASK;
--	iocontol |= SPI_IO_C_CS_SELECT(spi->chip_select);
--
--	mask = SPI_IO_C_CS_N_POLARITY_0 << spi->chip_select;
--
--	if (enable)
--		iocontol |= mask;
--	else
--		iocontol &= ~mask;
--
--	writel_relaxed(iocontol, controller->base + SPI_IO_CONTROL);
--}
--
- static int spi_qup_transfer_one(struct spi_master *master,
- 			      struct spi_device *spi,
- 			      struct spi_transfer *xfer)
-@@ -571,12 +546,16 @@ static int spi_qup_probe(struct platform
- 		return -ENOMEM;
- 	}
- 
-+	/* use num-cs unless not present or out of range */
-+	if (of_property_read_u16(dev->of_node, "num-cs",
-+			&master->num_chipselect) ||
-+			(master->num_chipselect > SPI_NUM_CHIPSELECTS))
-+		master->num_chipselect = SPI_NUM_CHIPSELECTS;
-+
- 	master->bus_num = pdev->id;
- 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
--	master->num_chipselect = SPI_NUM_CHIPSELECTS;
- 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
- 	master->max_speed_hz = max_freq;
--	master->set_cs = spi_qup_set_cs;
- 	master->transfer_one = spi_qup_transfer_one;
- 	master->dev.of_node = pdev->dev.of_node;
- 	master->auto_runtime_pm = true;