ipq806x: update target to v3.18

Patches in the ipq806x/patches folder were out of tree in v3.14. The
newest patch at the time was from June, so we can safely assume that
either the patches have been merged, or they have been rejected for
a good reason. If patches are seen missing, we'll cherry-pick them
on a per-needed basis.

This new kernel have been tested on AP148, which seems to works fine.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 44386

1 files changed, 0 insertions, 114 deletions

diff --git a/target/linux/ipq806x/patches/0041-dt-Document-Qualcomm-IPQ8064-pinctrl-binding.patch b/target/linux/ipq806x/patches/0041-dt-Document-Qualcomm-IPQ8064-pinctrl-binding.patch
deleted file mode 100644
index c1adc991d8..0000000000
--- a/target/linux/ipq806x/patches/0041-dt-Document-Qualcomm-IPQ8064-pinctrl-binding.patch
+++ /dev/null
@@ -1,114 +0,0 @@
-From 425015979d3b1600d14403be7d6d64ba1238e58d Mon Sep 17 00:00:00 2001
-From: Andy Gross <agross@codeaurora.org>
-Date: Mon, 14 Apr 2014 22:10:36 -0500
-Subject: [PATCH 041/182] dt: Document Qualcomm IPQ8064 pinctrl binding
-
-Define a new binding for the Qualcomm TLMMv2 based pin controller inside the
-IPQ8064.
-
-Signed-off-by: Andy Gross <agross@codeaurora.org>
-Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
-Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
----
- .../bindings/pinctrl/qcom,ipq8064-pinctrl.txt      |   95 ++++++++++++++++++++
- 1 file changed, 95 insertions(+)
- create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
-
---- /dev/null
-+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
-@@ -0,0 +1,95 @@
-+Qualcomm IPQ8064 TLMM block
-+
-+Required properties:
-+- compatible: "qcom,ipq8064-pinctrl"
-+- reg: Should be the base address and length of the TLMM block.
-+- interrupts: Should be the parent IRQ of the TLMM block.
-+- interrupt-controller: Marks the device node as an interrupt controller.
-+- #interrupt-cells: Should be two.
-+- gpio-controller: Marks the device node as a GPIO controller.
-+- #gpio-cells : Should be two.
-+                The first cell is the gpio pin number and the
-+                second cell is used for optional parameters.
-+
-+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-+a general description of GPIO and interrupt bindings.
-+
-+Please refer to pinctrl-bindings.txt in this directory for details of the
-+common pinctrl bindings used by client devices, including the meaning of the
-+phrase "pin configuration node".
-+
-+Qualcomm's pin configuration nodes act as a container for an abitrary number of
-+subnodes. Each of these subnodes represents some desired configuration for a
-+pin, a group, or a list of pins or groups. This configuration can include the
-+mux function to select on those pin(s)/group(s), and various pin configuration
-+parameters, such as pull-up, drive strength, etc.
-+
-+The name of each subnode is not important; all subnodes should be enumerated
-+and processed purely based on their content.
-+
-+Each subnode only affects those parameters that are explicitly listed. In
-+other words, a subnode that lists a mux function but no pin configuration
-+parameters implies no information about any pin configuration parameters.
-+Similarly, a pin subnode that describes a pullup parameter implies no
-+information about e.g. the mux function.
-+
-+
-+The following generic properties as defined in pinctrl-bindings.txt are valid
-+to specify in a pin configuration subnode:
-+
-+ pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength,
-+ output-low, output-high.
-+
-+Non-empty subnodes must specify the 'pins' property.
-+
-+Valid values for qcom,pins are:
-+  gpio0-gpio68
-+   Supports mux, bias, and drive-strength
-+
-+  sdc3_clk, sdc3_cmd, sdc3_data
-+   Supports bias and drive-strength
-+
-+
-+Valid values for function are:
-+  mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gsbi1, gsbi2, gsbi4, gsbi5,
-+  gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1,
-+  spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata,
-+  pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt,
-+  pcie1_clk_req, pcie2_rst, pcie2_prsnt, pcie2_pwren_n, pcie2_pwren,
-+  pcie2_pwrflt, pcie2_clk_req, pcie3_rst, pcie3_prsnt, pcie3_pwren_n,
-+  pcie3_pwren, pcie3_pwrflt, pcie3_clk_req, ps_hold
-+
-+Example:
-+
-+	pinmux: pinctrl@800000 {
-+		compatible = "qcom,ipq8064-pinctrl";
-+		reg = <0x800000 0x4000>;
-+
-+		gpio-controller;
-+		#gpio-cells = <2>;
-+		interrupt-controller;
-+		#interrupt-cells = <2>;
-+		interrupts = <0 32 0x4>;
-+
-+		pinctrl-names = "default";
-+		pinctrl-0 = <&gsbi5_uart_default>;
-+
-+		gsbi5_uart_default: gsbi5_uart_default {
-+			mux {
-+				pins = "gpio18", "gpio19";
-+				function = "gsbi5";
-+			};
-+
-+			tx {
-+				pins = "gpio18";
-+				drive-strength = <4>;
-+				bias-disable;
-+			};
-+
-+			rx {
-+				pins = "gpio19";
-+				drive-strength = <2>;
-+				bias-pull-up;
-+			};
-+		};
-+	};