ipq806x: remove support for kernel 4.19

The target uses 5.4 as default kernel since 04/2020.

Kernel 4.19 support is not really maintained anymore, and there has
been a lot of changes between 4.19 and 5.4 on this target. Despite,
new devices are typically added for 5.4 only anyway.

Thus, make maintaining of old stuff and reviewing of new stuff
easier by removing support for kernel 4.19.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

19 files changed, 5156 insertions, 0 deletions

diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
new file mode 100644
index 0000000000..b2fdc427e2
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
@@ -0,0 +1,121 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8064/AP-148";
+	compatible = "qcom,ipq8064-ap148", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
+
+&flash {
+	partitions {
+		compatible = "qcom,smem";
+	};
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+	max-link-speed = <1>;
+};
+
+&nand_controller {
+	status = "okay";
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+
+	nand@0 {
+		reg = <0>;
+		compatible = "qcom,nandcs";
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "qcom,smem";
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x80        /* PAD6_MODE */
+			0x000e4 0x6a545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+			>;
+	};
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap161.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap161.dts
new file mode 100644
index 0000000000..6ba3d70808
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap161.dts
@@ -0,0 +1,159 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+/ {
+	model = "Qualcomm IPQ8064/AP161";
+	compatible = "qcom,ipq8064-ap161", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+	};
+};
+
+&qcom_pinmux {
+	rgmii2_pins: rgmii2_pins {
+		mux {
+			pins = "gpio27", "gpio28", "gpio29",
+			       "gpio30", "gpio31", "gpio32",
+			       "gpio51", "gpio52", "gpio59",
+			       "gpio60", "gpio61", "gpio62",
+			       "gpio2", "gpio66";
+		};
+	};
+};
+
+&flash {
+	partitions {
+		compatible = "qcom,smem";
+	};
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+	max-link-speed = <1>;
+};
+
+&pcie2 {
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+
+	nand@0 {
+		reg = <0>;
+		compatible = "qcom,nandcs";
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "qcom,smem";
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x20080     /* PAD6_MODE */
+			0x000e4 0x6a545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+			>;
+	};
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+		qca,phy-rgmii-en;
+		qca,txclk-delay-en;
+		qca,rxclk-delay-en;
+	};
+
+	phy3: ethernet-phy@3 {
+		device_type = "ethernet-phy";
+		reg = <3>;
+	};
+};
+
+&gmac0 {
+	status = "okay";
+	phy-mode = "rgmii";
+	qcom,id = <0>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+	mdiobus = <&mdio0>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+	mdiobus = <&mdio0>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+	mdiobus = <&mdio0>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
new file mode 100644
index 0000000000..4ae7de604b
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
@@ -0,0 +1,417 @@
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "TP-Link Archer C2600";
+	compatible = "tplink,c2600", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power;
+		led-failsafe = &general;
+		led-running = &power;
+		led-upgrade = &general;
+		label-mac-device = &gmac2;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 49 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		ledswitch {
+			label = "ledswitch";
+			gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LIGHTS_TOGGLE>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		lan {
+			label = "white:lan";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb4 {
+			label = "white:usb_4";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb2 {
+			label = "white:usb_2";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		wps {
+			label = "white:wps";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_amber {
+			label = "amber:wan";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
+		};
+
+		wan_white {
+			label = "white:wan";
+			gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>;
+		};
+
+		power: power {
+			label = "white:power";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		general: general {
+			label = "white:general";
+			gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&qcom_pinmux {
+	button_pins: button_pins {
+		mux {
+			pins = "gpio16", "gpio54", "gpio65";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33",
+					"gpio53", "gpio66";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	spi_pins: spi_pins {
+		mux {
+			pins = "gpio18", "gpio19", "gpio21";
+			function = "gsbi5";
+			bias-pull-down;
+		};
+
+		data {
+			pins = "gpio18", "gpio19";
+			drive-strength = <10>;
+		};
+
+		cs {
+			pins = "gpio20";
+			function = "gpio";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+
+		clk {
+			pins = "gpio21";
+			drive-strength = <12>;
+		};
+	};
+
+	usb0_pwr_en_pin: usb0_pwr_en_pin {
+		mux {
+			pins = "gpio25";
+			function = "gpio";
+			drive-strength = <10>;
+			bias-pull-up;
+			output-high;
+		};
+	};
+
+	usb1_pwr_en_pin: usb1_pwr_en_pin {
+		mux {
+			pins = "gpio23";
+			function = "gpio";
+			drive-strength = <10>;
+			bias-pull-up;
+			output-high;
+		};
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	status = "okay";
+
+	spi5: spi@1a280000 {
+		status = "okay";
+
+		pinctrl-0 = <&spi_pins>;
+		pinctrl-names = "default";
+
+		cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+		m25p80@0 {
+			compatible = "jedec,spi-nor";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			spi-max-frequency = <50000000>;
+			reg = <0>;
+
+			SBL1@0 {
+				label = "SBL1";
+				reg = <0x0 0x20000>;
+				read-only;
+			};
+
+			MIBIB@20000 {
+				label = "MIBIB";
+				reg = <0x20000 0x20000>;
+				read-only;
+			};
+
+			SBL2@40000 {
+				label = "SBL2";
+				reg = <0x40000 0x20000>;
+				read-only;
+			};
+
+			SBL3@60000 {
+				label = "SBL3";
+				reg = <0x60000 0x30000>;
+				read-only;
+			};
+
+			DDRCONFIG@90000 {
+				label = "DDRCONFIG";
+				reg = <0x90000 0x10000>;
+				read-only;
+			};
+
+			SSD@a0000 {
+				label = "SSD";
+				reg = <0xa0000 0x10000>;
+				read-only;
+			};
+
+			TZ@b0000 {
+				label = "TZ";
+				reg = <0xb0000 0x30000>;
+				read-only;
+			};
+
+			RPM@e0000 {
+				label = "RPM";
+				reg = <0xe0000 0x20000>;
+				read-only;
+			};
+
+			fs-uboot@100000 {
+				label = "fs-uboot";
+				reg = <0x100000 0x70000>;
+				read-only;
+			};
+
+			uboot-env@170000 {
+				label = "uboot-env";
+				reg = <0x170000 0x40000>;
+				read-only;
+			};
+
+			radio@1b0000 {
+				label = "radio";
+				reg = <0x1b0000 0x40000>;
+				read-only;
+			};
+
+			os-image@1f0000 {
+				label = "os-image";
+				reg = <0x1f0000 0x400000>;
+			};
+
+			rootfs@5f0000 {
+				label = "rootfs";
+				reg = <0x5f0000 0x1900000>;
+			};
+
+			defaultmac: default-mac@1ef0000 {
+				label = "default-mac";
+				reg = <0x1ef0000 0x00200>;
+				read-only;
+			};
+
+			pin@1ef0200 {
+				label = "pin";
+				reg = <0x1ef0200 0x00200>;
+				read-only;
+			};
+
+			product-info@1ef0400 {
+				label = "product-info";
+				reg = <0x1ef0400 0x0fc00>;
+				read-only;
+			};
+
+			partition-table@1f00000 {
+				label = "partition-table";
+				reg = <0x1f00000 0x10000>;
+				read-only;
+			};
+
+			soft-version@1f10000 {
+				label = "soft-version";
+				reg = <0x1f10000 0x10000>;
+				read-only;
+			};
+
+			support-list@1f20000 {
+				label = "support-list";
+				reg = <0x1f20000 0x10000>;
+				read-only;
+			};
+
+			profile@1f30000 {
+				label = "profile";
+				reg = <0x1f30000 0x10000>;
+				read-only;
+			};
+
+			default-config@1f40000 {
+				label = "default-config";
+				reg = <0x1f40000 0x10000>;
+				read-only;
+			};
+
+			user-config@1f50000 {
+				label = "user-config";
+				reg = <0x1f50000 0x40000>;
+				read-only;
+			};
+
+			qos-db@1f90000 {
+				label = "qos-db";
+				reg = <0x1f90000 0x40000>;
+				read-only;
+			};
+
+			usb-config@1fd0000 {
+				label = "usb-config";
+				reg = <0x1fd0000 0x10000>;
+				read-only;
+			};
+
+			log@1fe0000 {
+				label = "log";
+				reg = <0x1fe0000 0x20000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&usb3_0 {
+	status = "okay";
+
+	pinctrl-0 = <&usb0_pwr_en_pin>;
+	pinctrl-names = "default";
+};
+
+&usb3_1 {
+	status = "okay";
+
+	pinctrl-0 = <&usb1_pwr_en_pin>;
+	pinctrl-names = "default";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+	max-link-speed = <1>;
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x80        /* PAD6_MODE */
+			0x000e4 0x6a545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+			>;
+	};
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	mtd-mac-address = <&defaultmac 0x8>;
+	mtd-mac-address-increment = <1>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+
+	mtd-mac-address = <&defaultmac 0x8>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts
new file mode 100644
index 0000000000..7fb871be78
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts
@@ -0,0 +1,310 @@
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear Nighthawk X4 D7800";
+	compatible = "netgear,d7800", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0xe000000>;
+		device_type = "memory";
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power_white;
+		led-failsafe = &power_amber;
+		led-running = &power_white;
+		led-upgrade = &power_amber;
+	};
+
+	chosen {
+		bootargs = "rootfstype=squashfs noinitrd";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		usb1 {
+			label = "white:usb1";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb2 {
+			label = "white:usb2";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_amber: power_amber {
+			label = "amber:power";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_white {
+			label = "white:wan";
+			gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_amber {
+			label = "amber:wan";
+			gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		wps {
+			label = "white:wps";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+		};
+
+		esata {
+			label = "white:esata";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_white: power_white {
+			label = "white:power";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		wifi {
+			label = "white:wifi";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&qcom_pinmux {
+	button_pins: button_pins {
+		mux {
+			pins = "gpio6", "gpio54", "gpio65";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+				"gpio24","gpio26", "gpio53", "gpio64";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	usb0_pwr_en_pins: usb0_pwr_en_pins {
+		mux {
+			pins = "gpio15";
+			function = "gpio";
+			drive-strength = <12>;
+			bias-pull-down;
+			output-high;
+		};
+	};
+
+	usb1_pwr_en_pins: usb1_pwr_en_pins {
+		mux {
+			pins = "gpio16", "gpio68";
+			function = "gpio";
+			drive-strength = <12>;
+			bias-pull-down;
+			output-high;
+		};
+	};
+};
+
+&sata_phy {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&usb3_0 {
+	status = "okay";
+
+	pinctrl-0 = <&usb0_pwr_en_pins>;
+	pinctrl-names = "default";
+};
+
+&usb3_1 {
+	status = "okay";
+
+	pinctrl-0 = <&usb1_pwr_en_pins>;
+	pinctrl-names = "default";
+};
+
+&pcie0 {
+	status = "okay";
+	reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
+	pinctrl-0 = <&pcie0_pins>;
+	pinctrl-names = "default";
+};
+
+&pcie1 {
+	status = "okay";
+	reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
+	pinctrl-0 = <&pcie1_pins>;
+	pinctrl-names = "default";
+	max-link-speed = <1>;
+};
+
+&nand_controller {
+	status = "okay";
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	nand@0 {
+		reg = <0>;
+		compatible = "qcom,nandcs";
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qcadata@0 {
+				label = "qcadata";
+				reg = <0x0000000 0x0c80000>;
+				read-only;
+			};
+
+			APPSBL@c80000 {
+				label = "APPSBL";
+				reg = <0x0c80000 0x0500000>;
+				read-only;
+			};
+
+			APPSBLENV@1180000 {
+				label = "APPSBLENV";
+				reg = <0x1180000 0x0080000>;
+				read-only;
+			};
+
+			art: art@1200000 {
+				label = "art";
+				reg = <0x1200000 0x0140000>;
+				read-only;
+			};
+
+			artbak: art@1340000 {
+				label = "artbak";
+				reg = <0x1340000 0x0140000>;
+				read-only;
+			};
+
+			kernel@1480000 {
+				label = "kernel";
+				reg = <0x1480000 0x0400000>;
+			};
+
+			ubi@1880000 {
+				label = "ubi";
+				reg = <0x1880000 0x1C00000>;
+			};
+
+			netgear@3480000 {
+				label = "netgear";
+				reg = <0x3480000 0x4480000>;
+				read-only;
+			};
+
+			reserve@7900000 {
+				label = "reserve";
+				reg = <0x7900000 0x0700000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x80        /* PAD6_MODE */
+			0x000e4 0x6a545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+			>;
+	};
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&phy4>;
+	qcom,id = <1>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	mtd-mac-address = <&art 6>;
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+
+	mtd-mac-address = <&art 0>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-db149.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-db149.dts
new file mode 100644
index 0000000000..8e8d942fbd
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-db149.dts
@@ -0,0 +1,163 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+/ {
+	model = "Qualcomm IPQ8064/DB149";
+	compatible = "qcom,ipq8064-db149", "qcom,ipq8064";
+
+	aliases {
+		serial0 = &gsbi2_serial;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+};
+
+&qcom_pinmux {
+	rgmii0_pins: rgmii0_pins {
+		mux {
+			pins = "gpio2", "gpio66";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+};
+
+&gsbi2 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+
+	gsbi2_serial: serial@12490000 {
+		status = "okay";
+	};
+};
+
+&gsbi4 {
+	status = "disabled";
+};
+
+&gsbi4_serial {
+	status = "disabled";
+};
+
+&flash {
+	m25p,fast-read;
+
+	partition@0 {
+		label = "lowlevel_init";
+		reg = <0x0 0x1b0000>;
+	};
+
+	partition@1 {
+		label = "u-boot";
+		reg = <0x1b0000 0x80000>;
+	};
+
+	partition@2 {
+		label = "u-boot-env";
+		reg = <0x230000 0x40000>;
+	};
+
+	partition@3 {
+		label = "caldata";
+		reg = <0x270000 0x40000>;
+	};
+
+	partition@4 {
+		label = "firmware";
+		reg = <0x2b0000 0x1d50000>;
+	};
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pcie2 {
+	status = "okay";
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x80        /* PAD6_MODE */
+			0x000e4 0x6a545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+		>;
+	};
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+
+	phy6: ethernet-phy@6 {
+		reg = <6>;
+	};
+
+	phy7: ethernet-phy@7 {
+		reg = <7>;
+	};
+};
+
+&gmac0 {
+	status = "okay";
+	phy-mode = "rgmii";
+	qcom,id = <0>;
+	phy-handle = <&phy4>;
+
+	pinctrl-0 = <&rgmii0_pins>;
+	pinctrl-names = "default";
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <1>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+	phy-handle = <&phy6>;
+};
+
+&gmac3 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <3>;
+	phy-handle = <&phy7>;
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea7500-v1.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea7500-v1.dts
new file mode 100644
index 0000000000..176807163e
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea7500-v1.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq8064-eax500.dtsi"
+
+/ {
+	model = "Linksys EA7500 V1 WiFi Router";
+	compatible = "linksys,ea7500-v1", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0xe000000>;
+		device_type = "memory";
+	};
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	chosen {
+		/* look for root deviceblock nbr in this bootarg */
+		find-rootblock = "ubi.mtd=";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		led_power: power {
+			label = "white:power";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+	};
+};
+
+&qcom_pinmux {
+	button_pins: button_pins {
+		mux {
+			pins = "gpio65", "gpio68";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio6";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&partitions {
+	partition@5f80000 {
+		label = "sysdiag";
+		reg = <0x5f80000 0x100000>;
+	};
+
+	partition@6080000 {
+		label = "syscfg";
+		reg = <0x6080000 0x1f80000>;
+	};
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts
new file mode 100644
index 0000000000..9b01ae0328
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts
@@ -0,0 +1,122 @@
+#include "qcom-ipq8064-eax500.dtsi"
+
+/ {
+	model = "Linksys EA8500 WiFi Router";
+	compatible = "linksys,ea8500", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		wps {
+			label = "green:wps";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_power: power {
+			label = "white:power";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+
+		wifi {
+			label = "green:wifi";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&qcom_pinmux {
+	button_pins: button_pins {
+		mux {
+			pins = "gpio65", "gpio67", "gpio68";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio6", "gpio53", "gpio54";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&sata_phy {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&partitions {
+	partition@5f80000 {
+		label = "syscfg";
+		reg = <0x5f80000 0x2080000>;
+	};
+};
+
+&mdio0 {
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&gmac1 {
+	qcom,phy_mdio_addr = <4>;
+	qcom,poll_required = <1>;
+	qcom,rgmii_delay = <0>;
+	qcom,emulation = <0>;
+};
+
+/* LAN */
+&gmac2 {
+	qcom,phy_mdio_addr = <0>;	/* none */
+	qcom,poll_required = <0>;	/* no polling */
+	qcom,rgmii_delay = <0>;
+	qcom,emulation = <0>;
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi
new file mode 100644
index 0000000000..3e6732e9df
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi
@@ -0,0 +1,204 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	chosen {
+		bootargs = "console=ttyMSM0,115200n8";
+		/* append to bootargs adding the root deviceblock nbr from bootloader */
+		append-rootblock = "ubi.mtd=";
+	};
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+
+	max-link-speed = <1>;
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pcie2 {
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+
+	nand@0 {
+		reg = <0>;
+		compatible = "qcom,nandcs";
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions: partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x0000000 0x0040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "MIBIB";
+				reg = <0x0040000 0x0140000>;
+				read-only;
+			};
+
+			partition@180000 {
+				label = "SBL2";
+				reg = <0x0180000 0x0140000>;
+				read-only;
+			};
+
+			partition@2c0000 {
+				label = "SBL3";
+				reg = <0x02c0000 0x0280000>;
+				read-only;
+			};
+
+			partition@540000 {
+				label = "DDRCONFIG";
+				reg = <0x0540000 0x0120000>;
+				read-only;
+			};
+
+			partition@660000 {
+				label = "SSD";
+				reg = <0x0660000 0x0120000>;
+				read-only;
+			};
+
+			partition@780000 {
+				label = "TZ";
+				reg = <0x0780000 0x0280000>;
+				read-only;
+			};
+
+			partition@a00000 {
+				label = "RPM";
+				reg = <0x0a00000 0x0280000>;
+				read-only;
+			};
+
+			art: partition@c80000 {
+				label = "art";
+				reg = <0x0c80000 0x0140000>;
+				read-only;
+			};
+
+			partition@dc0000 {
+				label = "APPSBL";
+				reg = <0x0dc0000 0x0100000>;
+				read-only;
+			};
+
+			partition@ec0000 {
+				label = "u_env";
+				reg = <0x0ec0000 0x0040000>;
+			};
+
+			partition@f00000 {
+				label = "s_env";
+				reg = <0x0f00000 0x0040000>;
+			};
+
+			partition@f40000 {
+				label = "devinfo";
+				reg = <0x0f40000 0x0040000>;
+			};
+
+			partition@f80000 {
+				label = "kernel1";
+				reg = <0x0f80000 0x2800000>;  /* 3 MB spill to rootfs */
+			};
+
+			partition@1280000 {
+				label = "rootfs1";
+				reg = <0x1280000 0x2500000>;
+			};
+
+			partition@3780000 {
+				label = "kernel2";
+				reg = <0x3780000 0x2800000>;
+			};
+
+			partition@3a80000 {
+				label = "rootfs2";
+				reg = <0x3a80000 0x2500000>;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x80        /* PAD6_MODE */
+			0x00010 0x2613a0    /* PWS_REG */
+			0x000e4 0x6a545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+			>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts
new file mode 100644
index 0000000000..ed8ab3dbfa
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts
@@ -0,0 +1,291 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "Netgear Nighthawk X4 R7500";
+	compatible = "netgear,r7500", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0xe000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power_white;
+		led-failsafe = &power_amber;
+		led-running = &power_white;
+		led-upgrade = &power_amber;
+	};
+
+	chosen {
+		bootargs = "rootfstype=squashfs noinitrd";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		usb1 {
+			label = "white:usb1";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb2 {
+			label = "white:usb2";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_amber: power_amber {
+			label = "amber:power";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_white {
+			label = "white:wan";
+			gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_amber {
+			label = "amber:wan";
+			gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		wps {
+			label = "white:wps";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+		};
+
+		esata {
+			label = "white:esata";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_white: power_white {
+			label = "white:power";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		wifi {
+			label = "white:wifi";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&qcom_pinmux {
+	button_pins: button_pins {
+		mux {
+			pins = "gpio6", "gpio54", "gpio65";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+				"gpio24","gpio26", "gpio53", "gpio64";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&gsbi5 {
+	status = "disabled";
+
+	spi@1a280000 {
+		status = "disabled";
+	};
+};
+
+&usb3_0 {
+	clocks = <&gcc USB30_1_MASTER_CLK>;
+	status = "okay";
+};
+
+&usb3_1 {
+	clocks = <&gcc USB30_0_MASTER_CLK>;
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+	max-link-speed = <1>;
+};
+
+&nand_controller {
+	status = "okay";
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+
+	nand@0 {
+		reg = <0>;
+		compatible = "qcom,nandcs";
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qcadata@0 {
+				label = "qcadata";
+				reg = <0x0000000 0x0c80000>;
+				read-only;
+			};
+
+			APPSBL@c80000 {
+				label = "APPSBL";
+				reg = <0x0c80000 0x0500000>;
+				read-only;
+			};
+
+			APPSBLENV@1180000 {
+				label = "APPSBLENV";
+				reg = <0x1180000 0x0080000>;
+				read-only;
+			};
+
+			art: art@1200000 {
+				label = "art";
+				reg = <0x1200000 0x0140000>;
+				read-only;
+			};
+
+			kernel@1340000 {
+				label = "kernel";
+				reg = <0x1340000 0x0400000>;
+			};
+
+			ubi@1740000 {
+				label = "ubi";
+				reg = <0x1740000 0x1600000>;
+			};
+
+			netgear@2d40000 {
+				label = "netgear";
+				reg = <0x2d40000 0x0c00000>;
+				read-only;
+			};
+
+			reserve@3940000 {
+				label = "reserve";
+				reg = <0x3940000 0x46c0000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x80        /* PAD6_MODE */
+			0x000e4 0x6a545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+			>;
+	};
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	mtd-mac-address = <&art 6>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+
+	mtd-mac-address = <&art 0>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&tcsr {
+	qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
+	compatible = "qcom,tcsr";
+};
+
+&adm_dma {
+	status = "okay";
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts
new file mode 100644
index 0000000000..20a1fad7b2
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts
@@ -0,0 +1,312 @@
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear Nighthawk X4 R7500v2";
+	compatible = "netgear,r7500v2", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		rsvd@5fe00000 {
+			reg = <0x5fe00000 0x200000>;
+			reusable;
+		};
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power;
+		led-failsafe = &power;
+		led-running = &power;
+		led-upgrade = &power;
+	};
+
+	chosen {
+		bootargs = "rootfstype=squashfs noinitrd";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		usb1 {
+			label = "amber:usb1";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb3 {
+			label = "amber:usb3";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		status {
+			label = "amber:status";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		internet {
+			label = "white:internet";
+			gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan {
+			label = "white:wan";
+			gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		wps {
+			label = "white:wps";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+		};
+
+		esata {
+			label = "white:esata";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		power: power {
+			label = "white:power";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		wifi {
+			label = "white:wifi";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
+
+&qcom_pinmux {
+	button_pins: button_pins {
+		mux {
+			pins = "gpio6", "gpio54", "gpio65";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+				"gpio24","gpio26", "gpio53", "gpio64";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	usb0_pwr_en_pins: usb0_pwr_en_pins {
+		mux {
+			pins = "gpio15";
+			function = "gpio";
+			drive-strength = <12>;
+			bias-pull-down;
+			output-high;
+		};
+	};
+
+	usb1_pwr_en_pins: usb1_pwr_en_pins {
+		mux {
+			pins = "gpio16", "gpio68";
+			function = "gpio";
+			drive-strength = <12>;
+			bias-pull-down;
+			output-high;
+		};
+	};
+};
+
+&sata_phy {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&usb3_0 {
+	status = "okay";
+
+	pinctrl-0 = <&usb0_pwr_en_pins>;
+	pinctrl-names = "default";
+};
+
+&usb3_1 {
+	status = "okay";
+
+	pinctrl-0 = <&usb1_pwr_en_pins>;
+	pinctrl-names = "default";
+};
+
+&pcie0 {
+	status = "okay";
+	reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pcie0_pins>;
+	pinctrl-names = "default";
+};
+
+&pcie1 {
+	status = "okay";
+	reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pcie1_pins>;
+	pinctrl-names = "default";
+	max-link-speed = <1>;
+};
+
+&nand_controller {
+	status = "okay";
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+
+	nand@0 {
+		reg = <0>;
+		compatible = "qcom,nandcs";
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qcadata@0 {
+				label = "qcadata";
+				reg = <0x0000000 0x0c80000>;
+				read-only;
+			};
+
+			APPSBL@c80000 {
+				label = "APPSBL";
+				reg = <0x0c80000 0x0500000>;
+				read-only;
+			};
+
+			APPSBLENV@1180000 {
+				label = "APPSBLENV";
+				reg = <0x1180000 0x0080000>;
+				read-only;
+			};
+
+			art: art@1200000 {
+				label = "art";
+				reg = <0x1200000 0x0140000>;
+				read-only;
+			};
+
+			artbak: art@1340000 {
+				label = "artbak";
+				reg = <0x1340000 0x0140000>;
+				read-only;
+			};
+
+			kernel@1480000 {
+				label = "kernel";
+				reg = <0x1480000 0x0400000>;
+			};
+
+			ubi@1880000 {
+				label = "ubi";
+				reg = <0x1880000 0x6080000>;
+			};
+
+			reserve@7900000 {
+				label = "reserve";
+				reg = <0x7900000 0x0700000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x80        /* PAD6_MODE */
+			0x000e4 0xaa545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+			>;
+	};
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	mtd-mac-address = <&art 6>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+
+	mtd-mac-address = <&art 0>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
\ No newline at end of file
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi
new file mode 100644
index 0000000000..b9ee86a891
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi
@@ -0,0 +1,69 @@
+#include "qcom-ipq8064.dtsi"
+
+/ {
+	aliases {
+		serial0 = &gsbi4_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+};
+
+&gsbi4 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+
+	serial@16340000 {
+		status = "okay";
+	};
+	/*
+	* The i2c device on gsbi4 should not be enabled.
+	* On ipq806x designs gsbi4 i2c is meant for exclusive
+	* RPM usage. Turning this on in kernel manifests as
+	* i2c failure for the RPM.
+	*/
+};
+
+&CPU_SPC {
+	status = "okay";
+};
+
+&pcie0 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie1 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie2 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&sata {
+	ports-implemented = <0x1>;
+};
+
+&ss_phy_0 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
+
+&ss_phy_1 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts
new file mode 100644
index 0000000000..ea7d0235ce
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts
@@ -0,0 +1,340 @@
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "TP-Link Archer VR2600v";
+	compatible = "tplink,vr2600v", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power;
+		led-failsafe = &general;
+		led-running = &power;
+		led-upgrade = &general;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		dect {
+			label = "dect";
+			gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PHONE>;
+		};
+
+		ledswitch {
+			label = "ledswitch";
+			gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LIGHTS_TOGGLE>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		dsl {
+			label = "white:dsl";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb {
+			label = "white:usb";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		lan {
+			label = "white:lan";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g {
+			label = "white:wlan2g";
+			gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g {
+			label = "white:wlan5g";
+			gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
+		};
+
+		power: power {
+			label = "white:power";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		phone {
+			label = "white:phone";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan {
+			label = "white:wan";
+			gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
+		};
+
+		general: general {
+			label = "white:general";
+			gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&qcom_pinmux {
+	led_pins: led_pins {
+		mux {
+			pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17",
+				"gpio26", "gpio53", "gpio56", "gpio66";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	button_pins: button_pins {
+		mux {
+			pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	spi_pins: spi_pins {
+		mux {
+			pins = "gpio18", "gpio19", "gpio21";
+			function = "gsbi5";
+			bias-pull-down;
+		};
+
+		data {
+			pins = "gpio18", "gpio19";
+			drive-strength = <10>;
+		};
+
+		cs {
+			pins = "gpio20";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+
+		clk {
+			pins = "gpio21";
+			drive-strength = <12>;
+		};
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	status = "okay";
+
+	spi4: spi@1a280000 {
+		status = "okay";
+
+		pinctrl-0 = <&spi_pins>;
+		pinctrl-names = "default";
+
+		cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+		W25Q128@0 {
+			compatible = "jedec,spi-nor";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			spi-max-frequency = <50000000>;
+			reg = <0>;
+
+			SBL1@0 {
+				label = "SBL1";
+				reg = <0x0 0x20000>;
+				read-only;
+			};
+
+			MIBIB@20000 {
+				label = "MIBIB";
+				reg = <0x20000 0x20000>;
+				read-only;
+			};
+
+			SBL2@40000 {
+				label = "SBL2";
+				reg = <0x40000 0x40000>;
+				read-only;
+			};
+
+			SBL3@80000 {
+				label = "SBL3";
+				reg = <0x80000 0x80000>;
+				read-only;
+			};
+
+			DDRCONFIG@100000 {
+				label = "DDRCONFIG";
+				reg = <0x100000 0x10000>;
+				read-only;
+			};
+
+			SSD@110000 {
+				label = "SSD";
+				reg = <0x110000 0x10000>;
+				read-only;
+			};
+
+			TZ@120000 {
+				label = "TZ";
+				reg = <0x120000 0x80000>;
+				read-only;
+			};
+
+			RPM@1a0000 {
+				label = "RPM";
+				reg = <0x1a0000 0x80000>;
+				read-only;
+			};
+
+			APPSBL@220000 {
+				label = "APPSBL";
+				reg = <0x220000 0x80000>;
+				read-only;
+			};
+
+			APPSBLENV@2a0000 {
+				label = "APPSBLENV";
+				reg = <0x2a0000 0x40000>;
+				read-only;
+			};
+
+			OLDART@2e0000 {
+				label = "OLDART";
+				reg = <0x2e0000 0x40000>;
+				read-only;
+			};
+
+			kernel@320000 {
+				label = "kernel";
+				reg = <0x320000 0x300000>;
+			};
+
+			rootfs@620000 {
+				label = "rootfs";
+				reg = <0x620000 0x960000>;
+			};
+
+			defaultmac: default-mac@0xfaf100 {
+				label = "default-mac";
+				reg = <0xfaf100 0x00200>;
+				read-only;
+			};
+
+			ART@fc0000 {
+				label = "ART";
+				reg = <0xfc0000 0x40000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+	max-link-speed = <1>;
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x80        /* PAD6_MODE */
+			0x000e4 0x6a545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+			>;
+	};
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	mtd-mac-address = <&defaultmac 0>;
+	mtd-mac-address-increment = <1>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+
+	mtd-mac-address = <&defaultmac 0>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts
new file mode 100644
index 0000000000..1a6b7eb4d6
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts
@@ -0,0 +1,370 @@
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "NEC Aterm WG2600HP";
+	compatible = "nec,wg2600hp", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power_green;
+		led-failsafe = &power_red;
+		led-running = &power_green;
+		led-upgrade = &power_green;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		bridge {
+			label = "bridge";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+		};
+
+		converter {
+			label = "converter";
+			gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		converter_green {
+			label = "green:converter";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_red: power_red {
+			label = "red:power";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		active_green {
+			label = "green:active";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		active_red {
+			label = "red:active";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_green: power_green {
+			label = "green:power";
+			gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		converter_red {
+			label = "red:converter";
+			gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g_green {
+			label = "green:wlan2g";
+			gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g_red {
+			label = "red:wlan2g";
+			gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g_green {
+			label = "green:wlan5g";
+			gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g_red {
+			label = "red:wlan5g";
+			gpios = <&qcom_pinmux 58 GPIO_ACTIVE_HIGH>;
+		};
+
+		tv_green {
+			label = "green:tv";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+
+		tv_red {
+			label = "red:tv";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x06000000  /* PAD0_MODE */
+			0x0000c 0x00080080  /* PAD6_MODE */
+			0x000e4 0x0006a545  /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x0000004e  /* PORT0_STATUS */
+			0x00094 0x0000004e  /* PORT6_STATUS */
+			>;
+	};
+
+	ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	mtd-mac-address = <&PRODUCTDATA 6>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+
+	mtd-mac-address = <&PRODUCTDATA 0>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gsbi5 {
+	status = "okay";
+
+	qcom,mode = <GSBI_PROT_SPI>;
+
+	spi@1a280000 {
+		status = "okay";
+
+		pinctrl-0 = <&spi_pins>;
+		pinctrl-names = "default";
+
+		cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+		flash@0 {
+			compatible = "jedec,spi-nor";
+			spi-max-frequency = <50000000>;
+			reg = <0>;
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				SBL1@0 {
+					label = "SBL1";
+					reg = <0x0 0x20000>;
+					read-only;
+				};
+
+				MIBIB@20000 {
+					label = "MIBIB";
+					reg = <0x20000 0x20000>;
+					read-only;
+				};
+
+				SBL2@40000 {
+					label = "SBL2";
+					reg = <0x40000 0x40000>;
+					read-only;
+				};
+
+				SBL3@80000 {
+					label = "SBL3";
+					reg = <0x80000 0x80000>;
+					read-only;
+				};
+
+				DDRCONFIG@100000 {
+					label = "DDRCONFIG";
+					reg = <0x100000 0x10000>;
+					read-only;
+				};
+
+				SSD@110000 {
+					label = "SSD";
+					reg = <0x110000 0x10000>;
+					read-only;
+				};
+
+				TZ@120000 {
+					label = "TZ";
+					reg = <0x120000 0x80000>;
+					read-only;
+				};
+
+				RPM@1a0000 {
+					label = "RPM";
+					reg = <0x1a0000 0x80000>;
+					read-only;
+				};
+
+				APPSBL@220000 {
+					label = "APPSBL";
+					reg = <0x220000 0x80000>;
+					read-only;
+				};
+
+				APPSBLENV@2a0000 {
+					label = "APPSBLENV";
+					reg = <0x2a0000 0x10000>;
+				};
+
+				PRODUCTDATA: PRODUCTDATA@2b0000 {
+					label = "PRODUCTDATA";
+					reg = <0x2b0000 0x30000>;
+					read-only;
+				};
+
+				ART@2e0000 {
+					label = "ART";
+					reg = <0x2e0000 0x40000>;
+					read-only;
+				};
+
+				TP@320000 {
+					label = "TP";
+					reg = <0x320000 0x40000>;
+					read-only;
+				};
+
+				TINY@360000 {
+					label = "TINY";
+					reg = <0x360000 0x500000>;
+					read-only;
+				};
+
+				firmware@860000 {
+					compatible = "denx,uimage";
+					label = "firmware";
+					reg = <0x860000 0x17a0000>;
+				};
+			};
+		};
+	};
+};
+
+&usb3_0 {
+	status = "okay";
+
+	pinctrl-0 = <&usb_pwr_en_pins>;
+	pinctrl-names = "default";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+	max-link-speed = <1>;
+};
+
+&qcom_pinmux {
+	button_pins: button_pins {
+		mux {
+			pins = "gpio16", "gpio54", "gpio24", "gpio25";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio14",
+				"gpio15", "gpio55", "gpio56", "gpio57", "gpio58",
+				"gpio64", "gpio65";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	spi_pins: spi_pins {
+		mux {
+			pins = "gpio18", "gpio19", "gpio21";
+			function = "gsbi5";
+			bias-pull-down;
+		};
+
+		data {
+			pins = "gpio18", "gpio19";
+			drive-strength = <10>;
+		};
+
+		cs {
+			pins = "gpio20";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+
+		clk {
+			pins = "gpio21";
+			drive-strength = <12>;
+		};
+	};
+
+	usb_pwr_en_pins: usb_pwr_en_pins {
+		mux {
+			pins = "gpio22";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+			output-high;
+		};
+	};
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts
new file mode 100644
index 0000000000..739b7261a3
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts
@@ -0,0 +1,486 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright (C) 2017 Christian Mehlis <christian@m3hlis.de>
+ *  Copyright (C) 2018 Mathias Kresin <dev@kresin.me>
+ *  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    1. Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *    2. Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *    3. Neither the names of the copyright holders nor the names of any
+ *       contributors may be used to endorse or promote products derived
+ *       from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	compatible = "compex,wpq864", "qcom,ipq8064";
+	model = "Compex WPQ864";
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+		ethernet0 = &gmac1;
+		ethernet1 = &gmac0;
+
+		led-boot = &led_pass;
+		led-failsafe = &led_fail;
+		led-running = &led_pass;
+		led-upgrade = &led_pass;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		rss4 {
+			label = "green:rss4";
+			gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		rss3 {
+			label = "green:rss3";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		rss2 {
+			label = "orange:rss2";
+			gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
+		};
+
+		rss1 {
+			label = "red:rss1";
+			gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_pass: pass {
+			label = "green:pass";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_fail: fail {
+			label = "green:fail";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb {
+			label = "green:usb";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb-pcie {
+			label = "green:usb-pcie";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	beeper {
+		compatible = "gpio-beeper";
+
+		pinctrl-0 = <&beeper_pins>;
+		pinctrl-names = "default";
+
+		gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&rpm {
+	pinctrl-0 = <&rpm_pins>;
+	pinctrl-names = "default";
+};
+
+&nand_controller {
+	status = "okay";
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+
+	mt29f2g08abbeah4@0 {
+		compatible = "qcom,nandcs";
+
+		reg = <0>;
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			SBL1@0 {
+				label = "SBL1";
+				reg = <0x0000000 0x0040000>;
+				read-only;
+			};
+
+			MIBIB@40000 {
+				label = "MIBIB";
+				reg = <0x0040000 0x0140000>;
+				read-only;
+			};
+
+			SBL2@180000 {
+				label = "SBL2";
+				reg = <0x0180000 0x0140000>;
+				read-only;
+			};
+
+			SBL3@2c0000 {
+				label = "SBL3";
+				reg = <0x02c0000 0x0280000>;
+				read-only;
+			};
+
+			DDRCONFIG@540000 {
+				label = "DDRCONFIG";
+				reg = <0x0540000 0x0120000>;
+				read-only;
+			};
+
+			SSD@660000 {
+				label = "SSD";
+				reg = <0x0660000 0x0120000>;
+				read-only;
+			};
+
+			TZ@780000 {
+				label = "TZ";
+				reg = <0x0780000 0x0280000>;
+				read-only;
+			};
+
+			RPM@a00000 {
+				label = "RPM";
+				reg = <0x0a00000 0x0280000>;
+				read-only;
+			};
+
+			APPSBL@c80000 {
+				label = "APPSBL";
+				reg = <0x0c80000 0x0500000>;
+				read-only;
+			};
+
+			APPSBLENV@1180000 {
+				label = "APPSBLENV";
+				reg = <0x1180000 0x0080000>;
+			};
+
+			ART@1200000 {
+				label = "ART";
+				reg = <0x1200000 0x0140000>;
+			};
+
+			ubi@1340000 {
+				label = "ubi";
+				reg = <0x1340000 0x4000000>;
+			};
+
+			BOOTCONFIG@5340000 {
+				label = "BOOTCONFIG";
+				reg = <0x5340000 0x0060000>;
+			};
+
+			SBL2-1@53a0000- {
+				label = "SBL2_1";
+				reg = <0x53a0000 0x0140000>;
+				read-only;
+			};
+
+			SBL3-1@54e0000 {
+				label = "SBL3_1";
+				reg = <0x54e0000 0x0280000>;
+				read-only;
+			};
+
+			DDRCONFIG-1@5760000 {
+				label = "DDRCONFIG_1";
+				reg = <0x5760000 0x0120000>;
+				read-only;
+			};
+
+			SSD-1@5880000 {
+				label = "SSD_1";
+				reg = <0x5880000 0x0120000>;
+				read-only;
+			};
+
+			TZ-1@59a0000 {
+				label = "TZ_1";
+				reg = <0x59a0000 0x0280000>;
+				read-only;
+			};
+
+			RPM-1@5c20000 {
+				label = "RPM_1";
+				reg = <0x5c20000 0x0280000>;
+				read-only;
+			};
+
+			BOOTCONFIG1@5ea0000 {
+				label = "BOOTCONFIG1";
+				reg = <0x5ea0000 0x0060000>;
+			};
+
+			APPSBL-1@5f00000 {
+				label = "APPSBL_1";
+				reg = <0x5f00000 0x0500000>;
+				read-only;
+			};
+
+			ubi-1@6400000 {
+				label = "ubi_1";
+				reg = <0x6400000 0x4000000>;
+			};
+
+			unused@a400000 {
+				label = "unused";
+				reg = <0xa400000 0x5c00000>;
+			};
+		};
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x80        /* PAD6_MODE */
+			0x000e4 0x6a545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+			>;
+	};
+
+	ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gsbi4_serial {
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+};
+
+&flash {
+	compatible = "jedec,spi-nor";
+};
+
+&sata_phy {
+	status = "disabled";
+};
+
+&sata {
+	status = "disabled";
+};
+
+&ss_phy_0 {		/* USB3 port 0 SS phy */
+	status = "okay";
+
+	rx_eq = <2>;
+	tx_deamp_3_5db = <32>;
+	mpll = <160>;
+};
+
+&ss_phy_1 {		/* USB3 port 1 SS phy */
+	status = "okay";
+
+	rx_eq = <2>;
+	tx_deamp_3_5db = <32>;
+	mpll = <160>;
+};
+
+&pcie0 {
+	status = "okay";
+
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+	/delete-property/ perst-gpios;
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pcie2 {
+	status = "okay";
+
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+	/delete-property/ perst-gpios;
+};
+
+&qcom_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&state_default>;
+
+	state_default: pinctrl0 {
+		pcie0_pcie2_perst {
+			pins = "gpio3";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio7", "gpio8", "gpio9", "gpio22",
+			       "gpio23", "gpio24", "gpio25", "gpio53";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	button_pins: button_pins {
+		mux {
+			pins = "gpio54";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	beeper_pins: beeper_pins {
+		mux {
+			pins = "gpio55";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	rpm_pins: rpm_pins {
+		mux {
+			pins = "gpio12", "gpio13";
+			function = "gsbi4";
+			drive-strength = <10>;
+			bias-disable;
+		};
+	};
+
+	uart0_pins: uart0_pins {
+		mux {
+			pins = "gpio10", "gpio11";
+			function = "gsbi4";
+			drive-strength = <10>;
+			bias-disable;
+		};
+	};
+
+	spi_pins: spi_pins {
+		mux {
+			pins = "gpio18", "gpio19";
+			function = "gsbi5";
+			drive-strength = <10>;
+			bias-pull-down;
+		};
+
+		clk {
+			pins = "gpio21";
+			function = "gsbi5";
+			drive-strength = <12>;
+			bias-pull-down;
+		};
+
+		cs {
+			pins = "gpio20";
+			function = "gpio";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&tcsr {
+	qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts
new file mode 100644
index 0000000000..d80bfa204d
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Buffalo WXR-2533DHP";
+	compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064";
+
+	memory@42000000 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	aliases {
+		led-boot = &power;
+		led-failsafe = &diag;
+		led-running = &power;
+		led-upgrade = &power;
+	};
+
+	chosen {
+		/* use "ubi_rootfs" volume in "ubi" partition as rootfs */
+		bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		usb {
+			label = "green:usb";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usbport";
+			trigger-sources = <&hub_port0 &hub_port1>;
+		};
+
+		guestport {
+			label = "green:guestport";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		diag: diag {
+			label = "orange:diag";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		internet_orange {
+			label = "orange:internet";
+			gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
+		};
+
+		internet_white {
+			label = "white:internet";
+			gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		wireless_orange {
+			label = "orange:wireless";
+			gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		wireless_white {
+			label = "white:wireless";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+		};
+
+		router_orange {
+			label = "orange:router";
+			gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
+		};
+
+		router_white {
+			label = "white:router";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
+		};
+
+		power: power {
+			label = "white:power";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		power {
+			label = "power";
+			gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		eject {
+			label = "eject";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_EJECTCD>;
+		};
+
+		guest {
+			label = "guest";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		ap {
+			label = "ap";
+			gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_1>;
+			linux,input-type = <EV_SW>;
+		};
+
+		router {
+			label = "router";
+			gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_1>;
+			linux,input-type = <EV_SW>;
+		};
+
+		auto {
+			label = "auto";
+			gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_1>;
+			linux,input-type = <EV_SW>;
+		};
+	};
+};
+
+&nand_controller {
+	status = "okay";
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+
+	cs@0 {
+		reg = <0>;
+		compatible = "qcom,nandcs";
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ubi@0 {
+				label = "ubi";
+				reg = <0x0000000 0x4000000>;
+			};
+
+			rootfs_1@4000000 {
+				label = "rootfs_1";
+				reg = <0x4000000 0x4000000>;
+			};
+		};
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x07600000  /* PAD0_MODE */
+			0x00008 0x01000000  /* PAD5_MODE */
+			0x0000c 0x00000080  /* PAD6_MODE */
+			0x00050 0xcc35cc35  /* LED_CTRL0 */
+			0x00054 0xca35ca35  /* LED_CTRL1 */
+			0x00058 0xc935c935  /* LED_CTRL2 */
+			0x0005c 0x03ffff00  /* LED_CTRL3 */
+			0x000e4 0x0006a545  /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x0000007e  /* PORT0_STATUS */
+			0x00094 0x0000007e  /* PORT6_STATUS */
+			>;
+	};
+
+	ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	mtd-mac-address = <&ART 6>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+
+	mtd-mac-address = <&ART 0>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gsbi4_serial {
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+};
+
+&gsbi5 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_SPI>;
+
+	spi@1a280000 {
+		status = "okay";
+
+		pinctrl-0 = <&spi_pins>;
+		pinctrl-names = "default";
+
+		cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+		flash@0 {
+			compatible = "jedec,spi-nor";
+			spi-max-frequency = <50000000>;
+			reg = <0>;
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				SBL1@0 {
+					label = "SBL1";
+					reg = <0x0 0x10000>;
+					read-only;
+				};
+
+				MIBIB@10000 {
+					label = "MIBIB";
+					reg = <0x10000 0x20000>;
+					read-only;
+				};
+
+				SBL2@30000 {
+					label = "SBL2";
+					reg = <0x30000 0x30000>;
+					read-only;
+				};
+
+				SBL3@60000 {
+					label = "SBL3";
+					reg = <0x60000 0x30000>;
+					read-only;
+				};
+
+				DDRCONFIG@90000 {
+					label = "DDRCONFIG";
+					reg = <0x90000 0x10000>;
+					read-only;
+				};
+
+				SSD@a0000 {
+					label = "SSD";
+					reg = <0xa0000 0x10000>;
+					read-only;
+				};
+
+				TZ@b0000 {
+					label = "TZ";
+					reg = <0xb0000 0x30000>;
+					read-only;
+				};
+
+				RPM@e0000 {
+					label = "RPM";
+					reg = <0xe0000 0x20000>;
+					read-only;
+				};
+
+				APPSBL@100000 {
+					label = "APPSBL";
+					reg = <0x100000 0x70000>;
+					read-only;
+				};
+
+				APPSBLENV@170000 {
+					label = "APPSBLENV";
+					reg = <0x170000 0x10000>;
+					read-only;
+				};
+
+				ART: ART@180000 {
+					label = "ART";
+					reg = <0x180000 0x40000>;
+					read-only;
+				};
+
+				BOOTCONFIG@1c0000 {
+					label = "BOOTCONFIG";
+					reg = <0x1c0000 0x10000>;
+					read-only;
+				};
+
+				APPSBL_1@1d0000 {
+					label = "APPSBL_1";
+					reg = <0x1d0000 0x70000>;
+					read-only;
+				};
+			};
+		};
+	};
+};
+
+&usb3_0 {
+	status = "okay";
+
+	pinctrl-0 = <&usb_pwr_en_pins>;
+	pinctrl-names = "default";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&dwc3_0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub_port0: port@1 {
+		reg = <1>;
+		#trigger-source-cells = <0>;
+	};
+};
+
+&dwc3_1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub_port1: port@1 {
+		reg = <1>;
+		#trigger-source-cells = <0>;
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+	max-link-speed = <1>;
+};
+
+&qcom_pinmux {
+	button_pins: button_pins {
+		mux {
+			pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57",
+				"gpio58", "gpio64", "gpio65";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22",
+				"gpio23", "gpio24", "gpio25", "gpio26", "gpio53";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	uart0_pins: uart0_pins {
+		mux {
+			pins = "gpio10", "gpio11";
+			function = "gsbi4";
+			drive-strength = <12>;
+			bias-disable;
+		};
+	};
+
+	spi_pins: spi_pins {
+		mux {
+			pins = "gpio18", "gpio19", "gpio21";
+			function = "gsbi5";
+			bias-pull-down;
+		};
+
+		data {
+			pins = "gpio18", "gpio19";
+			drive-strength = <10>;
+		};
+
+		cs{
+			pins = "gpio20";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+
+		clk {
+			pins = "gpio21";
+			drive-strength = <12>;
+		};
+	};
+
+	usb_pwr_en_pins: usb_pwr_en_pins {
+		mux{
+			pins = "gpio68";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+			output-high;
+		};
+	};
+};
\ No newline at end of file
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
new file mode 100644
index 0000000000..2573349f55
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
@@ -0,0 +1,310 @@
+#include "qcom-ipq8065.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "ZyXEL NBG6817";
+	compatible = "zyxel,nbg6817", "qcom,ipq8065", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+		sdcc1 = &sdcc1;
+
+		led-boot = &power;
+		led-failsafe = &power;
+		led-running = &power;
+		led-upgrade = &power;
+	};
+
+	chosen {
+		bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd";
+		append-rootblock = "root=/dev/mmcblk0p";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+			linux,input-type = <EV_SW>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		internet {
+			label = "white:internet";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+
+		power: power {
+			label = "white:power";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		wifi2g {
+			label = "amber:wifi2g";
+			gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
+		};
+
+		/* wifi2g amber from the manual is missing */
+
+		wifi5g {
+			label = "amber:wifi5g";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		/* wifi5g amber from the manual is missing */
+	};
+};
+
+&qcom_pinmux {
+	button_pins: button_pins {
+		mux {
+			pins = "gpio53", "gpio54", "gpio65";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio9", "gpio26", "gpio33", "gpio64";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	mdio0_pins: mdio0_pins {
+		clk {
+			pins = "gpio1";
+			input-disable;
+		};
+	};
+
+	rgmii2_pins: rgmii2_pins {
+		tx {
+			pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
+			input-disable;
+		};
+	};
+
+	spi_pins: spi_pins {
+		cs {
+			pins = "gpio20";
+			drive-strength = <12>;
+		};
+	};
+
+	usb0_pwr_en_pins: usb0_pwr_en_pins {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "gpio";
+			drive-strength = <12>;
+		};
+
+		pwr {
+			pins = "gpio17";
+			bias-pull-down;
+			output-high;
+		};
+
+		ovc {
+			pins = "gpio16";
+			bias-pull-up;
+		};
+	};
+
+	usb1_pwr_en_pins: usb1_pwr_en_pins {
+		mux {
+			pins = "gpio14", "gpio15";
+			function = "gpio";
+			drive-strength = <12>;
+		};
+
+		pwr {
+			pins = "gpio14";
+			bias-pull-down;
+			output-high;
+		};
+
+		ovc {
+			pins = "gpio15";
+			bias-pull-up;
+		};
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	status = "okay";
+
+	spi4: spi@1a280000 {
+		status = "okay";
+
+		pinctrl-0 = <&spi_pins>;
+		pinctrl-names = "default";
+
+		cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+		m25p80@0 {
+			compatible = "jedec,spi-nor";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			spi-max-frequency = <51200000>;
+			reg = <0>;
+
+			partitions {
+				compatible = "qcom,smem";
+			};
+		};
+	};
+};
+
+&usb3_0 {
+	status = "okay";
+
+	pinctrl-0 = <&usb0_pwr_en_pins>;
+	pinctrl-names = "default";
+};
+
+&usb3_1 {
+	status = "okay";
+
+	pinctrl-0 = <&usb1_pwr_en_pins>;
+	pinctrl-names = "default";
+};
+
+&pcie0 {
+	status = "okay";
+	reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pcie0_pins>;
+	pinctrl-names = "default";
+};
+
+&pcie1 {
+	status = "okay";
+	reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pcie1_pins>;
+	pinctrl-names = "default";
+	max-link-speed = <1>;
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x80        /* PAD6_MODE */
+			0x000e4 0xaa545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+			0x00970 0x1e864443  /* QM_PORT0_CTRL0 */
+			0x00974 0x000001c6  /* QM_PORT0_CTRL1 */
+			0x00978 0x19008643  /* QM_PORT1_CTRL0 */
+			0x0097c 0x000001c6  /* QM_PORT1_CTRL1 */
+			0x00980 0x19008643  /* QM_PORT2_CTRL0 */
+			0x00984 0x000001c6  /* QM_PORT2_CTRL1 */
+			0x00988 0x19008643  /* QM_PORT3_CTRL0 */
+			0x0098c 0x000001c6  /* QM_PORT3_CTRL1 */
+			0x00990 0x19008643  /* QM_PORT4_CTRL0 */
+			0x00994 0x000001c6  /* QM_PORT4_CTRL1 */
+			0x00998 0x1e864443  /* QM_PORT5_CTRL0 */
+			0x0099c 0x000001c6  /* QM_PORT5_CTRL1 */
+			0x009a0 0x1e864443  /* QM_PORT6_CTRL0 */
+			0x009a4 0x000001c6  /* QM_PORT6_CTRL1 */
+			>;
+	};
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+		qca,ar8327-initvals = <
+			0x000e4 0x6a545     /* MAC_POWER_SEL */
+			0x0000c 0x80        /* PAD6_MODE */
+			>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+	qcom,phy_mdio_addr = <4>;
+	qcom,poll_required = <0>;
+	qcom,rgmii_delay = <1>;
+	qcom,phy_mii_type = <0>;
+	qcom,emulation = <0>;
+	qcom,irq = <255>;
+	mdiobus = <&mdio0>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+	qcom,phy_mdio_addr = <0>;	/* none */
+	qcom,poll_required = <0>;	/* no polling */
+	qcom,rgmii_delay = <0>;
+	qcom,phy_mii_type = <1>;
+	qcom,emulation = <0>;
+	qcom,irq = <258>;
+	mdiobus = <&mdio0>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&amba {
+	sdcc1: sdcc@12400000 {
+		status = "okay";
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-r7800.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-r7800.dts
new file mode 100644
index 0000000000..181f6d3bde
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-r7800.dts
@@ -0,0 +1,449 @@
+#include "qcom-ipq8065.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear Nighthawk X4S R7800";
+	compatible = "netgear,r7800", "qcom,ipq8065", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		rsvd@5fe00000 {
+			reg = <0x5fe00000 0x200000>;
+			reusable;
+		};
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power_white;
+		led-failsafe = &power_amber;
+		led-running = &power_white;
+		led-upgrade = &power_amber;
+		label-mac-device = &gmac2;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+			debounce-interval = <60>;
+			wakeup-source;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+			debounce-interval = <60>;
+			wakeup-source;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+			debounce-interval = <60>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		power_white: power_white {
+			label = "white:power";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		power_amber: power_amber {
+			label = "amber:power";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_white {
+			label = "white:wan";
+			gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_amber {
+			label = "amber:wan";
+			gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb1 {
+			label = "white:usb1";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb2 {
+			label = "white:usb2";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		esata {
+			label = "white:esata";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		wifi {
+			label = "white:wifi";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+
+		wps {
+			label = "white:wps";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&qcom_pinmux {
+	button_pins: button_pins {
+		mux {
+			pins = "gpio6", "gpio54", "gpio65";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+				"gpio24","gpio26", "gpio53", "gpio64";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	mdio0_pins: mdio0_pins {
+		clk {
+			pins = "gpio1";
+			input-disable;
+		};
+	};
+
+	rgmii2_pins: rgmii2_pins {
+		tx {
+			pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
+			input-disable;
+		};
+	};
+
+	spi_pins: spi_pins {
+		mux {
+			pins = "gpio18", "gpio19", "gpio21";
+			function = "gsbi5";
+			bias-pull-down;
+		};
+
+		data {
+			pins = "gpio18", "gpio19";
+			drive-strength = <10>;
+		};
+
+		cs {
+			pins = "gpio20";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+
+		clk {
+			pins = "gpio21";
+			drive-strength = <12>;
+		};
+	};
+
+	spi6_pins: spi6_pins {
+		mux {
+			pins = "gpio55", "gpio56", "gpio58";
+			function = "gsbi6";
+			bias-pull-down;
+		};
+
+		mosi {
+			pins = "gpio55";
+			drive-strength = <12>;
+		};
+
+		miso {
+			pins = "gpio56";
+			drive-strength = <14>;
+		};
+
+		cs {
+			pins = "gpio57";
+			drive-strength = <12>;
+			bias-pull-up;
+		};
+
+		clk {
+			pins = "gpio58";
+			drive-strength = <12>;
+		};
+
+		reset {
+			pins = "gpio33";
+			drive-strength = <10>;
+			bias-pull-down;
+			output-high;
+		};
+	};
+
+	usb0_pwr_en_pins: usb0_pwr_en_pins {
+		mux {
+			pins = "gpio15";
+			function = "gpio";
+			drive-strength = <12>;
+			bias-pull-down;
+			output-high;
+		};
+	};
+
+	usb1_pwr_en_pins: usb1_pwr_en_pins {
+		mux {
+			pins = "gpio16", "gpio68";
+			function = "gpio";
+			drive-strength = <12>;
+			bias-pull-down;
+			output-high;
+		};
+	};
+};
+
+&nand_controller {
+	status = "okay";
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+
+	nand@0 {
+		reg = <0>;
+		compatible = "qcom,nandcs";
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qcadata@0 {
+				label = "qcadata";
+				reg = <0x0000000 0x0c80000>;
+				read-only;
+			};
+
+			APPSBL@c80000 {
+				label = "APPSBL";
+				reg = <0x0c80000 0x0500000>;
+				read-only;
+			};
+
+			APPSBLENV@1180000 {
+				label = "APPSBLENV";
+				reg = <0x1180000 0x0080000>;
+				read-only;
+			};
+
+			art: art@1200000 {
+				label = "art";
+				reg = <0x1200000 0x0140000>;
+				read-only;
+			};
+
+			artbak: art@1340000 {
+				label = "artbak";
+				reg = <0x1340000 0x0140000>;
+				read-only;
+			};
+
+			kernel@1480000 {
+				label = "kernel";
+				reg = <0x1480000 0x0400000>;
+			};
+
+			ubi@1880000 {
+				label = "ubi";
+				reg = <0x1880000 0x6080000>;
+			};
+
+			reserve@7900000 {
+				label = "reserve";
+				reg = <0x7900000 0x0700000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-0 = <&mdio0_pins>;
+	pinctrl-names = "default";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+			0x00004 0x7600000   /* PAD0_MODE */
+			0x00008 0x1000000   /* PAD5_MODE */
+			0x0000c 0x80        /* PAD6_MODE */
+			0x000e4 0xaa545     /* MAC_POWER_SEL */
+			0x000e0 0xc74164de  /* SGMII_CTRL */
+			0x0007c 0x4e        /* PORT0_STATUS */
+			0x00094 0x4e        /* PORT6_STATUS */
+			0x00970 0x1e864443  /* QM_PORT0_CTRL0 */
+			0x00974 0x000001c6  /* QM_PORT0_CTRL1 */
+			0x00978 0x19008643  /* QM_PORT1_CTRL0 */
+			0x0097c 0x000001c6  /* QM_PORT1_CTRL1 */
+			0x00980 0x19008643  /* QM_PORT2_CTRL0 */
+			0x00984 0x000001c6  /* QM_PORT2_CTRL1 */
+			0x00988 0x19008643  /* QM_PORT3_CTRL0 */
+			0x0098c 0x000001c6  /* QM_PORT3_CTRL1 */
+			0x00990 0x19008643  /* QM_PORT4_CTRL0 */
+			0x00994 0x000001c6  /* QM_PORT4_CTRL1 */
+			0x00998 0x1e864443  /* QM_PORT5_CTRL0 */
+			0x0099c 0x000001c6  /* QM_PORT5_CTRL1 */
+			0x009a0 0x1e864443  /* QM_PORT6_CTRL0 */
+			0x009a4 0x000001c6  /* QM_PORT6_CTRL1 */
+			>;
+		qca,ar8327-vlans = <
+			0x1	0x5e	    /* VLAN1 Ports 1/2/3/4/6 */
+			0x2	0x21	    /* VLAN2 Ports 0/5 */
+		>;
+	};
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+		qca,ar8327-initvals = <
+			0x000e4 0x6a545     /* MAC_POWER_SEL */
+			0x0000c 0x80        /* PAD6_MODE */
+			>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	qcom,id = <1>;
+	qcom,phy_mdio_addr = <4>;
+	qcom,poll_required = <0>;
+	qcom,rgmii_delay = <1>;
+	qcom,phy_mii_type = <0>;
+	qcom,emulation = <0>;
+	qcom,irq = <255>;
+	mdiobus = <&mdio0>;
+
+	pinctrl-0 = <&rgmii2_pins>;
+	pinctrl-names = "default";
+
+	mtd-mac-address = <&art 6>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "sgmii";
+	qcom,id = <2>;
+	qcom,phy_mdio_addr = <0>;	/* none */
+	qcom,poll_required = <0>;	/* no polling */
+	qcom,rgmii_delay = <0>;
+	qcom,phy_mii_type = <1>;
+	qcom,emulation = <0>;
+	qcom,irq = <258>;
+	mdiobus = <&mdio0>;
+
+	mtd-mac-address = <&art 0>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
+
+&sata_phy {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&usb3_0 {
+	status = "okay";
+	
+	pinctrl-0 = <&usb0_pwr_en_pins>;
+	pinctrl-names = "default";
+};
+
+&usb3_1 {
+	status = "okay";
+	
+	pinctrl-0 = <&usb1_pwr_en_pins>;
+	pinctrl-names = "default";
+};
+
+&pcie0 {
+	status = "okay";
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi@1,0 {
+			compatible = "pci168c,0046";
+			reg = <0x00010000 0 0 0 0>;
+
+			mtd-mac-address = <&art 6>;
+			mtd-mac-address-increment = <(1)>;
+		};
+	};
+};
+
+&pcie1 {
+	status = "okay";
+	max-link-speed = <1>;
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi@1,0 {
+			compatible = "pci168c,0046";
+			reg = <0x00010000 0 0 0 0>;
+
+			mtd-mac-address = <&art 6>;
+			mtd-mac-address-increment = <(2)>;
+		};
+	};
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065.dtsi b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065.dtsi
new file mode 100644
index 0000000000..ab67d504e6
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065.dtsi
@@ -0,0 +1,157 @@
+#include "qcom-ipq8064.dtsi"
+
+/ {
+	model = "Qualcomm IPQ8065";
+	compatible = "qcom,ipq8065", "qcom,ipq8064";
+
+	aliases {
+		serial0 = &gsbi4_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cpus {
+		qcom,l2 {
+			qcom,l2-cpufreq = <384000000 600000000 1400000000>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+};
+
+&gsbi4 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+
+	serial@16340000 {
+		status = "okay";
+	};
+	/*
+	* The i2c device on gsbi4 should not be enabled.
+	* On ipq806x designs gsbi4 i2c is meant for exclusive
+	* RPM usage. Turning this on in kernel manifests as
+	* i2c failure for the RPM.
+	*/
+};
+
+&pcie0 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie1 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie2 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&sata {
+	ports-implemented = <0x1>;
+};
+
+&smb208_s2a {
+	regulator-min-microvolt = <775000>;
+	regulator-max-microvolt = <1275000>;
+};
+
+&smb208_s2b {
+	regulator-min-microvolt = <775000>;
+	regulator-max-microvolt = <1275000>;
+};
+
+&ss_phy_0 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
+
+&ss_phy_1 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
+
+&opp_table0 {
+	/* 
+	 * On ipq8065 1.2 ghz freq is not present
+	 * Remove it to make cpufreq work and not
+	 * complain for missing definition
+	 */
+
+	/delete-node/opp-1200000000;
+
+	opp-384000000 {
+		opp-microvolt-speed0-pvs0-v0 = <975000>;
+		opp-microvolt-speed0-pvs1-v0 = <950000>;
+		opp-microvolt-speed0-pvs2-v0 = <925000>;
+		opp-microvolt-speed0-pvs3-v0 = <900000>;
+		opp-microvolt-speed0-pvs4-v0 = <875000>;
+		opp-microvolt-speed0-pvs5-v0 = <825000>;
+		opp-microvolt-speed0-pvs6-v0 = <775000>;
+	};
+
+	opp-600000000 {
+		opp-microvolt-speed0-pvs0-v0 = <1000000>;
+		opp-microvolt-speed0-pvs1-v0 = <975000>;
+		opp-microvolt-speed0-pvs2-v0 = <950000>;
+		opp-microvolt-speed0-pvs3-v0 = <925000>;
+		opp-microvolt-speed0-pvs4-v0 = <900000>;
+		opp-microvolt-speed0-pvs5-v0 = <850000>;
+		opp-microvolt-speed0-pvs6-v0 = <800000>;
+	};
+
+	opp-800000000 {
+		opp-microvolt-speed0-pvs0-v0 = <1050000>;
+		opp-microvolt-speed0-pvs1-v0 = <1025000>;
+		opp-microvolt-speed0-pvs2-v0 = <1000000>;
+		opp-microvolt-speed0-pvs3-v0 = <975000>;
+		opp-microvolt-speed0-pvs4-v0 = <950000>;
+		opp-microvolt-speed0-pvs5-v0 = <900000>;
+		opp-microvolt-speed0-pvs6-v0 = <850000>;
+	};
+
+	opp-1000000000 {
+		opp-microvolt-speed0-pvs0-v0 = <1100000>;
+		opp-microvolt-speed0-pvs1-v0 = <1075000>;
+		opp-microvolt-speed0-pvs2-v0 = <1050000>;
+		opp-microvolt-speed0-pvs3-v0 = <1025000>;
+		opp-microvolt-speed0-pvs4-v0 = <1000000>;
+		opp-microvolt-speed0-pvs5-v0 = <950000>;
+		opp-microvolt-speed0-pvs6-v0 = <900000>;
+	};
+
+	opp-1400000000 {
+		opp-microvolt-speed0-pvs0-v0 = <1175000>;
+		opp-microvolt-speed0-pvs1-v0 = <1150000>;
+		opp-microvolt-speed0-pvs2-v0 = <1125000>;
+		opp-microvolt-speed0-pvs3-v0 = <1100000>;
+		opp-microvolt-speed0-pvs4-v0 = <1075000>;
+		opp-microvolt-speed0-pvs5-v0 = <1025000>;
+		opp-microvolt-speed0-pvs6-v0 = <975000>;
+	};
+
+	opp-1725000000 {
+		opp-hz = /bits/ 64 <1725000000>;
+		opp-microvolt-speed0-pvs0-v0 = <1262500>;
+		opp-microvolt-speed0-pvs1-v0 = <1225000>;
+		opp-microvolt-speed0-pvs2-v0 = <1200000>;
+		opp-microvolt-speed0-pvs3-v0 = <1175000>;
+		opp-microvolt-speed0-pvs4-v0 = <1150000>;
+		opp-microvolt-speed0-pvs5-v0 = <1100000>;
+		opp-microvolt-speed0-pvs6-v0 = <1050000>;
+		opp-supported-hw = <0x1>;
+		clock-latency-ns = <100000>;
+	};
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts
new file mode 100644
index 0000000000..712910c261
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts
@@ -0,0 +1,339 @@
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "Edgecore ECW5410";
+	compatible = "edgecore,ecw5410", "qcom,ipq8064";
+
+	reserved-memory {
+		nss@40000000 {
+			reg = <0x40000000 0x1000000>;
+			no-map;
+		};
+
+		smem: smem@41000000 {
+			reg = <0x41000000 0x200000>;
+			no-map;
+		};
+
+		wifi_dump@44000000 {
+			reg = <0x44000000 0x600000>;
+			no-map;
+		};
+	};
+
+	cpus {
+		idle-states {
+			CPU_SPC: spc {
+				status = "disabled";
+			};
+		};
+	};
+
+	aliases {
+		serial1 = &gsbi1_serial;
+		mdio-gpio0 = &mdio0;
+		ethernet0 = &gmac3;
+		ethernet1 = &gmac2;
+
+		led-boot = &led_power_green;
+		led-failsafe = &led_power_red;
+		led-running = &led_power_green;
+		led-upgrade = &led_power_green;
+	};
+
+	chosen {
+		bootargs-append = " console=ttyMSM0,115200n8 root=/dev/ubiblock0_1";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		led_power_green: power_green {
+			label = "green:power";
+			gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g_green {
+			label = "green:wlan2g";
+			gpios = <&qcom_pinmux 23 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan2g_yellow {
+			label = "yellow:wlan2g";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan5g_green {
+			label = "green:wlan5g";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
+		};
+
+		led_power_red: power_red {
+			label = "red:power";
+			gpios = <&qcom_pinmux 28 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan5g_yellow {
+			label = "yellow:wlan5g";
+			gpios = <&qcom_pinmux 59 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+
+&qcom_pinmux {
+	spi_pins: spi_pins {
+		mux {
+			pins = "gpio18", "gpio19";
+			function = "gsbi5";
+			drive-strength = <10>;
+			bias-pull-down;
+		};
+
+		clk {
+			pins = "gpio21";
+			function = "gsbi5";
+			drive-strength = <12>;
+			bias-pull-down;
+		};
+
+		cs {
+			pins = "gpio20";
+			function = "gpio";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		mux {
+			pins = "gpio16", "gpio23", "gpio24", "gpio26",
+				   "gpio28", "gpio59";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	button_pins: button_pins {
+		mux {
+			pins = "gpio25";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	uart1_pins: uart1_pins {
+		mux {
+			pins = "gpio51", "gpio52", "gpio53", "gpio54";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-none;
+		};
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_UART_W_FC>;
+	status = "okay";
+
+	serial@12450000 {
+		status = "okay";
+
+		pinctrl-0 = <&uart1_pins>;
+		pinctrl-names = "default";
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	status = "okay";
+
+	spi4: spi@1a280000 {
+		status = "okay";
+		spi-max-frequency = <50000000>;
+
+		pinctrl-0 = <&spi_pins>;
+		pinctrl-names = "default";
+
+		cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+		m25p80@0 {
+			compatible = "jedec,spi-nor";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			spi-max-frequency = <50000000>;
+			reg = <0>;
+
+			partitions {
+				compatible = "qcom,smem";
+			};
+		};
+	};
+};
+
+&hs_phy_0 {		/* USB3 port 0 HS phy */
+	status = "okay";
+};
+
+&hs_phy_1 {		/* USB3 port 1 HS phy */
+	status = "okay";
+};
+
+&ss_phy_0 {		/* USB3 port 0 SS phy */
+	status = "okay";
+};
+
+&ss_phy_1 {		/* USB3 port 1 SS phy */
+	status = "okay";
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+	/delete-property/ perst-gpios;
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi@1,0 {
+			compatible = "qcom,ath10k";
+			status = "okay";
+			reg = <0x00010000 0 0 0 0>;
+			qcom,ath10k-calibration-variant = "Edgecore-ECW5410-L";
+		};
+	};
+};
+
+&pcie2 {
+	status = "okay";
+
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+	/delete-property/ perst-gpios;
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi@1,0 {
+			compatible = "qcom,ath10k";
+			status = "okay";
+			reg = <0x00010000 0 0 0 0>;
+			qcom,ath10k-calibration-variant = "Edgecore-ECW5410-L";
+		};
+	};
+};
+
+&soc {
+	nand@1ac00000 {
+		status = "okay";
+
+		pinctrl-0 = <&nand_pins>;
+		pinctrl-names = "default";
+
+		nand@0 {
+			compatible = "qcom,nandcs";
+
+			reg = <0>;
+
+			nand-ecc-strength = <4>;
+			nand-bus-width = <8>;
+			nand-ecc-step-size = <512>;
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				rootfs1@0 {
+					label = "rootfs1";
+					reg = <0x0000000 0x4000000>;
+				};
+
+				rootfs2@4000000 {
+					label = "rootfs2";
+					reg = <0x4000000 0x4000000>;
+				};
+			};
+		};
+	};
+
+	mdio1: mdio {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		status = "okay";
+
+		pinctrl-0 = <&mdio0_pins>;
+		pinctrl-names = "default";
+
+		gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+
+		phy1: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};
+
+&gmac2 {
+	status = "okay";
+
+	qcom,id = <2>;
+	mdiobus = <&mdio0>;
+
+	phy-mode = "sgmii";
+	phy-handle = <&phy1>;
+};
+
+&gmac3 {
+	status = "okay";
+
+	qcom,id = <3>;
+	mdiobus = <&mdio1>;
+
+	phy-mode = "sgmii";
+	phy-handle = <&phy0>;
+};
+
+&adm_dma {
+	status = "okay";
+};