ipq806x: add v4.9 support

Signed-off-by: John Crispin <john@phrozen.org>

10 files changed, 3628 insertions, 0 deletions

diff --git a/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-c2600.dts b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
new file mode 100644
index 0000000000..7eeaab1557
--- /dev/null
+++ b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
@@ -0,0 +1,501 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "TP-Link Archer C2600";
+	compatible = "tplink,c2600", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power;
+		led-failsafe = &general;
+		led-running = &power;
+		led-upgrade = &general;
+	};
+
+	chosen {
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			button_pins: button_pins {
+				mux {
+					pins = "gpio16", "gpio54", "gpio65";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			led_pins: led_pins {
+				mux {
+					pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33",
+					       "gpio53", "gpio66";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			spi_pins: spi_pins {
+				mux {
+					pins = "gpio18", "gpio19", "gpio21";
+					function = "gsbi5";
+					bias-pull-down;
+				};
+
+				data {
+					pins = "gpio18", "gpio19";
+					drive-strength = <10>;
+				};
+
+				cs {
+					pins = "gpio20";
+					function = "gpio";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				clk {
+					pins = "gpio21";
+					drive-strength = <12>;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			usb0_pwr_en_pin: usb0_pwr_en_pin {
+				mux {
+					pins = "gpio25";
+					function = "gpio";
+					drive-strength = <10>;
+					bias-pull-up;
+					output-high;
+				};
+			};
+
+			usb1_pwr_en_pin: usb1_pwr_en_pin {
+				mux {
+					pins = "gpio23";
+					function = "gpio";
+					drive-strength = <10>;
+					bias-pull-up;
+					output-high;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "ok";
+
+			spi5: spi@1a280000 {
+				status = "ok";
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+				flash: m25p80@0 {
+					compatible = "jedec,spi-nor";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					SBL1@0 {
+						label = "SBL1";
+						reg = <0x0 0x20000>;
+						read-only;
+					};
+
+					MIBIB@20000 {
+						label = "MIBIB";
+						reg = <0x20000 0x20000>;
+						read-only;
+					};
+
+					SBL2@40000 {
+						label = "SBL2";
+						reg = <0x40000 0x20000>;
+						read-only;
+					};
+
+					SBL3@60000 {
+						label = "SBL3";
+						reg = <0x60000 0x30000>;
+						read-only;
+					};
+
+					DDRCONFIG@90000 {
+						label = "DDRCONFIG";
+						reg = <0x90000 0x10000>;
+						read-only;
+					};
+
+					SSD@a0000 {
+						label = "SSD";
+						reg = <0xa0000 0x10000>;
+						read-only;
+					};
+
+					TZ@b0000 {
+						label = "TZ";
+						reg = <0xb0000 0x30000>;
+						read-only;
+					};
+
+					RPM@e0000 {
+						label = "RPM";
+						reg = <0xe0000 0x20000>;
+						read-only;
+					};
+
+					fs-uboot@100000 {
+						label = "fs-uboot";
+						reg = <0x100000 0x70000>;
+						read-only;
+					};
+
+					uboot-env@170000 {
+						label = "uboot-env";
+						reg = <0x170000 0x40000>;
+						read-only;
+					};
+
+					radio@1b0000 {
+						label = "radio";
+						reg = <0x1b0000 0x40000>;
+						read-only;
+					};
+
+					os-image@1f0000 {
+						label = "os-image";
+						reg = <0x1f0000 0x200000>;
+					};
+
+					rootfs@3f0000 {
+						label = "rootfs";
+						reg = <0x3f0000 0x1b00000>;
+					};
+
+					defaultmac: default-mac@1ef0000 {
+						label = "default-mac";
+						reg = <0x1ef0000 0x00200>;
+						read-only;
+					};
+
+					pin@1ef0200 {
+						label = "pin";
+						reg = <0x1ef0200 0x00200>;
+						read-only;
+					};
+
+					product-info@1ef0400 {
+						label = "product-info";
+						reg = <0x1ef0400 0x0fc00>;
+						read-only;
+					};
+
+					partition-table@1f00000 {
+						label = "partition-table";
+						reg = <0x1f00000 0x10000>;
+						read-only;
+					};
+
+					soft-version@1f10000 {
+						label = "soft-version";
+						reg = <0x1f10000 0x10000>;
+						read-only;
+					};
+
+					support-list@1f20000 {
+						label = "support-list";
+						reg = <0x1f20000 0x10000>;
+						read-only;
+					};
+
+					profile@1f30000 {
+						label = "profile";
+						reg = <0x1f30000 0x10000>;
+						read-only;
+					};
+
+					default-config@1f40000 {
+						label = "default-config";
+						reg = <0x1f40000 0x10000>;
+						read-only;
+					};
+
+					user-config@1f50000 {
+						label = "user-config";
+						reg = <0x1f50000 0x40000>;
+						read-only;
+					};
+
+					qos-db@1f90000 {
+						label = "qos-db";
+						reg = <0x1f90000 0x40000>;
+						read-only;
+					};
+
+					usb-config@1fd0000 {
+						label = "usb-config";
+						reg = <0x1fd0000 0x10000>;
+						read-only;
+					};
+
+					log@1fe0000 {
+						label = "log";
+						reg = <0x1fe0000 0x20000>;
+						read-only;
+					};
+				};
+			};
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+
+			pinctrl-0 = <&usb0_pwr_en_pin>;
+			pinctrl-names = "default";
+		};
+
+		usb30@1 {
+			status = "ok";
+
+			pinctrl-0 = <&usb1_pwr_en_pin>;
+			pinctrl-names = "default";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0x6a545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+
+			mtd-mac-address = <&defaultmac 0x8>;
+			mtd-mac-address-increment = <1>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+
+			mtd-mac-address = <&defaultmac 0x8>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		rpm@108000 {
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 49 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		ledswitch {
+			label = "ledswitch";
+			gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LIGHTS_TOGGLE>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		lan {
+			label = "c2600:white:lan";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb4 {
+			label = "c2600:white:usb_4";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb2 {
+			label = "c2600:white:usb_2";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		wps {
+			label = "c2600:white:wps";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_amber {
+			label = "c2600:amber:wan";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
+		};
+
+		wan_white {
+			label = "c2600:white:wan";
+			gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>;
+		};
+
+		power: power {
+			label = "c2600:white:power";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		general: general {
+			label = "c2600:white:general";
+			gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-d7800.dts b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-d7800.dts
new file mode 100644
index 0000000000..a8a613945f
--- /dev/null
+++ b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-d7800.dts
@@ -0,0 +1,406 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear Nighthawk X4 D7800";
+	compatible = "netgear,d7800", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0xe000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power_white;
+		led-failsafe = &power_amber;
+		led-running = &power_white;
+		led-upgrade = &power_amber;
+	};
+
+	chosen {
+		bootargs = "rootfstype=squashfs noinitrd";
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			button_pins: button_pins {
+				mux {
+					pins = "gpio6", "gpio54", "gpio65";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			led_pins: led_pins {
+				mux {
+					pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+						"gpio24","gpio26", "gpio53", "gpio64";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+				pullups {
+					pins = "gpio39";
+					bias-pull-up;
+				};
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					bias-bus-hold;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			usb0_pwr_en_pins: usb0_pwr_en_pins {
+				mux {
+					pins = "gpio15";
+					function = "gpio";
+					drive-strength = <12>;
+					bias-pull-down;
+					output-high;
+				};
+			};
+
+			usb1_pwr_en_pins: usb1_pwr_en_pins {
+				mux {
+					pins = "gpio16", "gpio68";
+					function = "gpio";
+					drive-strength = <12>;
+					bias-pull-down;
+					output-high;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		sata-phy@1b400000 {
+			status = "ok";
+		};
+
+		sata@29000000 {
+			status = "ok";
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+
+			pinctrl-0 = <&usb0_pwr_en_pins>;
+			pinctrl-names = "default";
+		};
+
+		usb30@1 {
+			status = "ok";
+
+			pinctrl-0 = <&usb1_pwr_en_pins>;
+			pinctrl-names = "default";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&pcie0_pins>;
+			pinctrl-names = "default";
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&pcie1_pins>;
+			pinctrl-names = "default";
+		};
+
+		nand@1ac00000 {
+			status = "ok";
+
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
+
+			nand-ecc-strength = <4>;
+			nand-bus-width = <8>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qcadata@0 {
+				label = "qcadata";
+				reg = <0x0000000 0x0c80000>;
+				read-only;
+			};
+
+			APPSBL@c80000 {
+				label = "APPSBL";
+				reg = <0x0c80000 0x0500000>;
+				read-only;
+			};
+
+			APPSBLENV@1180000 {
+				label = "APPSBLENV";
+				reg = <0x1180000 0x0080000>;
+				read-only;
+			};
+
+			art: art@1200000 {
+				label = "art";
+				reg = <0x1200000 0x0140000>;
+				read-only;
+			};
+
+			artbak: art@1340000 {
+				label = "artbak";
+				reg = <0x1340000 0x0140000>;
+				read-only;
+			};
+
+			kernel@1480000 {
+				label = "kernel";
+				reg = <0x1480000 0x0200000>;
+			};
+
+			ubi@1680000 {
+				label = "ubi";
+				reg = <0x1680000 0x1E00000>;
+			};
+
+			netgear@3480000 {
+				label = "netgear";
+				reg = <0x3480000 0x4480000>;
+				read-only;
+			};
+
+			reserve@7900000 {
+				label = "reserve";
+				reg = <0x7900000 0x0700000>;
+				read-only;
+			};
+
+			firmware@1480000 {
+				label = "firmware";
+				reg = <0x1480000 0x2000000>;
+			};
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0x6a545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			phy-handle = <&phy4>;
+			qcom,id = <1>;
+
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+
+			mtd-mac-address = <&art 6>;
+		};
+
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+
+			mtd-mac-address = <&art 0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		rpm@108000 {
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		usb1 {
+			label = "d7800:white:usb1";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb2 {
+			label = "d7800:white:usb2";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_amber: power_amber {
+			label = "d7800:amber:power";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_white {
+			label = "d7800:white:wan";
+			gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_amber {
+			label = "d7800:amber:wan";
+			gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		wps {
+			label = "d7800:white:wps";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+		};
+
+		esata {
+			label = "d7800:white:esata";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_white: power_white {
+			label = "d7800:white:power";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		wifi {
+			label = "d7800:white:wifi";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts
new file mode 100644
index 0000000000..b5840e8717
--- /dev/null
+++ b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts
@@ -0,0 +1,399 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Linksys EA8500 WiFi Router";
+	compatible = "linksys,ea8500", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power;
+		led-failsafe = &power;
+		led-running = &power;
+		led-upgrade = &power;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200n8"; 
+		linux,stdout-path = "serial0:115200n8";
+		append-rootblock = "ubi.mtd=";  /* append to bootargs adding the root deviceblock nbr from bootloader */
+	};
+
+	soc {
+		pinmux@800000 {
+			button_pins: button_pins {
+				mux {
+					pins = "gpio65", "gpio67", "gpio68";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			led_pins: led_pins {
+				mux {
+					pins = "gpio6", "gpio53", "gpio54";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+				pullups {
+					pins = "gpio39";
+					bias-pull-up;
+				};
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					bias-bus-hold;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		sata-phy@1b400000 {
+			status = "ok";
+		};
+
+		sata@29000000 {
+			status = "ok";
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+		};
+
+		usb30@1 {
+			status = "ok";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+		
+		pcie2: pci@1b900000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+		
+		nand@1ac00000 {
+			status = "ok";
+
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
+
+			nand-ecc-strength = <4>;
+			nand-bus-width = <8>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			SBL1@0 {
+				label = "SBL1";
+				reg = <0x0000000 0x0040000>;
+				read-only;
+			};
+
+			MIBIB@40000 {
+				label = "MIBIB";
+				reg = <0x0040000 0x0140000>;
+				read-only;
+			};
+
+			SBL2@180000 {
+				label = "SBL2";
+				reg = <0x0180000 0x0140000>;
+				read-only;
+			};
+
+			SBL3@2c0000 {
+				label = "SBL3";
+				reg = <0x02c0000 0x0280000>;
+				read-only;
+			};
+
+			DDRCONFIG@540000 {
+				label = "DDRCONFIG";
+				reg = <0x0540000 0x0120000>;
+				read-only;
+			};
+
+			SSD@660000 {
+				label = "SSD";
+				reg = <0x0660000 0x0120000>;
+				read-only;
+			};
+
+			TZ@780000 {
+				label = "TZ";
+				reg = <0x0780000 0x0280000>;
+				read-only;
+			};
+
+			RPM@a00000 {
+				label = "RPM";
+				reg = <0x0a00000 0x0280000>;
+				read-only;
+			};
+
+			art: art@c80000 {
+				label = "art";
+				reg = <0x0c80000 0x0140000>;
+				read-only;
+			};
+
+			APPSBL@dc0000 {
+				label = "APPSBL";
+				reg = <0x0dc0000 0x0100000>;
+				read-only;
+			};
+
+			u_env@ec0000 {
+				label = "u_env";
+				reg = <0x0ec0000 0x0040000>;
+			};
+
+			s_env@f00000 {
+				label = "s_env";
+				reg = <0x0f00000 0x0040000>;
+			};
+
+			devinfo@f40000 {
+				label = "devinfo";
+				reg = <0x0f40000 0x0040000>;
+			};
+
+			linux@f80000 { 
+				label = "kernel1";
+				reg = <0x0f80000 0x2800000>;  /* 3 MB spill to rootfs*/
+			};
+
+			rootfs@1280000 {
+				label = "rootfs1";
+				reg = <0x1280000 0x2500000>;
+			};
+
+			linux2@3780000 {
+				label = "kernel2";
+				reg = <0x3780000 0x2800000>;
+			};
+
+			rootfs2@3a80000 {
+				label = "rootfs2";
+				reg = <0x3a80000 0x2500000>;
+			};
+
+			syscfg@5f80000 {
+				label = "syscfg";
+				reg = <0x5f80000 0x2080000>;
+			};
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0x6a545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+			qcom,phy_mdio_addr = <4>;
+			qcom,poll_required = <1>;
+			qcom,rgmii_delay = <0>;
+			qcom,emulation = <0>;
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+		//lan
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+			qcom,phy_mdio_addr = <0>;	/* none */
+			qcom,poll_required = <0>;	/* no polling */
+			qcom,rgmii_delay = <0>;
+			qcom,emulation = <0>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		rpm@108000 {
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
+		};
+
+		adm_dma: dma@18300000 {
+			status = "ok";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART >;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		wps {
+			label = "ea8500:green:wps";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+		};
+
+		power: power {
+			label = "ea8500:white:power";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+
+		wifi {
+			label = "ea8500:green:wifi";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
diff --git a/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-r7500.dts b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-r7500.dts
new file mode 100644
index 0000000000..fc35df7e68
--- /dev/null
+++ b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-r7500.dts
@@ -0,0 +1,373 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear Nighthawk X4 R7500";
+	compatible = "netgear,r7500", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0xe000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power_white;
+		led-failsafe = &power_amber;
+		led-running = &power_white;
+		led-upgrade = &power_amber;
+	};
+
+	chosen {
+		bootargs = "rootfstype=squashfs noinitrd";
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			button_pins: button_pins {
+				mux {
+					pins = "gpio6", "gpio54", "gpio65";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			led_pins: led_pins {
+				mux {
+					pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+						"gpio24","gpio26", "gpio53", "gpio64";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+				pullups {
+					pins = "gpio39";
+					bias-pull-up;
+				};
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					bias-bus-hold;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		sata-phy@1b400000 {
+			status = "ok";
+		};
+
+		sata@29000000 {
+			status = "ok";
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+		};
+
+		usb30@1 {
+			status = "ok";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+		};
+
+		nand@1ac00000 {
+			status = "ok";
+
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
+
+			nand-ecc-strength = <4>;
+			nand-bus-width = <8>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qcadata@0 {
+				label = "qcadata";
+				reg = <0x0000000 0x0c80000>;
+				read-only;
+			};
+
+			APPSBL@c80000 {
+				label = "APPSBL";
+				reg = <0x0c80000 0x0500000>;
+				read-only;
+			};
+
+			APPSBLENV@1180000 {
+				label = "APPSBLENV";
+				reg = <0x1180000 0x0080000>;
+				read-only;
+			};
+
+			art: art@1200000 {
+				label = "art";
+				reg = <0x1200000 0x0140000>;
+				read-only;
+			};
+
+			kernel@1340000 {
+				label = "kernel";
+				reg = <0x1340000 0x0200000>;
+			};
+
+			ubi@1540000 {
+				label = "ubi";
+				reg = <0x1540000 0x1800000>;
+			};
+
+			netgear@2d40000 {
+				label = "netgear";
+				reg = <0x2d40000 0x0c00000>;
+				read-only;
+			};
+
+			reserve@3940000 {
+				label = "reserve";
+				reg = <0x3940000 0x46c0000>;
+				read-only;
+			};
+
+			firmware@1340000 {
+				label = "firmware";
+				reg = <0x1340000 0x1a00000>;
+			};
+
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0x6a545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+
+			mtd-mac-address = <&art 6>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+
+			mtd-mac-address = <&art 0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		rpm@108000 {
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		usb1 {
+			label = "r7500:white:usb1";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb2 {
+			label = "r7500:white:usb2";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_amber: power_amber {
+			label = "r7500:amber:power";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_white {
+			label = "r7500:white:wan";
+			gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_amber {
+			label = "r7500:amber:wan";
+			gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		wps {
+			label = "r7500:white:wps";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+		};
+
+		esata {
+			label = "r7500:white:esata";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_white: power_white {
+			label = "r7500:white:power";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		wifi {
+			label = "r7500:white:wifi";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts
new file mode 100644
index 0000000000..4edfbeb72d
--- /dev/null
+++ b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts
@@ -0,0 +1,416 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear Nighthawk X4 R7500v2";
+	compatible = "netgear,r7500v2", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+
+		rsvd@5fe00000 {
+			reg = <0x5fe00000 0x200000>;
+			reusable;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power;
+		led-failsafe = &power;
+		led-running = &power;
+		led-upgrade = &power;
+	};
+
+	chosen {
+		bootargs = "rootfstype=squashfs noinitrd";
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			button_pins: button_pins {
+				mux {
+					pins = "gpio6", "gpio54", "gpio65";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			led_pins: led_pins {
+				mux {
+					pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+						"gpio24","gpio26", "gpio53", "gpio64";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+				pullups {
+					pins = "gpio39";
+					bias-pull-up;
+				};
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					bias-bus-hold;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			usb0_pwr_en_pins: usb0_pwr_en_pins {
+				mux {
+					pins = "gpio15";
+					function = "gpio";
+					drive-strength = <12>;
+					bias-pull-down;
+					output-high;
+				};
+			};
+
+			usb1_pwr_en_pins: usb1_pwr_en_pins {
+				mux {
+					pins = "gpio16", "gpio68";
+					function = "gpio";
+					drive-strength = <12>;
+					bias-pull-down;
+					output-high;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		sata-phy@1b400000 {
+			status = "ok";
+		};
+
+		sata@29000000 {
+			status = "ok";
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+
+			pinctrl-0 = <&usb0_pwr_en_pins>;
+			pinctrl-names = "default";
+		};
+
+		usb30@1 {
+			status = "ok";
+
+			pinctrl-0 = <&usb1_pwr_en_pins>;
+			pinctrl-names = "default";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+			pinctrl-0 = <&pcie0_pins>;
+			pinctrl-names = "default";
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+			pinctrl-0 = <&pcie1_pins>;
+			pinctrl-names = "default";
+		};
+
+		nand@1ac00000 {
+			status = "ok";
+
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
+
+			nand-ecc-strength = <4>;
+			nand-bus-width = <8>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qcadata@0 {
+				label = "qcadata";
+				reg = <0x0000000 0x0c80000>;
+				read-only;
+			};
+
+			APPSBL@c80000 {
+				label = "APPSBL";
+				reg = <0x0c80000 0x0500000>;
+				read-only;
+			};
+
+			APPSBLENV@1180000 {
+				label = "APPSBLENV";
+				reg = <0x1180000 0x0080000>;
+				read-only;
+			};
+
+			art: art@1200000 {
+				label = "art";
+				reg = <0x1200000 0x0140000>;
+				read-only;
+			};
+
+			artbak: art@1340000 {
+				label = "artbak";
+				reg = <0x1340000 0x0140000>;
+				read-only;
+			};
+
+			kernel@1480000 {
+				label = "kernel";
+				reg = <0x1480000 0x0200000>;
+			};
+
+			ubi@1680000 {
+				label = "ubi";
+				reg = <0x1680000 0x1E00000>;
+			};
+
+			netgear@3480000 {
+				label = "netgear";
+				reg = <0x3480000 0x4480000>;
+				read-only;
+			};
+
+			reserve@7900000 {
+				label = "reserve";
+				reg = <0x7900000 0x0700000>;
+				read-only;
+			};
+
+			firmware@1480000 {
+				label = "firmware";
+				reg = <0x1480000 0x2000000>;
+			};
+
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0xaa545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+
+			mtd-mac-address = <&art 6>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+
+			mtd-mac-address = <&art 0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		rpm@108000 {
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		usb1 {
+			label = "r7500v2:amber:usb1";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb3 {
+			label = "r7500v2:amber:usb3";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		status {
+			label = "r7500v2:amber:status";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		internet {
+			label = "r7500v2:white:internet";
+			gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan {
+			label = "r7500v2:white:wan";
+			gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		wps {
+			label = "r7500v2:white:wps";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+		};
+
+		esata {
+			label = "r7500v2:white:esata";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		power: power {
+			label = "r7500v2:white:power";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		wifi {
+			label = "r7500v2:white:wifi";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts
new file mode 100644
index 0000000000..407c180ec5
--- /dev/null
+++ b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts
@@ -0,0 +1,425 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "TP-Link Archer VR2600v";
+	compatible = "tplink,vr2600v", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power;
+		led-failsafe = &general;
+		led-running = &power;
+		led-upgrade = &general;
+	};
+
+	chosen {
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			led_pins: led_pins {
+				mux {
+					pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17",
+						"gpio26", "gpio53", "gpio56", "gpio66";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			button_pins: button_pins {
+				mux {
+					pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			spi_pins: spi_pins {
+				mux {
+					pins = "gpio18", "gpio19", "gpio21";
+					function = "gsbi5";
+					bias-pull-down;
+				};
+
+				data {
+					pins = "gpio18", "gpio19";
+					drive-strength = <10>;
+				};
+
+				cs {
+					pins = "gpio20";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				clk {
+					pins = "gpio21";
+					drive-strength = <12>;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "ok";
+
+			spi4: spi@1a280000 {
+				status = "ok";
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+				flash: W25Q128@0 {
+					compatible = "jedec,spi-nor";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					SBL1@0 {
+						label = "SBL1";
+						reg = <0x0 0x20000>;
+						read-only;
+					};
+
+					MIBIB@20000 {
+						label = "MIBIB";
+						reg = <0x20000 0x20000>;
+						read-only;
+					};
+
+					SBL2@40000 {
+						label = "SBL2";
+						reg = <0x40000 0x40000>;
+						read-only;
+					};
+
+					SBL3@80000 {
+						label = "SBL3";
+						reg = <0x80000 0x80000>;
+						read-only;
+					};
+
+					DDRCONFIG@100000 {
+						label = "DDRCONFIG";
+						reg = <0x100000 0x10000>;
+						read-only;
+					};
+
+					SSD@110000 {
+						label = "SSD";
+						reg = <0x110000 0x10000>;
+						read-only;
+					};
+
+					TZ@120000 {
+						label = "TZ";
+						reg = <0x120000 0x80000>;
+						read-only;
+					};
+
+					RPM@1a0000 {
+						label = "RPM";
+						reg = <0x1a0000 0x80000>;
+						read-only;
+					};
+
+					APPSBL@220000 {
+						label = "APPSBL";
+						reg = <0x220000 0x80000>;
+						read-only;
+					};
+
+					APPSBLENV@2a0000 {
+						label = "APPSBLENV";
+						reg = <0x2a0000 0x40000>;
+						read-only;
+					};
+
+					OLDART@2e0000 {
+						label = "OLDART";
+						reg = <0x2e0000 0x40000>;
+						read-only;
+					};
+
+					kernel@320000 {
+						label = "kernel";
+						reg = <0x320000 0x200000>;
+					};
+
+					rootfs@520000 {
+						label = "rootfs";
+						reg = <0x520000 0xa60000>;
+					};
+
+					defaultmac: default-mac@0xfaf100 {
+						label = "default-mac";
+						reg = <0xfaf100 0x00200>;
+						read-only;
+					};
+
+					ART@fc0000 {
+						label = "ART";
+						reg = <0xfc0000 0x40000>;
+						read-only;
+					};
+				};
+			};
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+		};
+
+		usb30@1 {
+			status = "ok";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0x6a545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+
+			mtd-mac-address = <&defaultmac 0>;
+			mtd-mac-address-increment = <1>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+
+			mtd-mac-address = <&defaultmac 0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		rpm@108000 {
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		dect {
+			label = "dect";
+			gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PHONE>;
+		};
+
+		ledswitch {
+			label = "ledswitch";
+			gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LIGHTS_TOGGLE>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		dsl {
+			label = "vr2600v:white:dsl";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb {
+			label = "vr2600v:white:usb";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		lan {
+			label = "vr2600v:white:lan";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g {
+			label = "vr2600v:white:wlan2g";
+			gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g {
+			label = "vr2600v:white:wlan5g";
+			gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
+		};
+
+		power: power {
+			label = "vr2600v:white:power";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		phone {
+			label = "vr2600v:white:phone";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan {
+			label = "vr2600v:white:wan";
+			gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
+		};
+
+		general: general {
+			label = "vr2600v:white:general";
+			gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
new file mode 100644
index 0000000000..4db1a30592
--- /dev/null
+++ b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
@@ -0,0 +1,388 @@
+#include "qcom-ipq8065-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "ZyXEL NBG6817";
+	compatible = "zyxel,nbg6817", "qcom,ipq8065";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+		sdcc1 = &sdcc1;
+
+		led-boot = &power;
+		led-failsafe = &power;
+		led-running = &power;
+		led-upgrade = &power;
+	};
+
+	chosen {
+		bootargs = "root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd";
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			button_pins: button_pins {
+				mux {
+					pins = "gpio6", "gpio54", "gpio65";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			led_pins: led_pins {
+				mux {
+					pins = "gpio9", "gpio26", "gpio33", "gpio64";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				clk {
+					pins = "gpio1";
+					input-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				tx {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
+					input-disable;
+				};
+			};
+
+			spi_pins: spi_pins {
+				mux {
+					pins = "gpio18", "gpio19", "gpio21";
+					function = "gsbi5";
+					drive-strength = <10>;
+					bias-none;
+				};
+
+				cs {
+					pins = "gpio20";
+					drive-strength = <12>;
+				};
+			};
+
+			usb0_pwr_en_pins: usb0_pwr_en_pins {
+				mux {
+					pins = "gpio16", "gpio17";
+					function = "gpio";
+					drive-strength = <12>;
+				};
+
+				pwr {
+					pins = "gpio17";
+					bias-pull-down;
+					output-high;
+				};
+
+				ovc {
+					pins = "gpio16";
+					bias-pull-up;
+				};
+			};
+
+			usb1_pwr_en_pins: usb1_pwr_en_pins {
+				mux {
+					pins = "gpio14", "gpio15";
+					function = "gpio";
+					drive-strength = <12>;
+				};
+
+				pwr {
+					pins = "gpio14";
+					bias-pull-down;
+					output-high;
+				};
+
+				ovc {
+					pins = "gpio15";
+					bias-pull-up;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "ok";
+
+			spi4: spi@1a280000 {
+				status = "ok";
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+				flash: m25p80@0 {
+					compatible = "jedec,spi-nor";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <51200000>;
+					reg = <0>;
+
+					linux,part-probe = "qcom-smem";
+				};
+			};
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+
+			pinctrl-0 = <&usb0_pwr_en_pins>;
+			pinctrl-names = "default";
+		};
+
+		usb30@1 {
+			status = "ok";
+
+			pinctrl-0 = <&usb1_pwr_en_pins>;
+			pinctrl-names = "default";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+			pinctrl-0 = <&pcie0_pins>;
+			pinctrl-names = "default";
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+			pinctrl-0 = <&pcie1_pins>;
+			pinctrl-names = "default";
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0xaa545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					0x00970 0x1e864443  /* QM_PORT0_CTRL0 */
+					0x00974 0x000001c6  /* QM_PORT0_CTRL1 */
+					0x00978 0x19008643  /* QM_PORT1_CTRL0 */
+					0x0097c 0x000001c6  /* QM_PORT1_CTRL1 */
+					0x00980 0x19008643  /* QM_PORT2_CTRL0 */
+					0x00984 0x000001c6  /* QM_PORT2_CTRL1 */
+					0x00988 0x19008643  /* QM_PORT3_CTRL0 */
+					0x0098c 0x000001c6  /* QM_PORT3_CTRL1 */
+					0x00990 0x19008643  /* QM_PORT4_CTRL0 */
+					0x00994 0x000001c6  /* QM_PORT4_CTRL1 */
+					0x00998 0x1e864443  /* QM_PORT5_CTRL0 */
+					0x0099c 0x000001c6  /* QM_PORT5_CTRL1 */
+					0x009a0 0x1e864443  /* QM_PORT6_CTRL0 */
+					0x009a4 0x000001c6  /* QM_PORT6_CTRL1 */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+				qca,ar8327-initvals = <
+					0x000e4 0x6a545     /* MAC_POWER_SEL */
+					0x0000c 0x80        /* PAD6_MODE */
+					>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+			qcom,phy_mdio_addr = <4>;
+			qcom,poll_required = <0>;
+			qcom,rgmii_delay = <1>;
+			qcom,phy_mii_type = <0>;
+			qcom,emulation = <0>;
+			qcom,irq = <255>;
+			mdiobus = <&mdio0>;
+
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+			qcom,phy_mdio_addr = <0>;	/* none */
+			qcom,poll_required = <0>;	/* no polling */
+			qcom,rgmii_delay = <0>;
+			qcom,phy_mii_type = <1>;
+			qcom,emulation = <0>;
+			qcom,irq = <258>;
+			mdiobus = <&mdio0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		rpm@108000 {
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
+		};
+
+		amba {
+			sdcc1: sdcc@12400000 {
+				status = "okay";
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		internet {
+			label = "nbg6817:white:internet";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+
+		power: power {
+			label = "nbg6817:white:power";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		wifi2g {
+			label = "nbg6817:amber:wifi2g";
+			gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
+		};
+
+		/* wifi2g amber from the manual is missing */
+
+		wifi5g {
+			label = "nbg6817:amber:wifi5g";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		/* wifi5g amber from the manual is missing */
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065-r7800.dts b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065-r7800.dts
new file mode 100644
index 0000000000..79c8334a42
--- /dev/null
+++ b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065-r7800.dts
@@ -0,0 +1,566 @@
+#include "qcom-ipq8065-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear Nighthawk X4S R7800";
+	compatible = "netgear,r7800", "qcom,ipq8065", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+
+		rsvd@5fe00000 {
+			reg = <0x5fe00000 0x200000>;
+			reusable;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power_white;
+		led-failsafe = &power_amber;
+		led-running = &power_white;
+		led-upgrade = &power_amber;
+	};
+
+	chosen {
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			button_pins: button_pins {
+				mux {
+					pins = "gpio6", "gpio54", "gpio65";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			led_pins: led_pins {
+				pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+					"gpio24","gpio26", "gpio53", "gpio64";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+				pullups {
+					pins = "gpio39";
+					bias-pull-up;
+				};
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					bias-bus-hold;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				clk {
+					pins = "gpio1";
+					input-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				tx {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
+					input-disable;
+				};
+			};
+
+			spi_pins: spi_pins {
+				mux {
+					pins = "gpio18", "gpio19", "gpio21";
+					function = "gsbi5";
+					bias-pull-down;
+				};
+
+				data {
+					pins = "gpio18", "gpio19";
+					drive-strength = <10>;
+				};
+
+				cs {
+					pins = "gpio20";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				clk {
+					pins = "gpio21";
+					drive-strength = <12>;
+				};
+			};
+
+			spi6_pins: spi6_pins {
+				mux {
+					pins = "gpio55", "gpio56", "gpio58";
+					function = "gsbi6";
+					bias-pull-down;
+				};
+
+				mosi {
+					pins = "gpio55";
+					drive-strength = <12>;
+				};
+
+				miso {
+					pins = "gpio56";
+					drive-strength = <14>;
+				};
+
+				cs {
+					pins = "gpio57";
+					drive-strength = <12>;
+					bias-pull-up;
+				};
+
+				clk {
+					pins = "gpio58";
+					drive-strength = <12>;
+				};
+
+				reset {
+					pins = "gpio33";
+					drive-strength = <10>;
+					bias-pull-down;
+					output-high;
+				};
+			};
+
+			usb0_pwr_en_pins: usb0_pwr_en_pins {
+				mux {
+					pins = "gpio15";
+					function = "gpio";
+					drive-strength = <12>;
+					bias-pull-down;
+					output-high;
+				};
+			};
+
+			usb1_pwr_en_pins: usb1_pwr_en_pins {
+				mux {
+					pins = "gpio16", "gpio68";
+					function = "gpio";
+					drive-strength = <12>;
+					bias-pull-down;
+					output-high;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "ok";
+
+			spi5: spi@1a280000 {
+				status = "ok";
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+				flash: m25p80@0 {
+					compatible = "jedec,spi-nor";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					linux,part-probe = "qcom-smem";
+				};
+			};
+		};
+
+		gsbi6: gsbi@16500000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "ok";
+			spi6: spi@16580000 {
+				status = "ok";
+
+				pinctrl-0 = <&spi6_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>;
+
+				spi-nor@0 {
+					compatible = "jedec,spi-nor";
+					reg = <0>;
+					spi-max-frequency = <6000000>;
+				};
+			};
+		};
+
+		sata-phy@1b400000 {
+			status = "ok";
+		};
+
+		sata@29000000 {
+			ports-implemented = <0x1>;
+			status = "ok";
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+
+			pinctrl-0 = <&usb0_pwr_en_pins>;
+			pinctrl-names = "default";
+		};
+
+		usb30@1 {
+			status = "ok";
+
+			pinctrl-0 = <&usb1_pwr_en_pins>;
+			pinctrl-names = "default";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+
+		nand@1ac00000 {
+			status = "ok";
+
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
+
+			nand-ecc-strength = <4>;
+			nand-ecc-step-size = <512>;
+			nand-bus-width = <8>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qcadata@0 {
+				label = "qcadata";
+				reg = <0x0000000 0x0c80000>;
+				read-only;
+			};
+
+			APPSBL@c80000 {
+				label = "APPSBL";
+				reg = <0x0c80000 0x0500000>;
+				read-only;
+			};
+
+			APPSBLENV@1180000 {
+				label = "APPSBLENV";
+				reg = <0x1180000 0x0080000>;
+				read-only;
+			};
+
+			art: art@1200000 {
+				label = "art";
+				reg = <0x1200000 0x0140000>;
+				read-only;
+			};
+
+			artbak: art@1340000 {
+				label = "artbak";
+				reg = <0x1340000 0x0140000>;
+				read-only;
+			};
+
+			kernel@1480000 {
+				label = "kernel";
+				reg = <0x1480000 0x0200000>;
+			};
+
+			ubi@1680000 {
+				label = "ubi";
+				reg = <0x1680000 0x1E00000>;
+			};
+
+			netgear@3480000 {
+				label = "netgear";
+				reg = <0x3480000 0x4480000>;
+				read-only;
+			};
+
+			reserve@7900000 {
+				label = "reserve";
+				reg = <0x7900000 0x0700000>;
+				read-only;
+			};
+
+			firmware@1480000 {
+				label = "firmware";
+				reg = <0x1480000 0x2000000>;
+			};
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0xaa545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					0x00970 0x1e864443  /* QM_PORT0_CTRL0 */
+					0x00974 0x000001c6  /* QM_PORT0_CTRL1 */
+					0x00978 0x19008643  /* QM_PORT1_CTRL0 */
+					0x0097c 0x000001c6  /* QM_PORT1_CTRL1 */
+					0x00980 0x19008643  /* QM_PORT2_CTRL0 */
+					0x00984 0x000001c6  /* QM_PORT2_CTRL1 */
+					0x00988 0x19008643  /* QM_PORT3_CTRL0 */
+					0x0098c 0x000001c6  /* QM_PORT3_CTRL1 */
+					0x00990 0x19008643  /* QM_PORT4_CTRL0 */
+					0x00994 0x000001c6  /* QM_PORT4_CTRL1 */
+					0x00998 0x1e864443  /* QM_PORT5_CTRL0 */
+					0x0099c 0x000001c6  /* QM_PORT5_CTRL1 */
+					0x009a0 0x1e864443  /* QM_PORT6_CTRL0 */
+					0x009a4 0x000001c6  /* QM_PORT6_CTRL1 */
+					>;
+				qca,ar8327-vlans = <
+					0x1	0x5e	    /* VLAN1 Ports 1/2/3/4/6 */
+					0x2	0x21	    /* VLAN2 Ports 0/5 */
+				>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+				qca,ar8327-initvals = <
+					0x000e4 0x6a545     /* MAC_POWER_SEL */
+					0x0000c 0x80        /* PAD6_MODE */
+					>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+			qcom,phy_mdio_addr = <4>;
+			qcom,poll_required = <0>;
+			qcom,rgmii_delay = <1>;
+			qcom,phy_mii_type = <0>;
+			qcom,emulation = <0>;
+			qcom,irq = <255>;
+			mdiobus = <&mdio0>;
+
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+
+			mtd-mac-address = <&art 6>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+			qcom,phy_mdio_addr = <0>;	/* none */
+			qcom,poll_required = <0>;	/* no polling */
+			qcom,rgmii_delay = <0>;
+			qcom,phy_mii_type = <1>;
+			qcom,emulation = <0>;
+			qcom,irq = <258>;
+			mdiobus = <&mdio0>;
+
+			mtd-mac-address = <&art 0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		rpm@108000 {
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+			debounce-interval = <60>;
+			wakeup-source;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+			debounce-interval = <60>;
+			wakeup-source;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+			debounce-interval = <60>;
+			wakeup-source;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		power_white: power_white {
+			label = "r7800:white:power";
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		power_amber: power_amber {
+			label = "r7800:amber:power";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_white {
+			label = "r7800:white:wan";
+			gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan_amber {
+			label = "r7800:amber:wan";
+			gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb1 {
+			label = "r7800:white:usb1";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb2 {
+			label = "r7800:white:usb2";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		esata {
+			label = "r7800:white:esata";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		wifi {
+			label = "r7800:white:wifi";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+
+		wps {
+			label = "r7800:white:wps";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065-v1.0.dtsi b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065-v1.0.dtsi
new file mode 100644
index 0000000000..22b5338cc0
--- /dev/null
+++ b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065-v1.0.dtsi
@@ -0,0 +1 @@
+#include "qcom-ipq8065.dtsi"
diff --git a/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065.dtsi b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065.dtsi
new file mode 100644
index 0000000000..b3ccb2ede2
--- /dev/null
+++ b/target/linux/ipq806x/files-4.4/arch/arm/boot/dts/qcom-ipq8065.dtsi
@@ -0,0 +1,153 @@
+#include "qcom-ipq8064.dtsi"
+
+/ {
+	model = "Qualcomm IPQ8065";
+	compatible = "qcom,ipq8065", "qcom,ipq8064";
+
+	qcom,pvs {
+		qcom,pvs-format-a;
+		qcom,speed0-pvs0-bin-v0 =
+			< 1725000000 1262500 >,
+			< 1400000000 1175000 >,
+			< 1000000000 1100000 >,
+			 < 800000000 1050000 >,
+			 < 600000000 1000000 >,
+			 < 384000000 975000 >;
+		qcom,speed0-pvs1-bin-v0 =
+			< 1725000000 1225000 >,
+			< 1400000000 1150000 >,
+			< 1000000000 1075000 >,
+			 < 800000000 1025000 >,
+			 < 600000000 975000 >,
+			 < 384000000 950000 >;
+		qcom,speed0-pvs2-bin-v0 =
+			< 1725000000 1200000 >,
+			< 1400000000 1125000 >,
+			< 1000000000 1050000 >,
+			 < 800000000 1000000 >,
+			 < 600000000 950000 >,
+			 < 384000000 925000 >;
+		qcom,speed0-pvs3-bin-v0 =
+			< 1725000000 1175000 >,
+			< 1400000000 1100000 >,
+			< 1000000000 1025000 >,
+			 < 800000000 975000 >,
+			 < 600000000 925000 >,
+			 < 384000000 900000 >;
+		qcom,speed0-pvs4-bin-v0 =
+			< 1725000000 1150000 >,
+			< 1400000000 1075000 >,
+			< 1000000000 1000000 >,
+			 < 800000000 950000 >,
+			 < 600000000 900000 >,
+			 < 384000000 875000 >;
+		qcom,speed0-pvs5-bin-v0 =
+			< 1725000000 1100000 >,
+			< 1400000000 1025000 >,
+			< 1000000000 950000 >,
+			 < 800000000 900000 >,
+			 < 600000000 850000 >,
+			 < 384000000 825000 >;
+		qcom,speed0-pvs6-bin-v0 =
+			< 1725000000 1050000 >,
+			< 1400000000 975000 >,
+			< 1000000000 900000 >,
+			 < 800000000 850000 >,
+			 < 600000000 800000 >,
+			 < 384000000 775000 >;
+	};
+
+	soc: soc {
+
+		rpm@108000 {
+
+			regulators {
+
+				smb208_s2a: s2a {
+					regulator-min-microvolt = <775000>;
+					regulator-max-microvolt = <1275000>;
+				};
+
+				smb208_s2b: s2b {
+					regulator-min-microvolt = <775000>;
+					regulator-max-microvolt = <1275000>;
+				};
+			};
+		};
+
+		/* Temporary fixed regulator */
+		vsdcc_fixed: vsdcc-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "SDCC Power";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		sdcc1bam:dma@12402000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12402000 0x8000>;
+			interrupts = <0 98 0>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+                };
+
+		sdcc3bam:dma@12182000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12182000 0x8000>;
+			interrupts = <0 96 0>;
+			clocks = <&gcc SDC3_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		amba {
+			compatible = "arm,amba-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			sdcc1: sdcc@12400000 {
+				status          = "disabled";
+				compatible      = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				reg             = <0x12400000 0x2000>;
+				interrupts      = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks          = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names     = "mclk", "apb_pclk";
+				bus-width       = <8>;
+				max-frequency   = <96000000>;
+				non-removable;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				vmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+				dma-names = "tx", "rx";
+			};
+
+			sdcc3: sdcc@12180000 {
+				compatible      = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				status          = "disabled";
+				reg             = <0x12180000 0x2000>;
+				interrupts      = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks          = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names     = "mclk", "apb_pclk";
+				bus-width       = <8>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency   = <192000000>;
+				#mmc-ddr-1_8v;
+				sd-uhs-sdr104;
+				sd-uhs-ddr50;
+				vqmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+				dma-names = "tx", "rx";
+			};
+		};
+	};
+};