aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
diff options
context:
space:
mode:
authorPawel Dembicki <paweldembicki@gmail.com>2021-11-23 09:10:14 +0100
committerChristian Lamparter <chunkeey@gmail.com>2022-02-05 00:44:35 +0100
commita91ab8bc05b737d7e14976aaf929a71ea37fa1c6 (patch)
tree2c8bdc6ef3cab606663d7056f4a30837d76e3213 /target/linux/ipq40xx
parent4d3e17e205b7abc12ad40bf6a3d32a06d8f07dc6 (diff)
downloadupstream-a91ab8bc05b737d7e14976aaf929a71ea37fa1c6.tar.gz
upstream-a91ab8bc05b737d7e14976aaf929a71ea37fa1c6.tar.bz2
upstream-a91ab8bc05b737d7e14976aaf929a71ea37fa1c6.zip
ipq40xx: add support for ZTE MF286D
ZTE MF286D is a LTE router with four gigabit ethernet ports and integrated QMI mPCIE modem. Hardware specification: - CPU: IPQ4019 - RAM: 256MB - Flash: NAND 128MB + NOR 2MB - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2 - LTE: mPCIe cat 12 card (Modem chipset MDM9250) - LAN: 4 Gigabit Ports - USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem) - Serial console: X8 connector 115200 8n1 Known issues: - Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs are driven by cpu. - Wifi LED is triggered by phy0tpt only - No VoIP support - LAN1/WAN port is configured as WAN - ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN and WLAN0/1 Opening the case: 1. Take of battery lid (no battery support for this model, battery cage is dummy). 2. Unscrew screw placed behind battery lid. 3. Take off back cover. It attached with multiple plastic clamps. 4. Unscrew four more screws hidden behind back case. 5. Remove front panel from blue chassis. There are more plastic clamps. 6. Unscrew two boards, which secures the PCB in the chassis. 7. Extract board from blue chassis. Console connection (X8 connector): 1. Parameters: 115200 8N1 2. Pin description: (from closest pin to X8 descriptor to farthest) - VCC (3.3V) - TX - RX - GND Install Instructions: Serial + initramfs: 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.1.3 2. Connect serial console (115200,8n1) to X8 connector. 3. Connect TFTP server to RJ-45 port. 4. Stop in u-Boot and run u-Boot commands: setenv serverip 192.168.1.3 setenv ipaddr 192.168.1.72 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock. 6. Login via ssh or serial and remove stock partitions: ubiattach -m 9 ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. Install image via "sysupgrade -n". Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (cosmetic changes to the commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Diffstat (limited to 'target/linux/ipq40xx')
-rw-r--r--target/linux/ipq40xx/base-files/etc/board.d/02_network5
-rw-r--r--target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches3
-rw-r--r--target/linux/ipq40xx/base-files/lib/upgrade/platform.sh26
-rw-r--r--target/linux/ipq40xx/config-5.101
-rw-r--r--target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-mf286d.dts435
-rw-r--r--target/linux/ipq40xx/image/generic.mk13
-rw-r--r--target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch3
7 files changed, 484 insertions, 2 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index c39890ecd9..11ebb2ef83 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -140,6 +140,11 @@ ipq40xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "0u@eth1" "5:wan"
;;
+ zte,mf286d)
+ ucidef_set_interfaces_lan_wan "eth0" "eth1"
+ ucidef_add_switch "switch0" \
+ "0u@eth0" "2:lan:4" "3:lan:3" "4:lan:2" "0u@eth1" "5:wan"
+ ;;
*)
echo "Unsupported hardware. Network interfaces not initialized"
;;
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
index 5d39d37c08..a52a33d2f4 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
+++ b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
@@ -24,6 +24,9 @@ mikrotik,cap-ac)
mikrotik,hap-ac3)
ucidef_add_gpio_switch "poe_passtrough" "PoE Passthrough" "452" "0"
;;
+zte,mf286d)
+ ucidef_add_gpio_switch "power_btn_block" "Power button blocker" "421" "0"
+ ;;
esac
board_config_flush
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index d0e9b5b020..e8c94409a7 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -25,6 +25,29 @@ Once this is done. Retry.
EOF
return 1
;;
+ zte,mf286d)
+ CI_UBIPART="rootfs"
+ local mtdnum="$( find_mtd_index $CI_UBIPART )"
+ [ ! "$mtdnum" ] && return 1
+ ubiattach -m "$mtdnum" || true
+ local ubidev="$( nand_find_ubi $CI_UBIPART )"
+ local ubi_rootfs=$(nand_find_volume $ubidev ubi_rootfs)
+ local ubi_rootfs_data=$(nand_find_volume $ubidev ubi_rootfs_data)
+
+ [ -n "$ubi_rootfs" ] || [ -n "$ubi_rootfs_data" ] || return 0
+
+ cat << EOF
+ubi_rootfs partition is still present.
+
+You need to delete the stock partition first:
+# ubirmvol /dev/ubi0 -N ubi_rootfs
+Please also delete ubi_rootfs_data, if exist:
+# ubirmvol /dev/ubi0 -N ubi_rootfs_data
+
+Once this is done. Retry.
+EOF
+ return 1
+ ;;
esac
return 0;
}
@@ -161,7 +184,8 @@ platform_do_upgrade() {
PART_NAME="inactive"
platform_do_upgrade_dualboot_datachk "$1"
;;
- teltonika,rutx10)
+ teltonika,rutx10 |\
+ zte,mf286d)
CI_UBIPART="rootfs"
nand_do_upgrade "$1"
;;
diff --git a/target/linux/ipq40xx/config-5.10 b/target/linux/ipq40xx/config-5.10
index b944c11d16..3ebc7b3e1e 100644
--- a/target/linux/ipq40xx/config-5.10
+++ b/target/linux/ipq40xx/config-5.10
@@ -365,6 +365,7 @@ CONFIG_PINCTRL_MSM=y
CONFIG_PM_OPP=y
CONFIG_POWER_RESET=y
CONFIG_POWER_RESET_MSM=y
+CONFIG_POWER_RESET_GPIO_RESTART=y
CONFIG_POWER_SUPPLY=y
CONFIG_PPS=y
CONFIG_PRINTK_TIME=y
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-mf286d.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-mf286d.dts
new file mode 100644
index 0000000000..8d1505cfe9
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-mf286d.dts
@@ -0,0 +1,435 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (c) 2022, Pawel Dembicki <paweldembicki@gmail.com>.
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/soc/qcom,tcsr.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "ZTE MF286D";
+ compatible = "zte,mf286d";
+
+ aliases {
+ led-boot = &led_internal;
+ led-failsafe = &led_internal;
+ led-running = &led_internal;
+ led-upgrade = &led_internal;
+ };
+
+ chosen {
+ /*
+ * bootargs forced by u-boot bootipq command:
+ * 'ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait'
+ */
+ bootargs-append = " root=/dev/ubiblock0_1";
+ };
+
+ gpio-restart {
+ compatible = "gpio-restart";
+ gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_internal: led-0 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
+ label = "blue:internal_led";
+ default-state = "keep";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_WLAN;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wifi {
+ label = "wifi";
+ linux,code = <KEY_RFKILL>;
+ gpios = <&tlmm 11 GPIO_ACTIVE_LOW>;
+ };
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <2000>;
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2@60f8800 {
+ status = "okay";
+ };
+
+ usb3@8af8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ /* u-boot is looking for "n25q128a11" property */
+ compatible = "jedec,spi-nor", "n25q128a11";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "0:SBL1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "0:MIBIB";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "0:QSEE";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "0:CDT";
+ reg = <0xc0000 0x10000>;
+ read-only;
+ };
+
+ partition@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0xd0000 0x10000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "0:APPSBLENV";
+ reg = <0xe0000 0x10000>;
+ read-only;
+ };
+
+ partition@f0000 {
+ label = "0:APPSBL";
+ reg = <0xf0000 0xc0000>;
+ read-only;
+ };
+
+ partition@1b0000 {
+ label = "0:reserved1";
+ reg = <0x1b0000 0x50000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_config_0>;
+};
+
+&gmac1 {
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_config_0>;
+ mac-address-increment = <1>;
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "fota-flag";
+ reg = <0x0 0xa0000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "ART";
+ reg = <0xa0000 0x80000>;
+ read-only;
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ precal_art_1000: precal@1000 {
+ reg = <0x1000 0x2f20>;
+ };
+
+ precal_art_5000: precal@5000 {
+ reg = <0x5000 0x2f20>;
+ };
+ };
+
+ partition@120000 {
+ label = "mac";
+ reg = <0x120000 0x80000>;
+ read-only;
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_config_0: macaddr@0 {
+ reg = <0x0 0x6>;
+ };
+ };
+
+ partition@1a0000 {
+ label = "reserved2";
+ reg = <0x1a0000 0xc0000>;
+ read-only;
+ };
+
+ partition@260000 {
+ label = "cfg-param";
+ reg = <0x260000 0x400000>;
+ read-only;
+ };
+
+ partition@660000 {
+ label = "log";
+ reg = <0x660000 0x400000>;
+ };
+
+ partition@a60000 {
+ label = "oops";
+ reg = <0xa60000 0xa0000>;
+ };
+
+ partition@b00000 {
+ label = "reserved3";
+ reg = <0xb00000 0x500000>;
+ read-only;
+ };
+
+ partition@1000000 {
+ label = "web";
+ reg = <0x1000000 0x800000>;
+ };
+
+ partition@1800000 {
+ label = "rootfs";
+ reg = <0x1800000 0x1d00000>;
+ };
+
+ partition@3500000 {
+ label = "data";
+ reg = <0x3500000 0x1900000>;
+ };
+
+ partition@4e00000 {
+ label = "fota";
+ reg = <0x4e00000 0x3200000>;
+ };
+ };
+ };
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ i2c_0_pins: i2c_0_pinmux {
+ mux {
+ pins = "gpio20", "gpio21";
+ function = "blsp_i2c0";
+ bias-disable;
+ };
+ };
+
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio52", "gpio53", "gpio58",
+ "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ nvmem-cell-names = "pre-calibration", "mac-address";
+ nvmem-cells = <&precal_art_1000>, <&macaddr_config_0>;
+ mac-address-increment = <2>;
+ qcom,ath10k-calibration-variant = "zte,mf286d";
+};
+
+&wifi1 {
+ status = "okay";
+ nvmem-cell-names = "pre-calibration", "mac-address";
+ nvmem-cells = <&precal_art_5000>, <&macaddr_config_0>;
+ mac-address-increment = <3>;
+ qcom,ath10k-calibration-variant = "zte,mf286d";
+};
diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk
index b22d261d65..15e9a24544 100644
--- a/target/linux/ipq40xx/image/generic.mk
+++ b/target/linux/ipq40xx/image/generic.mk
@@ -977,6 +977,19 @@ define Device/unielec_u4019-32m
endef
TARGET_DEVICES += unielec_u4019-32m
+define Device/zte_mf286d
+ $(call Device/FitzImage)
+ DEVICE_VENDOR := ZTE
+ DEVICE_MODEL := MF286D
+ SOC := qcom-ipq4019
+ DEVICE_DTS_CONFIG := config@ap.dk04.1-c1
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ KERNEL_IN_UBI := 1
+ DEVICE_PACKAGES := ipq-wifi-zte_mf286d kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
+endef
+TARGET_DEVICES += zte_mf286d
+
define Device/zyxel_nbg6617
$(call Device/FitImageLzma)
DEVICE_VENDOR := ZyXEL
diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
index 09ea4efddd..c8229f28d7 100644
--- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -902,11 +902,73 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -902,11 +902,74 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -60,6 +60,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4019-hap-ac3.dtb \
+ qcom-ipq4019-map-ac2200.dtb \
+ qcom-ipq4019-lhgg-60ad.dtb \
++ qcom-ipq4019-mf286d.dtb \
+ qcom-ipq4019-mr8300.dtb \
+ qcom-ipq4019-pa2200.dtb \
+ qcom-ipq4019-r619ac-64m.dtb \