aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
diff options
context:
space:
mode:
authorSteven Lin <steven.lin@senao.com>2018-10-19 16:55:08 +0800
committerMathias Kresin <dev@kresin.me>2018-12-05 09:40:32 +0100
commit2b4ac79a791d9451f601d494dde2e71864174358 (patch)
treeefdddf6c8757a2f19f4998ef1e1a25e152a81b79 /target/linux/ipq40xx
parente261c8b76407ebd2d8289e3522bd02e5bd6e8552 (diff)
downloadupstream-2b4ac79a791d9451f601d494dde2e71864174358.tar.gz
upstream-2b4ac79a791d9451f601d494dde2e71864174358.tar.bz2
upstream-2b4ac79a791d9451f601d494dde2e71864174358.zip
ipq40xx: add support for EnGenius EAP1300
SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm 2. Load image via GUI a. Upgrade EAP1300 to FW v3.5.3.2 In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade. b. Transfer to OpenWrt from EnGenius. In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin. 3. Revert to EnGenius EAP1300 To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration. $ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin Signed-off-by: Steven Lin <steven.lin@senao.com>
Diffstat (limited to 'target/linux/ipq40xx')
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/01_leds6
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/02_network13
-rw-r--r--target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata2
-rw-r--r--target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-eap1300.dts230
-rw-r--r--target/linux/ipq40xx/image/Makefile14
-rw-r--r--target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch3
6 files changed, 261 insertions, 7 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index ab2f77ee10..5e382c03a7 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -23,6 +23,12 @@ avm,fritzbox-4040)
ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
;;
+engenius,eap1300)
+ ucidef_set_led_netdev "lan" "LAN" "${boardname}:blue:lan" "eth0"
+ ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt"
+ ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:yellow:wlan5g" "phy1tpt"
+ ucidef_set_led_default "mesh" "MESH" "${boardname}:blue:mesh" "0"
+ ;;
glinet,gl-b1300)
ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
;;
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 5c90ef136f..d73914c7c1 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -33,6 +33,13 @@ avm,fritzbox-4040)
compex,wpj428)
ucidef_set_interface_lan "eth0 eth1"
;;
+engenius,eap1300 |\
+meraki,mr33 |\
+netgear,ex6100v2 |\
+netgear,ex6150v2 |\
+zyxel,wre6606)
+ ucidef_set_interface_lan "eth0"
+ ;;
glinet,gl-b1300)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
@@ -42,12 +49,6 @@ openmesh,a42 |\
openmesh,a62)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
-meraki,mr33 |\
-netgear,ex6100v2 |\
-netgear,ex6150v2 |\
-zyxel,wre6606)
- ucidef_set_interface_lan "eth0"
- ;;
zyxel,nbg6617)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 1d4fd9cd8f..605a03be1d 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -142,6 +142,7 @@ case "$FIRMWARE" in
ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 0)
;;
compex,wpj428 |\
+ engenius,eap1300 |\
openmesh,a42 |\
openmesh,a62)
ath10kcal_extract "0:ART" 4096 12064
@@ -178,6 +179,7 @@ case "$FIRMWARE" in
ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 12)
;;
compex,wpj428 |\
+ engenius,eap1300 |\
openmesh,a42 |\
openmesh,a62)
ath10kcal_extract "0:ART" 20480 12064
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-eap1300.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-eap1300.dts
new file mode 100644
index 0000000000..7ef0529832
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-eap1300.dts
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "EnGenius EAP1300";
+ compatible = "engenius,eap1300", "qcom,ipq4019";
+
+ soc {
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ serial@78af000 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ aliases {
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ power: orange {
+ label = "eap1300:orange:power";
+ gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+ };
+
+ lan {
+ label = "eap1300:blue:lan";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ mesh {
+ label = "eap1300:blue:mesh";
+ gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan2g {
+ label = "eap1300:blue:wlan2g";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan5g {
+ label = "eap1300:yellow:wlan5g";
+ gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio54", "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ m25p80@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "0:SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition1@40000 {
+ label = "0:MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition2@60000 {
+ label = "0:QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition3@c0000 {
+ label = "0:CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition4@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition5@e0000 {
+ label = "0:APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+ partition6@f0000 {
+ label = "0:APPSBL";
+ reg = <0x000f0000 0x00090000>;
+ read-only;
+ };
+ partition7@180000 {
+ label = "0:ART";
+ reg = <0x00180000 0x00010000>;
+ read-only;
+ };
+ partition8@190000 {
+ label = "firmware";
+ reg = <0x190000 0x1dc0000>;
+ };
+ partition9@1f50000 {
+ label = "u-boot-env";
+ reg = <0x01f50000 0x00010000>;
+ };
+ partition10@1f60000 {
+ label = "userconfig";
+ reg = <0x01f60000 0x000a0000>;
+ };
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+ vlan_tag = <1 0x10>;
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "EnGenius-EAP1300";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "EnGenius-EAP1300";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 8a42d3e780..eaf9f68395 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -105,6 +105,20 @@ define Device/compex_wpj428
endef
TARGET_DEVICES += compex_wpj428
+define Device/engenius_eap1300
+ $(call Device/FitImage)
+ DEVICE_TITLE := EnGenius EAP1300
+ DEVICE_DTS_CONFIG := config@4
+ BOARD_NAME := eap1300
+ DEVICE_DTS := qcom-ipq4018-eap1300
+ KERNEL_SIZE := 5120k
+ IMAGE_SIZE := 25344k
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+ DEVICE_PACKAGES := ipq-wifi-engenius_eap1300
+endef
+TARGET_DEVICES += engenius_eap1300
+
define Device/glinet_gl-b1300
$(call Device/FitImage)
DEVICE_TITLE := GL.iNet GL-B1300
diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
index 8066f986a4..46c34038d6 100644
--- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
@@ -10,11 +10,12 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -697,7 +697,20 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -697,7 +697,21 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
+ qcom-ipq4018-a42.dtb \
++ qcom-ipq4018-eap1300.dtb \
+ qcom-ipq4018-ex6100v2.dtb \
+ qcom-ipq4018-ex6150v2.dtb \
+ qcom-ipq4018-fritz4040.dtb \