aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/image
diff options
context:
space:
mode:
authorDavid Bauer <mail@david-bauer.net>2020-01-12 00:36:42 +0100
committerDavid Bauer <mail@david-bauer.net>2020-01-14 09:38:32 +0100
commitc6e972c8772a628a1a2f2e5590d7c6f4acef9ab0 (patch)
tree560d37a0bf312eac6d70c36e64cc5e3c2c821f40 /target/linux/ipq40xx/image
parent66eb88edb66d49939bda444ff36ea4bf0aaf9ae1 (diff)
downloadupstream-c6e972c8772a628a1a2f2e5590d7c6f4acef9ab0.tar.gz
upstream-c6e972c8772a628a1a2f2e5590d7c6f4acef9ab0.tar.bz2
upstream-c6e972c8772a628a1a2f2e5590d7c6f4acef9ab0.zip
ipq40xx: add support for Aruba AP-303H
The Aruba AP-303H is the hospitality version of the Aruba AP-303 with a POE-passthrough enabled ethernet switch instead of a sigle PHY. Hardware -------- SoC: Qualcomm IPQ4029 RAM: 512M DDR3 FLASH: - 128MB SPI-NAND (Macronix) - 4MB SPI-NOR (Macronix MX25R3235F) TPM: Atmel AT97SC3203 BLE: Texas Instruments CC2540T attached to ttyMSM1 ETH: Qualcomm QCA8075 LED: WiFi (amber / green) System (red / green /amber) PSE (green) BTN: Reset USB: USB 2.0 To connect to the serial console, you can solder to the labled pads next to the USB port or use your Aruba supplied UARt adapter. Do NOT plug a standard USB cable into the Console labled USB-port! Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself an adapter cable: VCC - NC D+ - TX D- - RX GND - GND The console setting in bootloader and OS is 9600 8N1. Voltage level is 3.3V. To enable a full list of commands in the U-Boot "help" command, execute the literal "diag" command. Installation ------------ 1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it into the TFTP server root directory. Configure the TFTP server to be reachable at 192.168.1.75/24. Connect the machine running the TFTP server to the E0 (!) ethernet port of the access point, as it only tries to pull from the WAN port. 2. Connect to the serial console. Interrupt autobooting by pressing Enter when prompted. 3. Configure the bootargs and bootcmd for OpenWrt. $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM0,9600n8" $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1; ubi read 0x85000000 kernel; set fdt_high 0x87000000; bootm 0x85000000" $ setenv ramboot_openwrt "run bootargs_openwrt; setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75; netget; set fdt_high 0x87000000; bootm" $ setenv bootcmd "run nandboot_openwrt" $ saveenv 4. Load OpenWrt into RAM: $ run ramboot_openwrt 5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the /tmp folder on the device. You will need to plug into E1-E3 ports of the access point to reach OpenWrt, as E0 is the WAN port of the device. 6. Flash OpenWrt: $ ubidetach -p /dev/mtd16 $ ubiformat /dev/mtd16 $ sysupgrade -n /tmp/openwrt-sysupgrade.bin To go back to the stock firmware, simply reset the bootcmd in the bootloader to the original value: $ setenv bootcmd "boot" $ saveenv Signed-off-by: David Bauer <mail@david-bauer.net>
Diffstat (limited to 'target/linux/ipq40xx/image')
-rw-r--r--target/linux/ipq40xx/image/Makefile10
1 files changed, 10 insertions, 0 deletions
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 0a8dca26bc..588a24c2fe 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -102,6 +102,16 @@ define Device/aruba_ap-303
endef
TARGET_DEVICES += aruba_ap-303
+define Device/aruba_ap-303h
+ $(call Device/FitImageLzma)
+ DEVICE_VENDOR := Aruba
+ DEVICE_MODEL := AP-303H
+ SOC := qcom-ipq4029
+ DEVICE_PACKAGES := ipq-wifi-aruba_ap-303
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += aruba_ap-303h
+
define Device/asus_map-ac2200
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS