aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/files-4.14/arch/arm
diff options
context:
space:
mode:
authorSven Eckelmann <sven.eckelmann@openmesh.com>2017-08-09 13:52:07 +0200
committerMathias Kresin <dev@kresin.me>2018-04-23 22:07:22 +0200
commit0b204902075157dbb002ea04f41a5b1a4fbe848c (patch)
treeaab0a3eabea2d909bb41909c6a6d0b5583967495 /target/linux/ipq40xx/files-4.14/arch/arm
parentc6aac196b80039ae1716b9af635c06992e62171f (diff)
downloadupstream-0b204902075157dbb002ea04f41a5b1a4fbe848c.tar.gz
upstream-0b204902075157dbb002ea04f41a5b1a4fbe848c.tar.bz2
upstream-0b204902075157dbb002ea04f41a5b1a4fbe848c.zip
ipq40xx: add support for OpenMesh A62
* QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + 802.3at POE+ - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 18-24V passive POE (mode B) * powered only via POE The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. The initramfs image can be started using setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)' tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb set fdt_high 0x85000000 bootm 0x84000000 Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Diffstat (limited to 'target/linux/ipq40xx/files-4.14/arch/arm')
-rw-r--r--target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-a62.dts240
1 files changed, 240 insertions, 0 deletions
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-a62.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-a62.dts
new file mode 100644
index 0000000000..dd6d6bd775
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-a62.dts
@@ -0,0 +1,240 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2017-2018, Sven Eckelmann <sven.eckelmann@openmesh.com>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include "qcom-ipq4019-bus.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "OpenMesh A62";
+ compatible = "openmesh,a62", "qcom,ipq4019";
+
+ soc {
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+ };
+
+ serial@78af000 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ switch_lan_bmp = <0x10>;
+ switch_wan_bmp = <0x20>;
+
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART >;
+ };
+ };
+
+ aliases {
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ red {
+ label = "a62:red:status";
+ gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-off";
+ };
+
+ power: green {
+ label = "a62:green:status";
+ gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+ };
+
+ blue {
+ label = "a62:blue:status";
+ gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-off";
+ };
+ };
+
+ watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
+ hw_algo = "toggle";
+ /* hw_margin_ms is actually 300s but driver limits it to 60s */
+ hw_margin_ms = <60000>;
+ always-running;
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ enable-usb-power {
+ gpio-hog;
+ gpios = <58 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "enable USB2 power";
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&spi_0 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ /* partitions are passed via bootloader */
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x10>;
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+
+ ath10k@0,0 {
+ compatible = "qcom,ath10k";
+ status = "okay";
+ reg = <0 0 0 0 0>;
+ device_type = "pci";
+ qcom,ath10k-calibration-variant = "OM-A62";
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "OM-A62";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "OM-A62";
+};