aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts
diff options
context:
space:
mode:
authorChris Blake <chrisrblake93@gmail.com>2018-03-10 10:59:18 +0100
committerMathias Kresin <dev@kresin.me>2018-03-14 19:04:52 +0100
commit4943afd7818f56053231a5a7ae90e55da44f1f08 (patch)
tree3f54b0e72647dc6ef0a595e2e377aeb3ae58a9a9 /target/linux/ipq40xx/files-4.14/arch/arm/boot/dts
parent4f4fc993db4cd074fb2b51586dadd10e882604ec (diff)
downloadupstream-4943afd7818f56053231a5a7ae90e55da44f1f08.tar.gz
upstream-4943afd7818f56053231a5a7ae90e55da44f1f08.tar.bz2
upstream-4943afd7818f56053231a5a7ae90e55da44f1f08.zip
ipq40xx: add Cisco Meraki MR33 Support
This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: <https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427> Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: <https://openwrt.org/toh/meraki/mr33> (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Diffstat (limited to 'target/linux/ipq40xx/files-4.14/arch/arm/boot/dts')
-rw-r--r--target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4029-mr33.dts403
1 files changed, 403 insertions, 0 deletions
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4029-mr33.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4029-mr33.dts
new file mode 100644
index 0000000000..9c1ef4f020
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4029-mr33.dts
@@ -0,0 +1,403 @@
+/*
+ * Device Tree Source for Meraki MR33 (Stinkbug)
+ *
+ * Copyright (C) 2017 Chris Blake <chrisrblake93@gmail.com>
+ * Copyright (C) 2017 Christian Lamparter <chunkeey@googlemail.com>
+ *
+ * Based on Cisco Meraki DTS from GPL release r25-linux-3.14-20170427
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include "qcom-ipq4019-bus.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Meraki MR33 Access Point";
+ compatible = "meraki,mr33", "qcom,ipq4019";
+
+ aliases {
+ led-boot = &status_green;
+ led-failsafe = &status_red;
+ led-running = &status_green;
+ led-upgrade = &power_orange;
+ };
+
+ /* Do we really need this defined? */
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ ranges;
+
+ tz_apps@87b80000 {
+ reg = <0x87b80000 0x280000>;
+ reusable;
+ };
+
+ smem@87e00000 {
+ reg = <0x87e00000 0x080000>;
+ no-map;
+ };
+
+ tz@87e80000 {
+ reg = <0x87e80000 0x180000>;
+ no-map;
+ };
+ };
+
+ soc {
+ mdio@90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ phy-reset-gpio = <&tlmm 47 0>;
+ /delete-node/ ethernet-phy@0;
+ /delete-node/ ethernet-phy@2;
+ /delete-node/ ethernet-phy@3;
+ /delete-node/ ethernet-phy@4;
+ };
+
+ /* It is a 56-bit counter that supplies the count to the ARM arch
+ timers and without upstream driver */
+ counter@4a1000 {
+ compatible = "qcom,qca-gcnt";
+ reg = <0x4a1000 0x4>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII_RGMII5>;
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ serial@78af000 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ serial@78b0000 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ bluetooth {
+ compatible = "ti,cc2650";
+ enable-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ switch_mac_mode = <0x3>; /* mac mode for RGMII RMII */
+ switch_lan_bmp = <0x0>; /* lan port bitmap */
+ switch_wan_bmp = <0x10>; /* wan port bitmap */
+ };
+
+ edma@c080000 {
+ qcom,single-phy;
+ qcom,num_gmac = <1>;
+ phy-mode = "rgmii-rxid";
+ status = "okay";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ power_orange: power {
+ label = "mr33:orange:power";
+ gpios = <&tlmm 49 GPIO_ACTIVE_LOW>;
+ panic-indicator;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <1>;
+ qcom,poll_required = <1>;
+ vlan_tag = <0 0x20>;
+};
+
+&i2c_0 {
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ at24@50 {
+ compatible = "atmel,24c64";
+ pagesize = <32>;
+ reg = <0x50>;
+ read-only; /* This holds our MAC & Meraki board-data */
+ };
+};
+
+&i2c_1 {
+ pinctrl-0 = <&i2c_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ lp5562@30 {
+ enable-gpio = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+ compatible = "ti,lp5562";
+ clock-mode = /bits/8 <2>;
+ reg = <0x30>;
+
+ /* RGB led */
+ status_red: chan0 {
+ chan-name = "mr33:red:status";
+ led-cur = /bits/ 8 <0x20>;
+ max-cur = /bits/ 8 <0x60>;
+ };
+
+ status_green: chan1 {
+ chan-name = "mr33:green:status";
+ led-cur = /bits/ 8 <0x20>;
+ max-cur = /bits/ 8 <0x60>;
+ };
+
+ chan2 {
+ chan-name = "mr33:blue:status";
+ led-cur = /bits/ 8 <0x20>;
+ max-cur = /bits/ 8 <0x60>;
+ };
+
+ chan3 {
+ chan-name = "mr33:white:status";
+ led-cur = /bits/ 8 <0x20>;
+ max-cur = /bits/ 8 <0x60>;
+ };
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "sbl1";
+ reg = <0x000000000000 0x000000100000>;
+ read-only;
+ };
+ partition@1 {
+ label = "mibib";
+ reg = <0x000000100000 0x000000100000>;
+ read-only;
+ };
+ partition@2 {
+ label = "bootconfig";
+ reg = <0x000000200000 0x000000100000>;
+ read-only;
+ };
+ partition@3 {
+ label = "qsee";
+ reg = <0x000000300000 0x000000100000>;
+ read-only;
+ };
+ partition@4 {
+ label = "qsee_alt";
+ reg = <0x000000400000 0x000000100000>;
+ read-only;
+ };
+ partition@5 {
+ label = "cdt";
+ reg = <0x000000500000 0x000000080000>;
+ read-only;
+ };
+ partition@6 {
+ label = "cdt_alt";
+ reg = <0x000000580000 0x000000080000>;
+ read-only;
+ };
+ partition@7 {
+ label = "ddrparams";
+ reg = <0x000000600000 0x000000080000>;
+ read-only;
+ };
+ partition@8 {
+ label = "u-boot";
+ reg = <0x000000700000 0x000000200000>;
+ read-only;
+ };
+ partition@9 {
+ label = "u-boot-backup";
+ reg = <0x000000900000 0x000000200000>;
+ read-only;
+ };
+ partition@10 {
+ label = "ART";
+ reg = <0x000000b00000 0x000000080000>;
+ read-only;
+ };
+ partition@11 {
+ label = "ubi";
+ reg = <0x000000c00000 0x000007000000>;
+ };
+ };
+ };
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ /*
+ * GPIO43 should be 0/1 whenever the unit is
+ * powered through PoE or AC-Adapter.
+ * That said, playing with this seems to
+ * reset the AP.
+ */
+
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial1_pinmux {
+ mux {
+ /* We use the i2c-0 pins for serial_1 */
+ pins = "gpio8", "gpio9";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ i2c_0_pins: i2c_0_pinmux {
+ pinmux {
+ function = "blsp_i2c0";
+ pins = "gpio20", "gpio21";
+ };
+ pinconf {
+ pins = "gpio20", "gpio21";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ i2c_1_pins: i2c_1_pinmux {
+ pinmux {
+ function = "blsp_i2c1";
+ pins = "gpio34", "gpio35";
+ };
+ pinconf {
+ pins = "gpio34", "gpio35";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ /*
+ * There are 18 pins. 15 pins are common between LCD and NAND.
+ * The QPIC controller arbitrates between LCD and NAND. Of the
+ * remaining 4, 2 are for NAND and 2 are for LCD exclusively.
+ *
+ * The meraki source hints that the bluetooth module claims
+ * pin 52 as well. But sadly, there's no data whenever this
+ * is a NAND or LCD exclusive pin or not.
+ */
+
+ pullups {
+ pins = "gpio52", "gpio53", "gpio58",
+ "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ /* qcom,ath10k-calibration-variant = "MERAKI-MR33"; */
+};
+
+&wifi1 {
+ status = "okay";
+ /* qcom,ath10k-calibration-variant = "MERAKI-MR33"; */
+};