ipq40xx: add support for EnGenius EAP1300

SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB
NOR:    32 MiB
ETH:    Qualcomm Atheros QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button
LEDS:   Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz

1. Load Ramdisk via U-Boot

To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
   * 115200bps
   * 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.

U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm

2. Load image via GUI

a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.

3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin

Signed-off-by: Steven Lin <steven.lin@senao.com>

3 files changed, 15 insertions, 6 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index ab2f77ee10..5e382c03a7 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -23,6 +23,12 @@ avm,fritzbox-4040)
 	ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
 	ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
 	;;
+engenius,eap1300)
+	ucidef_set_led_netdev "lan" "LAN" "${boardname}:blue:lan" "eth0"
+	ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt"
+	ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:yellow:wlan5g" "phy1tpt"
+	ucidef_set_led_default "mesh" "MESH" "${boardname}:blue:mesh" "0"
+	;;
 glinet,gl-b1300)
 	ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
 	;;
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 5c90ef136f..d73914c7c1 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -33,6 +33,13 @@ avm,fritzbox-4040)
 compex,wpj428)
 	ucidef_set_interface_lan "eth0 eth1"
 	;;
+engenius,eap1300 |\
+meraki,mr33 |\
+netgear,ex6100v2 |\
+netgear,ex6150v2 |\
+zyxel,wre6606)
+	ucidef_set_interface_lan "eth0"
+	;;
 glinet,gl-b1300)
 	ucidef_set_interfaces_lan_wan "eth0" "eth1"
 	ucidef_add_switch "switch0" \
@@ -42,12 +49,6 @@ openmesh,a42 |\
 openmesh,a62)
 	ucidef_set_interfaces_lan_wan "eth1" "eth0"
 	;;
-meraki,mr33 |\
-netgear,ex6100v2 |\
-netgear,ex6150v2 |\
-zyxel,wre6606)
-	ucidef_set_interface_lan "eth0"
-	;;
 zyxel,nbg6617)
 	ucidef_set_interfaces_lan_wan "eth0" "eth1"
 	ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 1d4fd9cd8f..605a03be1d 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -142,6 +142,7 @@ case "$FIRMWARE" in
 		ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 0)
 		;;
 	compex,wpj428 |\
+	engenius,eap1300 |\
 	openmesh,a42 |\
 	openmesh,a62)
 		ath10kcal_extract "0:ART" 4096 12064
@@ -178,6 +179,7 @@ case "$FIRMWARE" in
 		ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 12)
 		;;
 	compex,wpj428 |\
+	engenius,eap1300 |\
 	openmesh,a42 |\
 	openmesh,a62)
 		ath10kcal_extract "0:ART" 20480 12064