ipq40xx: add support for EZVIZ CS-W3-WD1200G EUP

Hardware:
SOC:    Qualcomm IPQ4018
RAM:	128 MB Nanya NT5CC64M16GP-DI
FLASH:  16 MB Macronix MX25L12805D
ETH:    Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN)
WLAN:   Qualcomm IPQ4018 (2.4 & 5 Ghz)
BUTTON: Shared WPS/Reset button
LED:    RGB Status/Power LED
SERIAL: Header J8 (UART, Left side of board). Numbered from
        top to bottom:
        (1) GND, (2) TX, (3) RX, (4) VCC (White triangle
        next to it).
        3.3v, 115200, 8N1

Tested/Working:
* Ethernet
* WiFi (2.4 and 5GHz)
* Status LED
* Reset Button (See note below)

Implementation notes:
* The shared WPS/Reset button is implemented as a Reset button
* I could not find a original firmware image to reverse engineer, meaning
currently it's not possible to flash OpenWrt through the Web GUI.

Installation (Through Serial console & TFTP):
1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to
one of the LAN ports
2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on
your pc, to serve the image
2. Connect to the router through serial (See connection properties above)
3. Hit a key during startup, to pause startup
4. type `setenv serverip 192.168.1.12`, to set the tftp server address
5. type `tftpboot`, to load the image from the laptop through tftp
6. type `bootm` to run the loaded image from memory
6. (If you want to return to stock firmware later, create an full MTD backup,
e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup)
7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.:
`scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin`
8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin`

Revert to stock:
To revert to stock, you need the MTD backup from step 6 above:
1. Unpack the MTD backup archive
2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup)
3. On the router, do `mtd write mtd8_firmware.backup firmware`

Signed-off-by: Tom Brouwer <tombrouwer@outlook.com>
[removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

4 files changed, 15 insertions, 0 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index ae8cb2efe7..57caa88c85 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -54,6 +54,11 @@ ipq40xx_setup_interfaces()
 	compex,wpj428)
 		ucidef_set_interface_lan "eth0 eth1"
 		;;
+	ezviz,cs-w3-wd1200g-eup)
+		ucidef_set_interfaces_lan_wan "eth0" "eth1"
+		ucidef_add_switch "switch0" \
+			"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "0u@eth1" "5:wan"
+		;;
 	glinet,gl-b1300)
 		ucidef_set_interfaces_lan_wan "eth0" "eth1"
 		ucidef_add_switch "switch0" \
@@ -97,6 +102,9 @@ ipq40xx_setup_macs()
 		wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
 		lan_mac=$(macaddr_add "$wan_mac" 1)
 		;;
+	ezviz,cs-w3-wd1200g-eup)
+		label_mac=$(mtd_get_mac_binary "ART" 0x6)
+		;;
 	linksys,ea6350v3)
 		wan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
 		lan_mac=$(macaddr_add "$wan_mac" 1)
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 8b6abc4ff7..3616bff578 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -46,6 +46,7 @@ case "$FIRMWARE" in
 	8dev,jalapeno |\
 	alfa-network,ap120c-ac |\
 	cilab,meshpoint-one |\
+	ezviz,cs-w3-wd1200g-eup |\
 	glinet,gl-b1300 |\
 	linksys,ea6350v3 |\
 	qcom,ap-dk01.1-c1)
@@ -115,6 +116,7 @@ case "$FIRMWARE" in
 	8dev,jalapeno |\
 	alfa-network,ap120c-ac |\
 	cilab,meshpoint-one |\
+	ezviz,cs-w3-wd1200g-eup |\
 	glinet,gl-b1300 |\
 	linksys,ea6350v3 |\
 	qcom,ap-dk01.1-c1)
diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
index 192488f377..1bca152a38 100644
--- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
+++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
@@ -9,6 +9,10 @@ preinit_set_mac_address() {
 		ip link set dev eth0 address $(macaddr_add "$base_mac" +1)
 		ip link set dev eth1 address $(macaddr_add "$base_mac" +3)
 		;;
+	ezviz,cs-w3-wd1200g-eup)
+		ip link set dev eth0 address $(mtd_get_mac_binary "ART" 0x6)
+		ip link set dev eth1 address $(mtd_get_mac_binary "ART" 0x0)
+		;;
 	linksys,ea8300)
 		base_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
 		ip link set dev eth0 address "${base_mac}"
diff --git a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh
index a0dec1042a..42667d2dfb 100644
--- a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh
+++ b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh
@@ -7,6 +7,7 @@ set_preinit_iface() {
 	aruba,ap-303| \
 	asus,rt-ac58u| \
 	avm,fritzbox-4040| \
+	ezviz,cs-w3-wd1200g-eup| \
 	glinet,gl-b1300| \
 	linksys,ea8300| \
 	meraki,mr33| \