aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/base-files
diff options
context:
space:
mode:
authorDavid Bauer <mail@david-bauer.net>2018-03-29 00:32:38 +0200
committerMathias Kresin <dev@kresin.me>2018-04-13 07:48:19 +0200
commit970f1914be3f299fb302ca74a214589397000858 (patch)
tree5b7a7d0ffe4b0cc774ca5b027351bbdcf1472986 /target/linux/ipq40xx/base-files
parentbe6e28b516be2701bb734b11fe39d739207e9186 (diff)
downloadupstream-970f1914be3f299fb302ca74a214589397000858.tar.gz
upstream-970f1914be3f299fb302ca74a214589397000858.tar.bz2
upstream-970f1914be3f299fb302ca74a214589397000858.zip
ipq40xx: add support for Netgear EX6100v2/EX6150v2
Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MB Winbond W632GU6KB12J FLASH: 16 MiB Macronix MX25L12805D ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 1x1 (EX6100) 2x2 (EX6150) INPUT: Power, WPS, reset button AP / Range-extender toggle LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow SERIAL: Header next to QCA8072 chip. VCC, TX, RX, GND (Square hole is VCC) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from WebIF - Factory installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Not Working: - AP/Extender toggle-switch Untested: - Support on EX6100v2. They share the same GPL-Code and vendor-images. The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz board-blob. I only own a EX6150v2, therefore i am only able to verify functionality on this device. Install via Web-Interface: Upload the factory image to the device to the Netgear Web-Interface. The device might asks you to confirm the update a second time due to detecting the OpenWRT firmware as older. The device will automatically reboot after the image is written to flash. Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command "fw_recovery" will start a tftp server, waiting for a DNI image to be pushed. Assign your computer the IP-address 192.168.1.10/24. Push image with tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY> Device will erase factory-partition first, then writes the pushed image to flash and reboots. Parts of this commit are based on Thomas Hebb's work on the openwrt-devel mailinglist. See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html Signed-off-by: David Bauer <mail@david-bauer.net>
Diffstat (limited to 'target/linux/ipq40xx/base-files')
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/01_leds5
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/02_network5
-rw-r--r--target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata10
3 files changed, 18 insertions, 2 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index f1f49abb2e..784fd444dd 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -26,6 +26,11 @@ avm,fritzbox-4040)
glinet,gl-b1300)
ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
;;
+netgear,ex6100v2 |\
+netgear,ex6150v2)
+ ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt"
+ ucidef_set_led_wlan "wlan5g" "WLAN5G" "ex61x0v2:green:client" "phy1tpt"
+ ;;
meraki,mr33)
ucidef_set_interface_lan "eth0"
;;
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 91343cd4b4..ade1b05458 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -41,8 +41,9 @@ glinet,gl-b1300)
openmesh,a42)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
-
-meraki,mr33)
+meraki,mr33 |\
+netgear,ex6100v2 |\
+netgear,ex6150v2)
ucidef_set_interface_lan "eth0"
;;
*)
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 56c10cbf00..0a5780cbf0 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -129,6 +129,11 @@ case "$FIRMWARE" in
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064
ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +2)
;;
+ netgear,ex6100v2 |\
+ netgear,ex6150v2)
+ ath10kcal_extract "ART" 4096 12064
+ ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 0)
+ ;;
compex,wpj428 |\
openmesh,a42)
ath10kcal_extract "0:ART" 4096 12064
@@ -154,6 +159,11 @@ case "$FIRMWARE" in
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064
ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +3)
;;
+ netgear,ex6100v2 |\
+ netgear,ex6150v2)
+ ath10kcal_extract "ART" 20480 12064
+ ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 12)
+ ;;
compex,wpj428 |\
openmesh,a42)
ath10kcal_extract "0:ART" 20480 12064