ipq40xx: add support for AVM FRITZ!Repeater 1200

Hardware
--------
SoC:   Qualcomm IPQ4019
RAM:   256M DDR3
FLASH: 128M NAND
WiFi:  2T2R IPQ4019 bgn
       2T2R IPQ4019 a/n/ac
ETH:   Atheros AR8033 RGMII PHY
BTN:   1x Connect (WPS)
LED:   Power (green/red/yellow)

Installation
------------

1. Grab the uboot for the Device from the 'u-boot-fritz1200'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ1200.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz1200.bin uboot0
   > mtd write /path/to/uboot-fritz1200.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>

2 files changed, 7 insertions, 4 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index f036dc842f..25402b7eb4 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -39,10 +39,7 @@ ipq40xx_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
 		;;
-	avm,fritzrepeater-3000|\
-	compex,wpj428)
-		ucidef_set_interface_lan "eth0 eth1"
-		;;
+	avm,fritzrepeater-1200|\
 	engenius,eap1300|\
 	meraki,mr33|\
 	netgear,ex6100v2|\
@@ -50,6 +47,10 @@ ipq40xx_setup_interfaces()
 	zyxel,wre6606)
 		ucidef_set_interface_lan "eth0"
 		;;
+	avm,fritzrepeater-3000|\
+	compex,wpj428)
+		ucidef_set_interface_lan "eth0 eth1"
+		;;
 	glinet,gl-b1300)
 		ucidef_set_interfaces_lan_wan "eth0" "eth1"
 		ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index e82ffbea9d..2336ef3c7b 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -61,6 +61,7 @@ case "$FIRMWARE" in
 		/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
 		;;
 	avm,fritzbox-7530 |\
+	avm,fritzrepeater-1200 |\
 	avm,fritzrepeater-3000)
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
@@ -123,6 +124,7 @@ case "$FIRMWARE" in
 		/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
 		;;
 	avm,fritzbox-7530 |\
+	avm,fritzrepeater-1200 |\
 	avm,fritzrepeater-3000)
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \