aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/base-files/etc/hotplug.d
diff options
context:
space:
mode:
authorDavid Bauer <mail@david-bauer.net>2019-10-23 22:25:14 +0200
committerDavid Bauer <mail@david-bauer.net>2019-12-20 17:48:52 +0100
commit102c8c55f217606cdbdc9a449667e034676b3e75 (patch)
tree8f7736a01ad3e77a4dba8b2ee2db9fabf89cb685 /target/linux/ipq40xx/base-files/etc/hotplug.d
parent4113d8a2554adf5ecee55cc07956eafad378eaff (diff)
downloadupstream-102c8c55f217606cdbdc9a449667e034676b3e75.tar.gz
upstream-102c8c55f217606cdbdc9a449667e034676b3e75.tar.bz2
upstream-102c8c55f217606cdbdc9a449667e034676b3e75.zip
ipq40xx: add support for Aruba AP-303
Hardware -------- SoC: Qualcomm IPQ4029 RAM: 512M DDR3 FLASH: - 128MB NAND (Macronix MX30LF1G18AC) - 4MB SPI-NOR (Macronix MX25R3235F) TPM: Atmel AT97SC3203 BLE: Texas Instruments CC2540T attached to ttyMSM0 ETH: Atheros AR8035 LED: WiFi (amber / green) System (red / green) BTN: Reset To connect to the serial console, you can solder to the labled pads next to the USB port or use your Aruba supplied UARt adapter. Do NOT plug a standard USB cable into the Console labled USB-port! Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself an adapter cable: VCC - NC D+ - TX D- - RX GND - GND The console setting in bootloader and OS is 9600 8N1. Voltage level is 3.3V. To enable a full list of commands in the U-Boot "help" command, execute the literal "diag" command. Installation ------------ 1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it into the TFTP server root directory. Configure the TFTP server to be reachable at 192.168.1.75/24. Connect the machine running the TFTP server to the ethernet port of the access point. 2. Connect to the serial console. Interrupt autobooting by pressing Enter when prompted. 3. Configure the bootargs and bootcmd for OpenWrt. $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8" $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1; ubi read 0x85000000 kernel; bootm 0x85000000" $ setenv ramboot_openwrt "run bootargs_openwrt; setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75; netget; set fdt_high 0x87000000; bootm" $ setenv bootcmd "run nandboot_openwrt" $ saveenv 4. Load OpenWrt into RAM: $ run ramboot_openwrt 5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the /tmp folder on the device. 6. Flash OpenWrt: $ ubidetach -p /dev/mtd1 $ ubiformat /dev/mtd1 $ sysupgrade -n /tmp/openwrt-sysupgrade.bin To go back to the stock firmware, simply reset the bootcmd in the bootloader to the original value: $ setenv bootcmd "boot" $ saveenv Signed-off-by: David Bauer <mail@david-bauer.net>
Diffstat (limited to 'target/linux/ipq40xx/base-files/etc/hotplug.d')
-rw-r--r--target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata8
1 files changed, 8 insertions, 0 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 3d46519415..8b6abc4ff7 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -51,6 +51,10 @@ case "$FIRMWARE" in
qcom,ap-dk01.1-c1)
caldata_extract "ART" 0x1000 0x2f20
;;
+ aruba,ap-303)
+ caldata_extract "ART" 0x1000 0x2f20
+ ath10k_patch_mac $(mtd_get_mac_binary mfginfo 0x1D)
+ ;;
asus,map-ac2200)
caldata_extract_ubi "Factory" 0x1000 0x2f20
;;
@@ -116,6 +120,10 @@ case "$FIRMWARE" in
qcom,ap-dk01.1-c1)
caldata_extract "ART" 0x5000 0x2f20
;;
+ aruba,ap-303)
+ caldata_extract "ART" 0x5000 0x2f20
+ ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mfginfo 0x1D) +1)
+ ;;
asus,map-ac2200)
caldata_extract_ubi "Factory" 0x5000 0x2f20
;;