diff options
| author | Roger Pueyo Centelles <roger.pueyo@guifi.net> | 2020-10-23 16:05:28 +0200 |
|---|---|---|
| committer | Paul Spooren <mail@aparcar.org> | 2021-04-29 10:55:07 +0200 |
| commit | d1f1e5269ed992e6fc30d575b43b0913c9e58ca2 (patch) | |
| tree | 4836c37b12b7dc4d4575446d5e240ace98f0469f /target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | |
| parent | 43dad22025597cb535626757301e035187d02b25 (diff) | |
| download | upstream-d1f1e5269ed992e6fc30d575b43b0913c9e58ca2.tar.gz upstream-d1f1e5269ed992e6fc30d575b43b0913c9e58ca2.tar.bz2 upstream-d1f1e5269ed992e6fc30d575b43b0913c9e58ca2.zip | |
ipq40xx: add support for MikroTik SXTsq 5 ac
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Diffstat (limited to 'target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata')
| -rw-r--r-- | target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 3 |
1 files changed, 2 insertions, 1 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 0e027dd0a5..b12c9af9a7 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -249,7 +249,8 @@ case "$FIRMWARE" in caldata_valid "202f" || caldata_extract "ART" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) +3) ;; - mikrotik,hap-ac2) + mikrotik,hap-ac2|\ + mikrotik,sxtsq-5-ac) wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data" ( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x8000 0x2f20 ) || \ ( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_2" 0x0 0x2f20 ) |