diff options
author | Felix Matouschek <felix@matouschek.org> | 2021-07-15 21:48:11 +0200 |
---|---|---|
committer | Hauke Mehrtens <hauke@hauke-m.de> | 2021-11-28 18:39:01 +0100 |
commit | 1cc3b95efcc616fba91a7f34e9781743229cc640 (patch) | |
tree | f412fc5d20cbc34fdda146b87a17032ce3bd4352 /target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | |
parent | 67f52012760ce553ba6393aaba77359a458deeda (diff) | |
download | upstream-1cc3b95efcc616fba91a7f34e9781743229cc640.tar.gz upstream-1cc3b95efcc616fba91a7f34e9781743229cc640.tar.bz2 upstream-1cc3b95efcc616fba91a7f34e9781743229cc640.zip |
ipq40xx: Add support for Teltonika RUTX10
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.
The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.
See https://teltonika-networks.com/product/rutx10 for more info.
Hardware:
SoC: Qualcomm IPQ4018
RAM: 256MB DDR3
SPI Flash 1: XTX XT25F128B (16MB, NOR)
SPI Flash 2: XTX XT26G02AWS (256MB, NAND)
Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
USB Hub: Genesys Logic GL852GT
Bluetooth: Qualcomm CSR8510 (A10U)
LED/GPIO controller: STM32F030 with custom firmware
Buttons: Reset button
Leds: Power (green, cannot be controlled)
WiFi 2.4G activity (green)
WiFi 5G activity (green)
MACs Details verified with the stock firmware:
eth0: Partition 0:CONFIG Offset: 0x0
eth1: = eth0 + 1
radio0 (2.4 GHz): = eth0 + 2
radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.
The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt
USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.
Flash instructions via stock web interface (sysupgrade based):
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
5. Open stock web interface at http://192.168.1.1
6. Set some password so the web interface is happy
7. Go to firmware upgrade settings
8. Choose
openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
9. Set 'Keep settings' to off
10. Click update, when warned that it is not a signed image proceed
Return to stock firmware:
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
Diffstat (limited to 'target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata')
-rw-r--r-- | target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 8 |
1 files changed, 8 insertions, 0 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 1e1b445924..f43a3a88b7 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -166,6 +166,10 @@ case "$FIRMWARE" in caldata_extract "0:ART" 0x1000 0x2f20 ath10k_patch_mac $(mtd_get_mac_binary "0:MANUDATA" 0x6) ;; + teltonika,rutx10) + caldata_extract "0:ART" 0x1000 0x2f20 + ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:CONFIG" 0x0) 2) + ;; zyxel,nbg6617 |\ zyxel,wre6606) caldata_extract "ART" 0x1000 0x2f20 @@ -285,6 +289,10 @@ case "$FIRMWARE" in caldata_extract "0:ART" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:MANUDATA" 0x6) 16) ;; + teltonika,rutx10) + caldata_extract "0:ART" 0x5000 0x2f20 + ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:CONFIG" 0x0) 3) + ;; zyxel,nbg6617 |\ zyxel,wre6606) caldata_extract "ART" 0x5000 0x2f20 |