ipq40xx: add support for Cell C RTL30VW

Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated
QMI mPCIE modem.

This is stripped version of ASKEY RTL0030VW.

Hardware:

Specification:
-CPU: IPQ4019
-RAM: 256MB
-Flash: NAND 128MB + NOR 16MB
-WiFi: Integrated bgn/ac
-LTE: mPCIe card (Modem chipset MDM9230)
-LAN: 2 Gigabit Ports
-USB: 2x USB2.0
-Serial console: RJ-45 115200 8n1
-Unsupported VoIP

Known issues:

None so far.

Instruction install:

There are two methods: Factory web-gui and serial + tftp.

Web-gui:
1. Apply factory image via stock web-gui.

Serial + initramfs:
1. Rename OpenWrt initramfs image to "image"
2. Connect serial console (115200,8n1)
3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4.

4. U-Boot commands:
sf probe && sf read 0x80000000 0x180000 0x10000
setenv serverip 192.168.1.4
set fdt_high 0x85000000
tftpboot 0x84000000 image
bootm 0x84000000

5. Install sysupgrade image via "sysupgrade -n"

Back to stock:

All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0,
do firstboot and factory reset with OFW:

1. read mtd8:
dd if=/dev/mtd8 of=/tmp/mtd8
2. go to tmp:
cd /tmp/
3. write first part of partition:
dd if=mtd8 of=mtd8.new bs=1 count=76
4. check which layout uses bootloader:
cat /proc/mtd
5a. If first are kernel_1 and rootfs_1 write 0:
echo -n -e '\x00' >> mtd8.new
5b. If first are kernel and rootfs write 1:
echo -n -e '\x01' >> mtd8.new
6. fill with rest of data:
dd if=mtd8 bs=1 skip=77 >> mtd8.new
7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with:
hexdump mtd8.new
8. write new mtd8 to flash:
mtd write mtd8.new /dev/mtd8
9. do firstboot
10.reboot
11. Do back to factory defaults in OFW GUI.

Based on work: Cezary Jackiewicz <cezary@eko.one.pl>

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>

2 files changed, 11 insertions, 0 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 13e2722f79..0e4b947c5f 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -63,6 +63,11 @@ ipq40xx_setup_interfaces()
 	engenius,eap2200)
 		ucidef_set_interface_lan "eth0 eth1"
 		;;
+	cellc,rtl30vw)
+		ucidef_set_interface_lan "eth0"
+		ucidef_add_switch "switch0" \
+			"0u@eth0" "3:lan" "4:lan"
+		;;
 	ezviz,cs-w3-wd1200g-eup)
 		ucidef_set_interfaces_lan_wan "eth0" "eth1"
 		ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
index e46a297ea7..c255707f91 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
+++ b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
@@ -7,6 +7,12 @@ board_config_update
 board=$(board_name)
 
 case "$board" in
+cellc,rtl30vw)
+	ucidef_add_gpio_switch "w_disable" "W_DISABLE mPCIE pin" "398" "1"
+	ucidef_add_gpio_switch "pmd_resin_n" "PMD_RESIN_N pin" "399" "1"
+	ucidef_add_gpio_switch "mcpie_vcc" "LTE power" "400" "0"
+	ucidef_add_gpio_switch "usb_vcc" "USB power" "401" "0"
+	;;
 cilab,meshpoint-one)
 	ucidef_add_gpio_switch "poe_passtrough" "POE passtrough enable" "413" "1"
 	;;