ipq40xx: add support for Qxwlan E2600AC C1 and C2

Qxwlan E2600AC C1 based on IPQ4019

Specifications:
SOC:	Qualcomm IPQ4019
DRAM:	256 MiB
FLASH:	32 MiB Winbond W25Q256
ETH:	Qualcomm QCA8075
WLAN:	5G + 5G/2.4G
	* 2T2R 2.4/5 GHz
	 - QCA4019 hw1.0 (SoC)
	* 2T2R 5 GHz
	 - QCA4019 hw1.0 (SoC)
INPUT:  Reset buutton
LED:	1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB:	USB3.0
POWER:	1x DC jack for main power input (9-24 V)
SLOT:	Pcie (J25), sim card (J11), SD card (J51)

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Qxwlan E2600AC C2 based on IPQ4019

Specifications:
SOC:	Qualcomm IPQ4019
DRAM:	256 MiB
NOR:	16 MiB Winbond W25Q128
NAND:	128MiB Micron MT29F1G08ABAEAWP
ETH:	Qualcomm QCA8075
WLAN:	5G + 5G/2.4G
	* 2T2R 2.4/5 GHz
	 - QCA4019 hw1.0 (SoC)
	* 2T2R 5 GHz
	 - QCA4019 hw1.0 (SoC)
INPUT:  Reset buutton
LED:	1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB:	USB3.0
POWER:	1x DC jack for main power input (9-24 V)
SLOT:	Pcie (J25), sim card (J11), SD card (J51)

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "ubi" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

1 files changed, 5 insertions, 0 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index 2fca1cbc9f..d23791eab1 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -39,6 +39,11 @@ netgear,ex6150v2)
 	ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt"
 	ucidef_set_led_wlan "wlan5g" "WLAN5G" "ex61x0v2:green:client" "phy1tpt"
 	;;
+qxwlan,e2600ac-c1 |\
+qxwlan,e2600ac-c2)
+	ucidef_set_led_wlan "wlan2g" "WLAN0" "e2600ac:green:wlan0" "phy0tpt"
+	ucidef_set_led_wlan "wlan5g" "WLAN1" "e2600ac:green:wlan1" "phy1tpt"
+	;;
 zyxel,nbg6617)
 	ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2G" "phy0tpt"
 	ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5G" "phy1tpt"