imx6: drop 4.1 support

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 48300

2 files changed, 0 insertions, 1073 deletions

diff --git a/target/linux/imx6/files-4.1/drivers/net/phy/gw16083.c b/target/linux/imx6/files-4.1/drivers/net/phy/gw16083.c
deleted file mode 100644
index e41577b684..0000000000
--- a/target/linux/imx6/files-4.1/drivers/net/phy/gw16083.c
+++ /dev/null
@@ -1,950 +0,0 @@
-/*
- * drivers/net/phy/gw16083.c
- *
- * Driver for GW16083 Ventana Ethernet Expansion Mezzanine
- *
- * Author: Tim Harvey
- *
- * Copyright (c) 2014 Tim Harvey <tharvey@gateworks.com>
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- *
- */
-
-/*
- * The GW16083 interfaces with a Ventana baseboard via the PCIe bus, an i2c
- * bus (i2c2), and a couple of GPIO's. On the PCIe bus is an i210 GigE with
- * its MAC connected to Port4 of a Marvell MV88E6176 7-port GigE switch via
- * MDIO and RGMII. Ports 0-3 are standard copper RJ45 but Ports 5 and 6
- * connect to Marvell MV88E1111 dual-mode Copper/Fiber PHY's over SGMII and
- * MDIO. The PHY's have both an RG45 for copper and an SFP module.
- */
-
-#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/unistd.h>
-#include <linux/i2c.h>
-#include <linux/interrupt.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/device.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/spinlock.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/mii.h>
-#include <linux/ethtool.h>
-#include <linux/phy.h>
-#include <linux/marvell_phy.h>
-#include <linux/of_platform.h>
-
-#include <linux/io.h>
-#include <asm/irq.h>
-#include <linux/uaccess.h>
-
-#include "gw16083.h"
-
-#undef FAIL_ON_CHECKSUM_ERR	/* fail to configure SFP if checksum bad */
-#define PORT_POWER_CONTROL	/* ports can be enabled/disabled via sysfs */
-#define PORT_MODE_CONTROL	/* ports 5/6 can have SFP/RJ45 mode forced */
-
-MODULE_DESCRIPTION("GW16083 driver");
-MODULE_AUTHOR("Tim Harvey");
-MODULE_LICENSE("GPL");
-
-struct mv88e1111_port_state {
-	int port;
-	bool present;
-	bool serdes;
-	bool sfp_signal;
-	bool sfp_present;
-	bool sfp_compat;
-	bool sfp_enabled;
-	char sfp_id[64];
-};
-
-struct mv88e1111_priv {
-	struct phy_device		*phydev;
-	struct i2c_client		*client;
-	struct mv88e1111_port_state	port5;
-	struct mv88e1111_port_state	port6;
-	struct kobject			*sysfs_kobj;
-};
-
-enum {
-	mode_copper = 0,
-	mode_serdes = 1,
-};
-
-static struct i2c_client *gw16083_client = NULL;
-
-static int gw16083_read_port_sfp(struct i2c_client *client,
-				 struct mv88e1111_port_state *state);
-
-/* read switch port register from port0-6 */
-u16 read_switch_port(struct phy_device *pdev, int port, u8 regaddr)
-{
-	return pdev->bus->read(pdev->bus, MV_BASE + port, regaddr);
-}
-
-/* write switch port register to port0-6 */
-int write_switch_port(struct phy_device *pdev, int port, u8 regaddr, u16 val)
-{
-	return pdev->bus->write(pdev->bus, MV_BASE + port, regaddr, val);
-}
-
-/*
- * read_switch_port_phy - write a register for a specific port on 88E6176
- * The 88E6176 PHY registers must be accessed thorugh the Global2 address
- * using the SMI_PHY_COMMAND_REG and SMI_PHY_DATA_REG.
- */
-int read_switch_port_phy(struct phy_device *pdev, int port, u8 regaddr)
-{
-	u16 reg;
-	int i;
-
-	dev_dbg(&pdev->dev, "read_phy: port%d reg=0x%02x\n", port, regaddr);
-	reg = SMIBUSY | SMIMODE22 | SMIOP_READ;
-	reg |= port << DEVADDR;
-	reg |= regaddr << REGADDR;
-	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_COMMAND, reg);
-	for (i = 0; i < 10; i++) {
-		reg = pdev->bus->read(pdev->bus, MV_GLOBAL2,
-				      MV_SMI_PHY_COMMAND);
-		if (!(reg & (1<<15)))
-			break;
-		mdelay(1);
-	}
-	/* timeout */
-	if (i == 10)
-		return 0xffff;
-	reg = pdev->bus->read(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_DATA);
-	return reg;
-}
-
-/*
- * write_switch_port_phy - write a register for a specific port on 88E6176
- * The 88E6176 PHY registers must be accessed thorugh the Global2 address
- * using the SMI_PHY_COMMAND_REG and SMI_PHY_DATA_REG.
- */
-int write_switch_port_phy(struct phy_device *pdev, int port, u8 addr, u16 reg)
-{
-	int i;
-
-	dev_dbg(&pdev->dev, "write_phy: port%d reg=0x%02x val=0x%04x\n", port,
-		addr, reg);
-	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_DATA, reg);
-	reg = SMIBUSY | SMIMODE22 | SMIOP_WRITE;
-	reg |= port << DEVADDR;
-	reg |= addr << REGADDR;
-	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_COMMAND, reg);
-	for (i = 0; i < 10; i++) {
-		reg = pdev->bus->read(pdev->bus, MV_GLOBAL2,
-				      MV_SMI_PHY_COMMAND);
-		if (!(reg & (1<<15)))
-			break;
-		mdelay(1);
-	}
-	/* timeout */
-	if (i == 10)
-		return -ETIMEDOUT;
-
-	return 0;
-}
-
-/* read a scratch register from switch */
-inline u8 read_switch_scratch(struct phy_device *pdev, u8 reg)
-{
-	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC, (reg << 8));
-	return pdev->bus->read(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC) & 0xff;
-}
-
-/* write a scratch register to switch */
-inline void write_switch_scratch(struct phy_device *pdev, u8 reg, u8 val)
-{
-	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC,
-			 (1 << 15) | (reg << 8) | val);
-}
-
-/* enable or disable an SFP's TXEN signal */
-static int enable_sfp_txen(struct phy_device *pdev, int port, bool enable)
-{
-	u8 gpio;
-	int bit;
-
-	if (port != 5 && port != 6)
-		return -EINVAL;
-
-	/* GPIO[2:1] output low to enable TXEN */
-	bit = (port == 5) ? 1 : 2;
-	gpio = read_switch_scratch(pdev, MV_GPIO_DATA);
-	if (enable)
-		gpio |= (1 << bit);
-	else
-		gpio &= (1 << bit);
-	write_switch_scratch(pdev, MV_GPIO_DATA, gpio);
-	dev_info(&pdev->dev, "Port%d: SFP TX %s\n", port, enable ?
-		 "enabled" : "disabled");
-	return 0;
-}
-
-/* configure mv88e1111 port for copper or serdes
- *  For Copper we set auto link/duplex/speed detection
- *  For SerDes/Fiber we force 1000mbps link up and auto-neg duplex
- */
-static int config_mv88e1111_port_sfp(struct phy_device *pdev, int port,
-				     bool sfp)
-{
-	u16 reg;
-
-	if (port != 5 && port != 6)
-		return -EINVAL;
-
-	dev_dbg(&pdev->dev, "%s: Port%d %s\n", __func__, port,
-		sfp ? "SFP" : "copper");
-	if (sfp) {
-		enable_sfp_txen(pdev, port, 1);
-
-		/* configure MV88E6176 Physical Control Port Register */
-		dev_info(&pdev->dev,
-			 "Port%d: SFP: force 1000mbps link up "
-			 "(auto-negotiate duplex)\n",
-			 port);
-		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
-		reg &= ~0x3f; /* clear 5-0 */
-		reg |= (1 << 4) | (1 << 5); /* force link up */
-		reg |= 2; /* force 1000mbps */
-		write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, reg);
-		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
-	}
-
-	/* copper */
-	else {
-		enable_sfp_txen(pdev, port, 0);
-
-		/* configure MV88E6176 Physical Control Port Register */
-		dev_info(&pdev->dev,
-			 "Port%d: Copper: set auto-neg link/duplex/speed\n",
-			 port);
-		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
-		reg &= ~0x3f; /* clear 5-0 */
-		reg |= 3; /* speed not forced */
-		write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, reg);
-		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
-	}
-	dev_dbg(&pdev->dev, "%s: Port%d %s PORT_PHYS_CONTROL=0x%04x\n",
-		__func__, port, sfp ? "SFP" : "copper",
-		read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL));
-
-	return 0;
-}
-
-#if defined(PORT_POWER_CONTROL)
-static int enable_switch_port(struct phy_device *pdev, int port, bool enable)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
-	u16 reg;
-
-	/* power up port */
-	dev_info(&priv->client->dev, "Port%d: %s\n", port,
-		 enable ? "normal operation" : "power down");
-	reg = read_switch_port_phy(pdev, port, MV_PHY_CONTROL);
-	if (enable)
-		reg &= ~(1 << 11);	/* Normal Operation */
-	else
-		reg |= (1 << 11);	/* power down */
-	write_switch_port_phy(pdev, port, MV_PHY_CONTROL, reg);
-
-	reg = read_switch_port_phy(pdev, port, MV_PHY_CONTROL1);
-	if (enable)
-		reg &= ~(1 << 2);	/* Normal Operation */
-	else
-		reg |= (1 << 2);	/* power down */
-	write_switch_port_phy(pdev, port, MV_PHY_CONTROL1, reg);
-
-	return 0;
-}
-#endif
-
-/*
- * Sysfs API
- */
-
-struct mv88e1111_port_state *get_port_state(struct mv88e1111_priv *priv,
-					    int port)
-{
-	if (port == 5)
-		return &priv->port5;
-	if (port == 6)
-		return &priv->port6;
-	return NULL;
-}
-
-/*
- * get MV88E6176 port number for a specific GW16083 port name
- *  The GW16083 ports as shown on the silkscreen are not mapped according to
- *  the MV88E6176 ports numbers.
- */
-static int gw16083_get_port(const char* name)
-{
-	int i;
-	int map[] = { 3, 2, 1, 0, 5, 6 };
-
-	if (strncasecmp(name, "ETHERNET", 8) != 0 || strlen(name) != 9)
-		return -1;
-	i = name[8] - '0';
-	if (i < 1 || i > 6)
-		return -1;
-	return map[i-1];
-}
-
-static ssize_t port_show(struct device *dev, struct device_attribute *attr,
-			 char *buf)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
-	int port = -1;
-	u16 reg;
-
-	if (sscanf(attr->attr.name, "port%d", &port) != 1)
-		return 0;
-	if (port < 0 || port > 6)
-		return 0;
-	reg = read_switch_port_phy(priv->phydev, port, MV_PHY_CONTROL);
-	return sprintf(buf, "%s\n", (reg & (1 << 11)) ? "disabled" : "enabled");
-}
-
-#if defined(PORT_POWER_CONTROL)
-static ssize_t port_store(struct device *dev, struct device_attribute *attr,
-			  const char *buf, size_t count)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
-	int port = -1;
-	int val;
-
-	port = gw16083_get_port(attr->attr.name);
-	if (port < 0)
-		return 0;
-	if (sscanf(buf, "%d", &val) != 1)
-		return 0;
-	enable_switch_port(priv->phydev, port, val ? 1 : 0);
-	return count;
-}
-
-static DEVICE_ATTR(ethernet1, S_IWUSR | S_IRUGO, port_show, port_store);
-static DEVICE_ATTR(ethernet2, S_IWUSR | S_IRUGO, port_show, port_store);
-static DEVICE_ATTR(ethernet3, S_IWUSR | S_IRUGO, port_show, port_store);
-static DEVICE_ATTR(ethernet4, S_IWUSR | S_IRUGO, port_show, port_store);
-static DEVICE_ATTR(ethernet5, S_IWUSR | S_IRUGO, port_show, port_store);
-static DEVICE_ATTR(ethernet6, S_IWUSR | S_IRUGO, port_show, port_store);
-#else
-static DEVICE_ATTR(ethernet1, S_IRUGO, port_show, NULL);
-static DEVICE_ATTR(ethernet2, S_IRUGO, port_show, NULL);
-static DEVICE_ATTR(ethernet3, S_IRUGO, port_show, NULL);
-static DEVICE_ATTR(ethernet4, S_IRUGO, port_show, NULL);
-static DEVICE_ATTR(ethernet5, S_IRUGO, port_show, NULL);
-static DEVICE_ATTR(ethernet6, S_IRUGO, port_show, NULL);
-#endif
-
-static ssize_t portsfp_show(struct device *dev, struct device_attribute *attr,
-			     char *buf)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
-	struct mv88e1111_port_state *state;
-
-	state = get_port_state(priv, gw16083_get_port(attr->attr.name));
-	if (!state)
-		return 0;
-
-	if (!state->sfp_present)
-		return 0;
-
-	return sprintf(buf, "%s\n", state->sfp_id);
-}
-
-static ssize_t portmode_show(struct device *dev, struct device_attribute *attr,
-			     char *buf)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
-	struct mv88e1111_port_state *state;
-
-	state = get_port_state(priv, gw16083_get_port(attr->attr.name));
-	if (!state)
-		return 0;
-
-	return sprintf(buf, "%s\n", state->serdes ? "SFP" : "RJ45");
-}
-static DEVICE_ATTR(ethernet5_sfp, S_IRUGO, portsfp_show, NULL);
-static DEVICE_ATTR(ethernet6_sfp, S_IRUGO, portsfp_show, NULL);
-
-#ifdef PORT_MODE_CONTROL
-static ssize_t portmode_store(struct device *dev, struct device_attribute *attr,
-			      const char *buf, size_t count)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
-	struct mv88e1111_port_state *state;
-	u16 reg;
-	int port;
-
-	port = gw16083_get_port(attr->attr.name);
-	state = get_port_state(priv, port);
-	if (!state)
-		return 0;
-
-	reg = read_switch_port_phy(priv->phydev, port, MII_M1111_PHY_EXT_SR);
-	if (strcasecmp(buf, "auto") == 0) {
-		reg &= ~(1<<15); /* enable auto-selection */
-		dev_info(&priv->client->dev, "Port%d: enable auto-selection\n",
-			 port);
-	} else if (strcasecmp(buf, "RJ45") == 0) {
-		reg |= (1<<15); /* disable auto-selection */
-		reg |= 0xb; /* RGMII to Copper */
-		config_mv88e1111_port_sfp(priv->phydev, port, 0);
-		dev_info(&priv->client->dev, "Port%d: select RJ45\n", port);
-	} else if (strcasecmp(buf, "SFP") == 0) {
-		reg |= (1<<15); /* disable auto-selection */
-		reg |= 0x3; /* RGMII to Fiber */
-		config_mv88e1111_port_sfp(priv->phydev, port, 1);
-		dev_info(&priv->client->dev, "Port%d: select SFP\n", port);
-	}
-	write_switch_port_phy(priv->phydev, port, MII_M1111_PHY_EXT_SR, reg);
-
-	return count;
-}
-
-static DEVICE_ATTR(ethernet5_mode, S_IWUSR | S_IRUGO, portmode_show,
-		   portmode_store);
-static DEVICE_ATTR(ethernet6_mode, S_IWUSR | S_IRUGO, portmode_show,
-		   portmode_store);
-#else
-static DEVICE_ATTR(ethernet5_mode, S_IRUGO, portmode_show, NULL);
-static DEVICE_ATTR(ethernet6_mode, S_IRUGO, portmode_show, NULL);
-#endif
-
-
-/*
- * PHY driver
- */
-
-static int
-mv88e6176_config_init(struct phy_device *pdev)
-{
-	dev_dbg(&pdev->dev, "%s\n", __func__);
-	pdev->state = PHY_RUNNING;
-
-	return 0;
-}
-
-/* check MV88E1111 PHY status and MV88E6176 GPIO */
-static int
-mv88e6176_read_status(struct phy_device *pdev)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
-	struct mv88e1111_port_state *state;
-	bool serdes, sfp_present, sfp_signal;
-	int port;
-	int ret = 0;
-	u16 gpio;
-
-	dev_dbg(&pdev->dev, "%s", __func__);
-	gpio = read_switch_scratch(pdev, MV_GPIO_DATA);
-	for (port = 5; port < 7; port++) {
-		serdes = (read_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_SR)
-			 & (1<<13)) ? 1 : 0;
-		dev_dbg(&pdev->dev, "%s: Port%d GPIO:0x%02x SerDes:%d\n",
-			__func__, port, gpio, serdes);
-		switch(port) {
-		case 5:
-			state = &priv->port5;
-			sfp_present = !((gpio >> 5) & 1);
-			sfp_signal = !((gpio >> 6) & 1);
-			break;
-		case 6:
-			state = &priv->port6;
-			sfp_present = !((gpio >> 3) & 1);
-			sfp_signal = !((gpio >> 4) & 1);
-			break;
-		}
-
-		/*
-		 * on sfp_detect read/verify SFP MSA and set sfp_compat
-		 * on sfp_signal issue link down?
-		 * on serdes auto-select
-		 */
-		if (state->sfp_present != sfp_present) {
-			state->sfp_present = sfp_present;
-			dev_info(&pdev->dev, "Port%d: SFP %s\n",
-				 port, sfp_present ? "inserted" : "removed");
-			if (state->sfp_present) {
-				if (gw16083_read_port_sfp(priv->client, state))
-					state->sfp_compat = false;
-				else
-					state->sfp_compat = true;
-				/* trigger a re-select/enable below */
-				state->serdes = !serdes;
-				pdev->state = PHY_RUNNING;
-			} else {
-				state->sfp_compat = false;
-				state->sfp_enabled = false;
-				pdev->state = PHY_NOLINK;
-			}
-		}
-		if (state->sfp_signal != sfp_signal) {
-			state->sfp_signal = sfp_signal;
-			dev_info(&pdev->dev, "Port%d: SFP signal %s\n",
-				 port, sfp_signal ? "detected" : "lost");
-		}
-		if (state->serdes != serdes) {
-			state->serdes = serdes;
-			dev_info(&pdev->dev, "Port%d: %s auto-selected\n",
-				 port, serdes ? "SERDES" : "copper");
-
-			/*
-			 * if auto-selection has switched to copper
-			 * disable serdes
-			 */
-			if (!serdes) {
-				config_mv88e1111_port_sfp(pdev, port, 0);
-				state->sfp_enabled = false;
-			}
-		}
-
-		/* if compatible SFP module and not yet enabled then enable */
-		if (state->sfp_compat && state->sfp_signal &&
-		    !state->sfp_enabled)
-		{
-			if (!config_mv88e1111_port_sfp(pdev, port, 1))
-				state->sfp_enabled = true;
-		}
-	}
-
-	return ret;
-}
-
-static int
-mv88e6176_config_aneg(struct phy_device *pdev)
-{
-	dev_dbg(&pdev->dev, "%s", __func__);
-	return 0;
-}
-
-static void
-mv88e6176_remove(struct phy_device *pdev)
-{
-	dev_dbg(&pdev->dev, "%s", __func__);
-
-	device_remove_file(&pdev->dev, &dev_attr_ethernet1);
-	device_remove_file(&pdev->dev, &dev_attr_ethernet2);
-	device_remove_file(&pdev->dev, &dev_attr_ethernet3);
-	device_remove_file(&pdev->dev, &dev_attr_ethernet4);
-	device_remove_file(&pdev->dev, &dev_attr_ethernet5);
-	device_remove_file(&pdev->dev, &dev_attr_ethernet6);
-	device_remove_file(&pdev->dev, &dev_attr_ethernet5_sfp);
-	device_remove_file(&pdev->dev, &dev_attr_ethernet6_sfp);
-	device_remove_file(&pdev->dev, &dev_attr_ethernet5_mode);
-	device_remove_file(&pdev->dev, &dev_attr_ethernet6_mode);
-	sysfs_remove_link(kernel_kobj, "gw16083");
-}
-
-static int
-mv88e6176_probe(struct phy_device *pdev)
-{
-	int port;
-	int ret = 0;
-	u32 id, reg;
-	struct mv88e1111_priv *priv;
-
-	dev_dbg(&pdev->dev, "%s: addr=0x%02x bus=%s:%s gw16083_client=%p\n",
-		__func__, pdev->addr, pdev->bus->name, pdev->bus->id,
-		gw16083_client);
-
-	/* In single-chip addressing mode the MV88E6176 shows up on 0x10-0x16 */
-	if (pdev->addr != MV_BASE)
-		return 0;
-
-	/* i2c driver needs to be loaded first */
-	if (!gw16083_client)
-		return 0;
-
-	/* gw16083 has MV88E1676 hanging off of i210 mdio bus */
-	if (strcmp(pdev->bus->name, "igb_enet_mii_bus") != 0)
-		return 0;
-
-	//dev_info(&pdev->dev, "Detected");
-	dev_info(&gw16083_client->dev, "%s: MV88E6176 7-port switch detected",
-		 pdev->bus->id);
-
-	/*
-	 * port5/6 config: MV88E1111 PHY
-	 * Register 20: PHY Control Register
-	 *   R20_7: add delay to RX_CLK for RXD
-	 *   R20_1: add delay to TX_CLK for TXD
-	 * Register 24: LED Control Register
-	 *   0x4111:
-	 *     Pulse stretch 170 to 340 ms
-	 * Register 0: Control Register
-	 *   R0_15: phy reset
-	 */
-	for (port = 5; port < 7; port++) {
-#ifndef RGMII_DELAY_ON_PHY
-		write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, 0xC003);
-#endif
-
-		id = read_switch_port_phy(pdev, port,
-					  MII_M1111_PHY_IDENT0) << 16;
-		id |= read_switch_port_phy(pdev, port, MII_M1111_PHY_IDENT1);
-		if ((id & MII_M1111_PHY_ID_MASK) != MII_M1111_PHY_ID) {
-			dev_err(&gw16083_client->dev,
-				"Port%d: No MV88E1111 PHY detected", port);
-			return 0;
-			//continue;
-		}
-
-#ifdef RGMII_DELAY_ON_PHY
-		/* phy rx/tx delay */
-		reg = read_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_CR);
-		reg |= (1<<1) | (1<<7);
-		write_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_CR, reg);
-#endif
-		/* led config */
-		write_switch_port_phy(pdev, port, MII_M1111_PHY_LED_CONTROL,
-				      MII_M1111_PHY_LED_PULSE_STR);
-		/* reset phy */
-		reg = read_switch_port_phy(pdev, port, MII_M1111_PHY_CONTROL);
-		reg |= MII_M1111_PHY_CONTROL_RESET;
-		write_switch_port_phy(pdev, port, MII_M1111_PHY_CONTROL, reg);
-		dev_info(&gw16083_client->dev,
-			 "Port%d MV88E111 PHY configured\n", port);
-	}
-
-	/*
-	 * GPIO Configuration:
-	 *  GPIO1: FIB5_TXEN# (output)
-	 *  GPIO2: FIB6_TXEN# (output)
-	 *  GPIO3: FIB6_PRES# (input)
-	 *  GPIO4: FIB6_LOS   (input)
-	 *  GPIO5: FIB5_PRES# (input)
-	 *  GPIO6: FIB5_LOS   (input)
-	 */
-	write_switch_scratch(pdev, MV_GPIO_DATA, 0x06); /* GPIO[2:1] out hi */
-	write_switch_scratch(pdev, MV_GPIO_DIR,  0x78); /* GPIO[6:3] inp */
-
-	pdev->irq = PHY_POLL;
-
-	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
-	memset(priv, 0, sizeof(*priv));
-	priv->phydev = pdev;
-	priv->client = gw16083_client;
-	priv->port5.port = 5;
-	priv->port6.port = 6;
-	dev_set_drvdata(&pdev->dev, priv);
-
-	ret |= device_create_file(&pdev->dev, &dev_attr_ethernet1);
-	ret |= device_create_file(&pdev->dev, &dev_attr_ethernet2);
-	ret |= device_create_file(&pdev->dev, &dev_attr_ethernet3);
-	ret |= device_create_file(&pdev->dev, &dev_attr_ethernet4);
-	ret |= device_create_file(&pdev->dev, &dev_attr_ethernet5);
-	ret |= device_create_file(&pdev->dev, &dev_attr_ethernet6);
-	ret |= device_create_file(&pdev->dev, &dev_attr_ethernet5_sfp);
-	ret |= device_create_file(&pdev->dev, &dev_attr_ethernet6_sfp);
-	ret |= device_create_file(&pdev->dev, &dev_attr_ethernet5_mode);
-	ret |= device_create_file(&pdev->dev, &dev_attr_ethernet6_mode);
-
-	if (unlikely(ret))
-		dev_err(&pdev->dev, "Failed creating attrs\n");
-
-	/* Add a nice symlink to the real device */
-	ret = sysfs_create_link(kernel_kobj, &pdev->dev.kobj, "gw16083");
-
-	dev_dbg(&pdev->dev, "initial state: GPIO=0x%02x "
-		"Port5_serdes=%d Port6_serdes=%d\n",
-		read_switch_scratch(pdev, MV_GPIO_DATA),
-		(read_switch_port_phy(pdev, 5, MII_M1111_PHY_EXT_SR)
-		 & (1<<13) ? 1:0),
-		(read_switch_port_phy(pdev, 6, MII_M1111_PHY_EXT_SR)
-		 & (1<<13) ? 1:0));
-
-	return ret;
-}
-
-static struct phy_driver mv88e6176_phy_driver = {
-	.name		= "MV88E6176",
-	.phy_id		= MV_IDENT_VALUE,
-	.phy_id_mask	= MV_IDENT_MASK,
-	.features	= PHY_BASIC_FEATURES,
-	.probe		= &mv88e6176_probe,
-	.remove		= &mv88e6176_remove,
-	.config_init	= &mv88e6176_config_init,
-	.config_aneg	= &mv88e6176_config_aneg,
-	.read_status	= &mv88e6176_read_status,
-	.driver		= { .owner = THIS_MODULE },
-};
-
-/*
- * I2C driver
- */
-
-/* See SFF-8472 */
-struct sfp_msa {
-	/* Basic ID fields */
-	u8	identifier;
-	u8	ext_identifier;
-	u8	connector;
-	u8	transceiver[8];
-	u8	encoding;
-	u8	br_nominal;
-	u8	rate_identifier;
-	u8	length_smf_km;
-	u8	length_smf;
-	u8	length_om2;
-	u8	length_om1;
-	u8	length_om4;
-	u8	length_om3;
-	u8	vendor_name[16];
-	u8	transceiver2;
-	u8	vendor_oui[3];
-	u8	vendor_pn[16];
-	u8	vendor_rev[4];
-	u8	wavelength[2];
-	u8	resv1;
-	u8	cc_base;
-
-	/* extended id fields */
-	u8	options[2];
-	u8	br_max;
-	u8	br_min;
-	u8	vendor_sn[16];
-	u8	date_code[8];
-	u8	diags_type;
-	u8	enhanced_options;
-	u8	sff8472_compliance;
-	u8	cc_ext;
-
-	/* Vendor specific ID fields */
-	u8	vendor_data[32];
-	u8	sff8079[128];
-};
-
-enum identifier {
-	UNKNOWN,
-	GBIC,
-	SFF,
-	SFP,
-	XBI,
-	XENPACK,
-	XFP,
-	XFF,
-	XFP_E,
-	XPAK,
-	X2,
-	DWDM_SFP,
-	QSFP,
-	MAX_ID,
-};
-
-const char* id_names[] = {
-	"UNKONWN",
-	"GBIC",
-	"SFF",
-	"SFP",
-	NULL,
-};
-
-/* Flags for SFP modules compatible with ETH up to 1Gb */
-struct sfp_flags {
-	u8 e1000_base_sx:1;
-	u8 e1000_base_lx:1;
-	u8 e1000_base_cx:1;
-	u8 e1000_base_t:1;
-	u8 e100_base_lx:1;
-	u8 e100_base_fx:1;
-	u8 e10_base_bx10:1;
-	u8 e10_base_px:1;
-};
-
-#define STRING_APPEND(str, src)				\
-	strncat(str, src, sizeof(src));			\
-	for (i = 1; i < sizeof(str); i++)		\
-		if (str[i-1] == ' ' && str[i] == ' ')	\
-			str[i] = 0;
-
-static int gw16083_read_port_sfp(struct i2c_client *client,
-				 struct mv88e1111_port_state *state)
-{
-	int ret = 0;
-	u8 data[256];
-	struct sfp_flags *eth_flags;
-	u8 crc;
-	int i;
-	u8 *str;
-	struct sfp_msa *sfp_msa = (struct sfp_msa *)data;
-	int port = state->port;
-	union i2c_smbus_data d;
-
-	dev_dbg(&client->dev, "%s Port%d\n", __func__, port);
-	if (!i2c_check_functionality(client->adapter,
-				     I2C_FUNC_SMBUS_READ_I2C_BLOCK))
-		return -ENODEV;
-	d.byte = (port == 5) ? 1 : 2;
-	if (i2c_smbus_xfer(client->adapter, GW16083_I2C_ADDR_PCA9543,
-			   client->flags, I2C_SMBUS_WRITE, 0,
-			   I2C_SMBUS_BYTE_DATA, &d) < 0)
-	{
-		dev_err(&client->dev,
-			"Port%d: failed writing PCA9543 register\n", port);
-		return ret;
-	}
-
-	/* read all 256 bytes of SFP EEPROM */
-	for (i = 0; i < sizeof(data); i += I2C_SMBUS_BLOCK_MAX) {
-		d.block[0] = I2C_SMBUS_BLOCK_MAX;
-		if (i2c_smbus_xfer(client->adapter, GW16083_I2C_ADDR_SFP1,
-				   client->flags, I2C_SMBUS_READ, i,
-				   I2C_SMBUS_I2C_BLOCK_DATA, &d) < 0)
-		{
-			dev_err(&client->dev,
-				"Port%d: failed reading SFP data\n", port);
-			return ret;
-		}
-		memcpy(data + i, d.block + 1, I2C_SMBUS_BLOCK_MAX);
-	}
-
-	/* Validate checksums */
-	for (crc = 0, i = 0; i < 63; i++)
-		crc += data[i];
-	if (crc != sfp_msa->cc_base) {
-		dev_err(&client->dev, "Port%d: "
-			"Checksum failure for Base ID fields: 0x%02x\n", port,
-			crc);
-#ifdef FAIL_ON_CHECKSUM_ERR
-		return -EINVAL;
-#endif
-	}
-	for (crc = 0, i = 64; i < 95; i++)
-		crc += data[i];
-	if (crc != sfp_msa->cc_ext) {
-		dev_err(&client->dev, "Port%d: "
-			"Checksum failure for Extended ID fields: 0x%02x\n",
-			port, crc);
-#ifdef FAIL_ON_CHECKSUM_ERR
-		return -EINVAL;
-#endif
-	}
-	state->sfp_id[0] = 0;
-	for (i = 0; id_names[i]; i++) {
-		if (sfp_msa->identifier == i) {
-			sprintf(state->sfp_id, "%s: ", id_names[i]);
-			break;
-		}
-	}
-	STRING_APPEND(state->sfp_id, sfp_msa->vendor_oui);
-	STRING_APPEND(state->sfp_id, sfp_msa->vendor_name);
-	STRING_APPEND(state->sfp_id, sfp_msa->vendor_pn);
-	STRING_APPEND(state->sfp_id, sfp_msa->vendor_rev);
-	STRING_APPEND(state->sfp_id, sfp_msa->vendor_sn);
-	dev_info(&client->dev, "Port%d: %s\n", port, state->sfp_id);
-
-	if ((sfp_msa->identifier != GBIC) &&
-	    (sfp_msa->identifier != SFF) &&
-	    (sfp_msa->identifier != SFP))
-	{
-		dev_err(&client->dev, "Port%d: Unknown module identifier: %d\n",
-			port, sfp_msa->identifier);
-		return -EINVAL;
-	}
-
-	str = "";
-	eth_flags = (struct sfp_flags *)(sfp_msa->transceiver + 3);
-	if (eth_flags->e1000_base_sx) {
-		str = "1000Base-SX (Fiber)";
-	} else if (eth_flags->e1000_base_lx) {
-		str = "1000Base-LX (Fiber)";
-	} else if (eth_flags->e1000_base_t) {
-		str = "1000Base-T (Copper)";
-	} else if (eth_flags->e100_base_fx) {
-		str = "100Base-FX (Fiber) - not supported";
-		ret = -EINVAL;
-	} else {
-		str = "Unknown/Unsupported media type";
-		ret = -EINVAL;
-	}
-	if (ret)
-		dev_err(&client->dev, "Port%d: %s (0x%02x)\n", port, str,
-			sfp_msa->transceiver[3]);
-	else
-		dev_info(&client->dev, "Port%d: %s (0x%02x)\n", port, str,
-			sfp_msa->transceiver[3]);
-
-	return ret;
-}
-
-static int gw16083_probe(struct i2c_client *client,
-			 const struct i2c_device_id *id)
-{
-	int ret;
-
-	dev_info(&client->dev, "GW16083 Ethernet Expansion Mezzanine\n");
-	if (gw16083_client) {
-		dev_err(&client->dev, "client already registered\n");
-		return -EINVAL;
-	}
-	gw16083_client = client;
-
-	ret = phy_driver_register(&mv88e6176_phy_driver);
-	if (ret)
-		dev_err(&client->dev,
-			"failed to register mv88e6176 phy driver: %d\n", ret);
-	return ret;
-}
-
-static int gw16083_remove(struct i2c_client *client)
-{
-	dev_dbg(&client->dev, "%s\n", __func__);
-
-	phy_driver_unregister(&mv88e6176_phy_driver);
-	gw16083_client = NULL;
-	return 0;
-}
-
-static const struct of_device_id gw16083_dt_ids[] = {
-	{ .compatible = "gateworks,gw16083", },
-	{ }
-};
-
-MODULE_DEVICE_TABLE(of, gw16083_dt_ids);
-
-static const struct i2c_device_id gw16083_id[] = {
-	{ "gw16083", 0 },
-	{ }
-};
-MODULE_DEVICE_TABLE(i2c, gw16083_id);
-
-static struct i2c_driver gw16083_driver = {
-	.driver = {
-		.name	= "gw16083",
-		.of_match_table = gw16083_dt_ids,
-	},
-	.probe		= gw16083_probe,
-	.remove		= gw16083_remove,
-	.id_table	= gw16083_id,
-};
-
-static int __init mv88e6176_init(void)
-{
-	return i2c_add_driver(&gw16083_driver);
-}
-
-static void __exit mv88e6176_exit(void)
-{
-	i2c_del_driver(&gw16083_driver);
-}
-
-module_init(mv88e6176_init);
-module_exit(mv88e6176_exit);
diff --git a/target/linux/imx6/files-4.1/drivers/net/phy/gw16083.h b/target/linux/imx6/files-4.1/drivers/net/phy/gw16083.h
deleted file mode 100644
index db96f2b7b3..0000000000
--- a/target/linux/imx6/files-4.1/drivers/net/phy/gw16083.h
+++ /dev/null
@@ -1,123 +0,0 @@
-/*
- * drivers/net/phy/mv88e6176.h
- *
- * Driver for Marvell Switch
- *
- * Author: Tim Harvey
- *
- * Copyright (c) 2014 Tim Harvey <tharvey@gateworks.com>
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- *
- */
-
-#ifndef _GW16083_H_
-#define _GW16083_H_
-
-#define MII_MARVELL_PHY_PAGE		22
-
-/*
- * I2C Addresses
- */
-#define GW16083_I2C_ADDR_SFP1		0x50
-#define GW16083_I2C_ADDR_SFP2		0x51
-#define GW16083_I2C_ADDR_EEPROM		0x52
-#define GW16083_I2C_ADDR_PCA9543	0x70
-
-/*
- * MV88E1111 PHY Registers
- */
-enum {
-	MII_M1111_PHY_CONTROL		= 0,
-	MII_M1111_PHY_STATUS 		= 1,
-	MII_M1111_PHY_IDENT0		= 2,
-	MII_M1111_PHY_IDENT1		= 3,
-	MII_M1111_PHY_EXT_CR		= 20,
-	MII_M1111_PHY_LED_CONTROL	= 24,
-	MII_M1111_PHY_EXT_SR		= 27,
-};
-
-#define MII_M1111_PHY_ID_MASK		0xfffffff0
-#define MII_M1111_PHY_ID		0x01410cc0
-
-#define MII_M1111_PHY_CONTROL_RESET	(1 << 15)
-#define MII_M1111_PHY_LED_DIRECT	0x4100
-#define MII_M1111_PHY_LED_PULSE_STR	0x4111
-#define MII_M1111_PHY_LED_COMBINE	0x411c
-#define MII_M1111_RX_DELAY		0x80
-#define MII_M1111_TX_DELAY		0x2
-
-/*
- * MV88E6176 Switch Registers
- */
-
-/* PHY Addrs */
-#define MV_BASE		0x10
-#define MV_GLOBAL1	0x1b
-#define MV_GLOBAL2	0x1c
-#define MV_GLOBAL3	0x1d
-
-/* Global2 Registers */
-enum {
-	MV_SMI_PHY_COMMAND	= 0x18,
-	MV_SMI_PHY_DATA		= 0x19,
-	MV_SCRATCH_MISC		= 0x1A,
-};
-
-/* Scratch And Misc Reg offsets */
-enum {
-	MV_GPIO_MODE		= 0x60,
-	MV_GPIO_DIR		= 0x62,
-	MV_GPIO_DATA		= 0x64,
-	MV_GPIO76_CNTL		= 0x6B,
-	MV_GPIO54_CNTL		= 0x6A,
-	MV_GPIO32_CNTL		= 0x69,
-	MV_GPIO10_CNTL		= 0x68,
-	MV_CONFIG0		= 0x70,
-	MV_CONFIG1		= 0x71,
-	MV_CONFIG2		= 0x72,
-	MV_CONFIG3		= 0x73,
-};
-
-/* PHY Registers */
-enum {
-	MV_PHY_CONTROL      = 0x00,
-	MV_PHY_STATUS       = 0x01,
-	MV_PHY_IDENT0       = 0x02,
-	MV_PHY_IDENT1       = 0x03,
-	MV_PHY_ANEG         = 0x04,
-	MV_PHY_LINK_ABILITY = 0x05,
-	MV_PHY_ANEG_EXPAND  = 0x06,
-	MV_PHY_XMIT_NEXTP   = 0x07,
-	MV_PHY_LINK_NEXTP   = 0x08,
-	MV_PHY_CONTROL1     = 0x10,
-	MV_PHY_STATUS1      = 0x11,
-	MV_PHY_INTR_EN      = 0x12,
-};
-
-/* Port Registers */
-enum {
-	MV_PORT_STATUS      	= 0x00,
-	MV_PORT_PHYS_CONTROL	= 0x01,
-	MV_PORT_IDENT       	= 0x03,
-	MV_PORT_CONTROL     	= 0x04,
-	MV_PORT_VLANMAP     	= 0x06,
-	MV_PORT_ASSOC       	= 0x0b,
-	MV_PORT_RXCOUNT     	= 0x10,
-	MV_PORT_TXCOUNT     	= 0x11,
-};
-
-#define SMIBUSY		(1<<15)
-#define SMIMODE22	(1<<12)
-#define SMIOP_READ	(2<<10)
-#define SMIOP_WRITE	(1<<10)
-#define DEVADDR		5
-#define REGADDR		0
-
-#define MV_IDENT_MASK		0x0000fff0
-#define MV_IDENT_VALUE		0x00001760
-
-#endif /* _GW16083_H_ */